OBJ_BUCH-1039-002.book Page 19 Thursday, January 14, 2010 6:17 PM English | 19 Safety Notes influence of drugs, alcohol, or medication. A mo- ment of inattention while operating a pneumatic tool may result in personal injury. General Safety Rules for Pneumatic Tools b)Use personal protective equipment.
Page 7
OBJ_BUCH-1039-002.book Page 20 Thursday, January 14, 2010 6:17 PM 20 | English d)Disconnect the air supply before making any ad- Do not work on ladders or scaffolds when the justments, changing accessories, or placing the actuation system “Contact actuation” is set. pneumatic tool aside.
English | 21 Functional Description Technical Data Read all safety warnings and all instructions. Compressed-air nailer GSK 64 Failure to follow the warnings and instructions Professional may result in electric shock, fire and/or serious Article number 3 601 D91 9..
Loading the Magazine (see figures B1 – Disconnect the air supply before making any adjustments, changing accessories, or plac- Robert Bosch GmbH, Power Tools Division ing the pneumatic tool aside. This safety D-70745 Leinfelden-Echterdingen Leinfelden, 07.12.2009 measure prevents accidental starting of the pneumatic tool.
OBJ_BUCH-1039-002.book Page 23 Thursday, January 14, 2010 6:17 PM English | 23 – With the nail pusher 13 pressed, carefully guide the – Afterwards, briefly press trigger 5 and release again. magazine slider 12 toward the front until the nail push- A nail is discharged.
Page 11
OBJ_BUCH-1039-002.book Page 24 Thursday, January 14, 2010 6:17 PM 24 | English Avoid any weakening and damage whatsoever of the Adjusting the Depth Stop (see figure F) pneumatic tool, e.g., through: The driving depth of the nails can be set with depth stop –...
OBJ_BUCH-1039-002.book Page 25 Thursday, January 14, 2010 6:17 PM English | 25 Changing the Workpiece Protector (see figure H) Adjustable Air-outlet cap (see figure I) The workpiece protector 1 at the end of the discharge With the adjustable exhaust cap at the air outlet 4, it is lock-off 2 protects the workpiece until the pneumatic tool possible to deflect the exhaust air away from yourself or is correctly placed for the driving procedure.
OBJ_BUCH-1039-002.book Page 26 Thursday, January 14, 2010 6:17 PM 26 | English Maintenance Schedule Always keep air outlet 4, discharge lock-off 2 and trigger Clean the magazine 11. Remove any plastic or wood chips 5 clean and free of foreign material (dust, chips, sand, that may accumulate in the magazine during operation.
OBJ_BUCH-1039-002.book Page 27 Thursday, January 14, 2010 6:17 PM English | 27 Correction of Malfunctions Problem Cause Corrective Measure The pneumatic tool is ready for A nail is jammed in the shot duct. – Clear the jam. operation but no nails are dis- (See “Clearing Jams”, page 24) charged.
Page 15
OBJ_BUCH-1039-002.book Page 28 Thursday, January 14, 2010 6:17 PM 28 | English Problem Cause Corrective Measure The nails are not driven in deep The rated pressure of the compressed- – Increase the compressed-air supply. enough. air supply is too low. 8 bar may not be exceeded.
Page 16
Australia, New Zealand and Pacific Islands 37589 Kalefeld The units will be disassembled. Plastics, e.g., the housing Robert Bosch Australia Pty. Ltd. which are primarily made of polyamide, are identified Power Tools (Bosch detection code for plastics since 1992) and recy- Locked Bag 66 cled.