Related Manuals for Husqvarna 7002
Summary of Contents for Husqvarna 7002
- Page 1 07002 LGT2554 Owner's Manual "This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only. Do not use any fuel >E10 in this machine." 532 44 02-80...
-
Page 2: Safety Rules
Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent ac ci den tal starting when setting up, trans port ing, ad just ing or making repairs, al ways dis con nect spark plug wire and place... - Page 3 Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the ma chine and the mowing activity. Never assume that children will remain where you last saw them. •...
-
Page 4: Table Of Contents
Gasoline Capacity 4 Gallons and type: Unleaded Regular Oil Type (API-SG-SL): SAE 10W-30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: W/ Filter: Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: Reverse: Charging System: 15 AMPS @ 3600 RPM Battery: AMP/HR: MIN. -
Page 5: Assembly
UNASSEMBLED PARTS Mower (2) Rear Lift Link Assemblies (1) Small Retainer Springs (1) Front (5) Large Retainer Springs If Equipped (1) Anti-Sway Bar (1) Small Retainer Springs Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. - Page 6 ADJUST SEAT (See Fig. 2) • Sit in seat. • Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down. • Release lever to lock seat in position. Fig.
- Page 7 CAUTION: Continuing to press the electric lift switch after the mower deck has reached the minimum or maximum position may result in damage to the electric lift mechanism.The electric lift mechanism is equipped with a thermal protection system. If the system overheats or fails to operate, allow the sys- tem to cool before attempting to operate again.
- Page 8 ANTI-SWAY BAR (S) LOCATION Fig. 9 NOTE: Depending on model, bracket (T) may be differ- ent than shown but hole for anti-sway bar will be in same position/location. • Pivot the integrated washer end of anti-sway bar (S) towards mower deck bracket on right side of mower. Insert integrated washer end of bar into hole in rear mower bracket (D).
- Page 9 9 INSTALL BELT ON ENGINE CLUTCH PULLEY (M) (See Fig. 6 & 14) • Disengage belt tension rod (K) from locking bracket (L). • Install belt onto engine clutch pulley (M). M. ENGINE CLUTCH PULLEY Fig. 14 IMPORTANT: Check belt for proper routing in all mower pulley grooves and under mandrel covers.
-
Page 10: Operation
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. REVERSE NEUTRAL REVERSE ENGINE OFF OPERATION SYSTEM (ROS) LIGHTS ON BATTERY FUEL ATTACHMENT ATTACHMENT CLUTCH DISENGAGED CLUTCH ENGAGED FREE WHEEL (Automatic Models only) Failure to follow instructions could result in serious injury or death. - Page 11 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your trac tor.
- Page 12 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
- Page 13 TO MOVE FORWARD AND BACKWARD (See Fig. 19) The direction and speed of movement is controlled by the motion control lever. (J) Fig. 19 • Start tractor with motion control le ver in neutral position. • Release parking brake. • Slowly move motion control lever to desired position.
- Page 14 REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.
-
Page 15: Before Starting The Engine
BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory, already filled with sum mer weight oil. • Check engine oil with tractor on level ground. • Pull up and remove oil fill cap/dipstick; wipe oil off. Reinsert the dipstick into the tube and push down firmly into place. -
Page 16: Mowing Tips
PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. To ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel- oped during shipping of your tractor. -
Page 17: Maintenance Schedule
MAINTENANCE SCHEDULE Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Clean Debris Off Steering Plate ck Transaxle Cooling Check Mower Levelness ck V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) -
Page 18: Maintenance
TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE”... -
Page 19: V-Belts
TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos- si ble damage to seals, do not use high pressure water or steam to clean transmission. -
Page 20: Deck Washout Port
IN-LINE FUEL FILTER (See Fig. 29) The fuel filter should be replaced once each season. If fuel filter becomes clogged, ob struct ing fuel flow to car bu re tor, re place ment is re quired. • With engine cool, remove filter and plug fuel line sec tions. •... -
Page 21: Service And Adjustments
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SE RI OUS IN JU RY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position. •... - Page 22 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
-
Page 23: Front Wheel Toe-In/Cam Ber
SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 38) Park the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - 1. - Page 24 SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 40) The motion control lever has been pre set at the factory and adjustment should not be necessary. • Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
-
Page 25: To Remove Hood And Grill Assembly
Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. • To replace, reverse above procedure. 07002 NEGATIVE (BLACK) CABLE TRANSMISSION REMOVAL/RE PLACE MENT Should your transmission require removal for service or re place ment, it should be purged after reinstallation and before operating the tractor. -
Page 26: Storage
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. -
Page 27: Trou Ble Shoot Ing
TROUBLESHOOTING POINTS PROBLEM CAUSE 1. Out of fuel. Will not start 2. Engine not “CHOKED” properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9. - Page 28 TROUBLESHOOTING POINTS PROBLEM CAUSE Engine continues 1. Faulty operator-safety presence control system. to run when oper- ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. Poor cut - uneven 2. Mower deck not level. 3. Buildup of grass, leaves, trash under mower. 4.
-
Page 29: Repair Parts
SCHEMATIC SCH12 PTO SWITCH (MATING SIDE) IGNITION SWITCH POSITION CIRCUIT “MAKE” M+G+A1 B+A1 RUN/OVERRIDE B+A1 L+A2 START B + S + A1 BATTERY FUSE AMMETER (OPTIONAL) WHITE PTO SWITCH (DISENGAGED) WHITE BLACK BLACK BLACK BLACK BLACK IGNITION UNIT (OPTIONAL) HOUR BLUE METER FUEL... - Page 30 TRACTOR - MODEL NO. LGT2554 (96045003100), PRODUCT NO. 960 45 00-31 ELECTRICAL T07S With 12V Outlet Option With Service Minder Option...
- Page 31 ELECTRICAL PART DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 532 41 41-26 Battery Box 532 17 61-38 Switch Interlock 532 40 02-52 Harness Socket Light 532 00 41-52 Bulb, Light #1156 532 40 02-53 Cable Battery 532 41 28-95 Cable Starter...
- Page 32 CHASSIS Chassis-tex_GT HUSQ_II_15...
- Page 33 CHASSIS PART DESCRIPTION 532 43 97-52 Logo 532 43 74-72 Dash 532 43 97-25 Hood Asm. 532 43 97-33 Lens LH 532 43 77-62 Grille Asm. 532 43 97-32 Lens RH 532 19 61-25 Plate Engine 817 06 05-12 Screw 5/16-18 x 3/4 532 40 18-25 Fender 873 68 05-00...
- Page 34 DRIVE drive-tex_K46_fender_6_r3...
- Page 35 DRIVE PART DESCRIPTION - - - - - - - - - Transaxle, TUFFTORQ K46 AW (Internal parts not available) 532 18 62-11 532 19 98-44 Hub Asm. Wheel Rear 22" TX GT .06 532 14 00-80 Bolt Hub Wheel Rear 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
- Page 36 ENGINE 21 20 engine-tex_Kohl_19 PART DESCRIPTION - - - - - - - - - Engine Kohl Model No. SV730-3034 532 14 97-23 Muffler 532 19 43-20 Keeper Belt Engine 532 17 93-35 Clutch Electric 532 19 43-43 Pulley Engine 532 41 41-52 Tank Fuel 4.0 532 43 02-13...
-
Page 37: Seat Assembly
SEAT ASSEMBLY seat-tex_6.5SL_3 PART DESCRIPTION 532 42 40-68 Seat 532 18 01-66 Bracket Pivot Fender 532 14 06-75 Strap, Asm Fender 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc 532 12 41-81 Spring, Seat Cprsn 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems 532 19 69-77 Pan, Seat 532 17 18-52... - Page 38 STEERING ASSEMBLY steering-tex_HUSQSR_14...
-
Page 39: Steering Assembly
STEERING ASSEMBLY PART DESCRIPTION 532 41 64-80 Wheel, Steering 532 19 59-68 Axle Asm., Front 532 40 30-89 Spindle Asm., LH 532 40 30-90 Spindle Asm., RH 532 12 49-31 Bearing, Race Thrust Harden 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga. 812 00 00-29 Ring, Clip #T5304-75 532 12 12-32... -
Page 40: Mower Deck
MOWER DECK mower_deck 54-tex_16... - Page 41 MOWER DECK PART DESCRIPTION 532 40 31-25 Deck Weldment Mower 532 19 60-66 Cover Mandrel LH 532 19 71-81 Cover Mandrel RH 532 19 30-03 Bolt 7/16 Asm. Blade 532 18 72-56 Blade Bagging 532 18 72-55 Blade Mulching 532 40 48-51 Rod Anti Sway 532 18 72-91 Shaft Asm.
-
Page 42: Mower Lift
MOWER LIFT lift-tex_23 PART DESCRIPTION 532 42 20-27 Shaft Asm., Lift 532 19 52-30 Lever Asm., Lift RH 532 41 15-55 Grip, Lever 532 19 63-14 Spring Torsion 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock 532 19 53-04 Spring Lift Assist 819 19 19-12 Washer Clear Zinc... -
Page 43: Wheels And Tires
DECALS KEY PART DESCRIPTION 532 41 16-57 Decal, Warning 532 42 41-02 Decal, Warning Spark Arrestor 532 19 15-54 Decal, Fender 532 17 84-55 Decal, Caution 532 43 63-90 Label Emiss. CA. 532 19 87-85 Decal, Mower Sch. 532 14 50-05 Decal, Battery Dnge/Poi 532 44 03-73 Decal, Panel Side... - Page 48 11.10.10 JA Printed in the U.S.A.