American Standard CADET 2568 Installation Instructions page 3

9
TOP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
FLOAT
CUP
FILL
VALVE
VALVE
BODY
ADJUSTABLE
HEIGHT
LOCK NUT
CONE WASHER
COUPLING NUT
(HAND TIGHT ONLY)
11
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
! WARNING:
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
FLUIDMASTER
WATER CONTROL
TANK COVER
TRIP
LEVER
BOLT
CAPS
ARM
REFILL
NIPPLE
TUBE
TANK
LEVER
Fig. 9A
"S"
CLIP
FLUSH
VALVE
WATER LEVEL
ADJUSTMENT
ROD
FLAPPER
SHANK
WASHER
THREADED
SHANK
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
Diagram 1
F L U S H VA L V E
COMPACT CADET
Repair parts are determined by toilet tank number wich can be found marked inside tank.
NOTE: "XXX" represents color options. Specify when ordering.
COMPONENT
735125-XXX0A
735139-XXX0A
5332.016.XXX
5357.016.XXX
034783-XXX0A
738903-XXX0A
7381084-XXX0A
738919.XXX0A
738565-409.0070A
738565-440.0070A
738942-1000A
738942-1030A
738920-0070A
738942-1020A
7381043-4000A
ADJUSTMENTS
a. Adjust water level. Water level
should be adjusted to level indicated
on tank by adjusting float cup.
See Step 10 for water level adjustment
method.
b. If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 9A) and
take up slack on the chain, and
reinsert on lift rod. Make sure the chain
is not too taught.
FLAPPER
ASSEMBLY
®
3 ONE PIECE REPAIR PARTS LIST
DESCRIPTION
Tank Cover
Tank Cover
Seat - Elongated
Seat - Elongated
Bolt Cap Kit
Trip Lever - Left Hand
Trip Lever - Left Hand
Trip Lever - Right Hand
Inlet Valve
Inlet Valve
Flush Valve - 1.6 GPF
Flush Valve - 1.6 GPF
Flapper Assembly - 1.6 GPF
Flush Valve - 1.28 GPF
Flapper Assembly - 1.28 GPF
- 3 -
10
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
SEAT AND COVER
(INCLUDES MTG. KIT)
SEAT POST
MTG. KIT
2568
1.6
GPF
√
√
√
√
√
√
√
√
7 3 0 1 2 7 0 - 1 0 0 Re v. D
2907
1.28 1.6
GPF GPF
√
√
√
√
√ √
√
√
√
√
√
√
√
√
√