Front Glass Enclosure Panel, Removal And Installation - Lennox Montebello MDLX40IN Care And Operation Instructions Manual

LENNOX HEARTH PRODUCTS • MONTEBELLO
FRONT GLASS ENCLOSURE PANEL,
REMOVAL AND INSTALLATION
WARNING
• When reinstalling the glass
door, the door latch screws
must be securely tightened
to prevent the glass door
from falling out, which could
potentially cause damage
and possible injury.
• Do not attempt to substitute
the materials used on this
door, or replace cracked or
broken glass.
• Handle this glass with
extreme care! Glass is
susceptible to damage – Do
not scratch or handle roughly
while reinstalling the glass
door frame.
• The glass door of this
appliance must only be
replaced as a complete
unit as provided by the
manufacturer. Do not attempt
to replace broken, cracked or
chipped glass separately.
• Do not attempt to touch
the front enclosure glass
with your hands while the
fi replace is in use.
WARNING
Do not operate appliance
with the glass front removed,
cracked or broken.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou
brisé.
10
® DLX DIRECT VENT GAS FIREPLACES (MDLX40/45) • CARE AND OPERATION INSTRUCTIONS
WARNING
Any safety screen or guard
removed for servicing the
appliance must be replaced
prior to operating the
appliance.
AVERTISSEMENT
Tout écran ou protecteur retiré
pour permettre l'entretien
de l'appareil doit être remis
en place avant de mettre
l'appareil en marche.
Only doors certifi ed with the appliance
shall be used.
Seules des portes certifi ées pour cet
appareil doivent être utilisées.
CAUTION: DO NOT abuse glass door by
striking or slamming shut.
These are direct-vent appliances. They
are designed to operate only when the
front glass enclosure panel is installed.
Generally the front glass enclosure panel
should not be removed except to gain
access to the components within the
fi rebox.
Removing Glass Enclosure Panel
Refer to Figure 3. To remove the
fi rescreens, lift up the center of the rod
to disengage it from the center bracket,
bend down at center, hold left side with
hand until it disengages from left side,
being careful not to scratch paint. Slowly
remove the rod from the right side.
Remove the door modesty shield from
the top fl ange of the glass door by
pulling it up fi rmly with both hands until
it is disengaged. Using a Phillips head
screwdriver, unfasten the two (2) screws
located at the top of the glass frame.
Tilt the glass frame at the top away from
the unit. Lift it carefully off the bottom
door track and set the door aside,
protecting it from inadvertent damage.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
To install the front glass door
assembly, proceed as follows:
Step 1. Retrieve the glass door
assembly. Visually inspect the
gasket on the backside of the
panel. The gasket surface must
be clean, free of irregularities
and seated fi rmly.
Step 2. Position the door frame in
front of the fi rebox opening and
engage the bottom fl ange over
the rail at the bottom of the
fi rebox opening.
Step 3. Swing the door up and back.
Ensure the gasket seats evenly
as the door draws shut. Engage
the nut insert and fasten with
two screws to secure the door.
Step 4. Install the door modesty shield
on top fl ange glass door as
follows: grab the door modesty
shield with both hands, with
the open hem going down and
engage it with the upper lip of
the glass door frame by pushing
it all the way down. Make sure
the installed shield is fi rmly in
place.
Step 5. With the fi rescreen hanging
on the screen rod, drop in the
right side of the rod to the right
modesty panel. Then drop in
the left side of the rod through
the slot of the left modesty
panel. Make sure that the rod is
supported by the bracket in the
center of the fi replace.
Top Flange Glass Door
Glass Door Latch (2)
Frame Assembly
Screws
Firebox Floor
Glass Door Assembly
Figure 3: Glass Door Assembly
Removal/Installation