Timer Recording; Note For Timer Recording & Otr - Magnavox DV220MW9 A Owner's Manual

Timer Recording

VCR
Press first.
VHS VHS VHS VHS VHS
1
SETUP
Press , use
"TIMER PROGRAMMING".
Then, press
2
Use /
empty program number. Then,
press to go to next step.
3
Use /
"ONCE", "DAILY" (Mon-Fri), or
"WEEKLY". Then, press
to go to to go to next step.
4
Use /
desired month. Then, press
to go to the next step.
Then, repeat procedures above to select the day, start
time, end time, and "L1" or "L2" as well.
5
Use /
recording speed. Then, press
To set another program after step 5, press
Then, repeat procedures from steps 2 through 5.
You can program the unit to record up to 8 programs,
and up to 1 year in advance.
6
TIMER SET
Press to set the timer standby mode.
The [TIMER REC] indicator on this unit lights up and
the unit goes to the DVD mode.
Note: • To go back one step, press [s [ [ ] during steps 3 to
5.
• Select "L1" or "L2" to activate rear input jacks or
front input jacks accordingly.
EN EN
RECORDING
/ to select
to go to next step.
- M E N U - TIMER PROGRAMMING
B TIMER PROGRAMMING
PROG 12345678
SATELLITE LINK
DATE
AUTO REPEAT [OFF]
START TIME
CLOCK SET
END TIME
LANGUAGE SELECT
L1/L2
REC SPEED
Available program
number blinks.
to select an
PROGRAM NUMBER 1
DATE – – / – –
START TIME – – : – –
END TIME – – : – –
L1/L2 – –
REC SPEED – –
to select
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
to select the
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 0 6 TUE
START TIME – – : – –
END TIME – – : – –
L1/L2 – –
REC SPEED – –
ONE TIME PROGRAM
to select
PROGRAM NUMBER 1
DATE 1 0 / 0 6 TUE
CLEAR
START TIME 0 7 : 3 0
.
END TIME 0 8 : 3 0
L1/L2 L1
REC SPEED SP
B SP
SLP
]
To Check, Correct or Cancel a Timer Prog g g To Check, Correct or Cancel a Timer Program To Check, Correct or Cancel a Timer Program
1) Press [TIMER SET], and then press [VCR
remote control.
2) Repeat procedures in step 1 above.
3) Use [K / L] to select the program number you want
to check. The details of the program you select will
appear on the TV screen.
Use [s / B] to go to the digit you want to change.
Then, use [K / L] to enter the correct numbers.
You can cancel the entire program by pressing [s]
while the program number blinks.
4) Press [CLEAR] to exit.
5) Press [TIMER SET] to return to the timer standby
mode.
To Cancel a Timer Recording in Progress To Cancel a Timer Recording in Progress
– –
– – Press [STOP/EJECT C A] on the unit.
Note for Timer Recording & OTR
• If there is no cassette tape in the unit or the cassette
tape does not have the erase-protection tab,
the [TIMER REC] indicator blinks and timer recording
cannot be performed.
• If there is a power failure occurred or the unit is
unplugged for more than 30 seconds, clock setting and
– –
all programmed timer recordings will be lost.
– –
• If a cassette tape runs out before an OTR or a timer
recording is finished, the unit ejects the cassette tape.
After an OTR or a Timer Recording Has After an OTR or a Timer Recording Has After an OTR or a Timer Recording Has
Been Set, This Unit Operates as Follows: Been Set, This Unit Op p p Been Set, This Unit Operates as Follows:
• Press [TIMER SET] on the remote control or [STOP/
PM EJECT C A] on the unit, then press [VCR
PM
the VCR function again.
• To cancel the timer standby mode, press [TIMER SET] on
.
the remote control or [STOP/EJECT C A] on the unit,
then press [VCR
When an OTR or a Timer Recording g g When an OTR or a Timer Recording is Completed. When an OTR or a Timer Recording is Completed.
• If "AUTO POWER OFF" function for DVD has been
activated and some timer programming are left, the
[TIMER REC] indicator lights up and the unit goes to the
timer standby mode.
• The [TIMER REC] indicator blinks if there are no more
timer programming.
• If auto power off for DVD has NOT been activated, the
unit goes to the DVD mode and all the VCR functions
will be unavailable. All the DVD functions are available
during OTR, timer standby mode and timer recording.
• Press [STOP/EJECT C A] on this unit or [TIMER SET]
on the remote control to use the VCR when the unit is
turned off.
To Use the DVD Player During Timer To Use the DVD Player During Timer
Recording or While the [TIMER REC] Recording or While the [TIMER REC] Recording or While the [TIMER REC] g g g
Indicator is On or Blinking. Indicator is On or Blinking. g g Indicator is On or Blinking.
• Press [STANDBY-ON] to turn on the unit. Press [DVD
on the remote control to choose DVD mode. Then
continue with the other DVD features as described in
this manual.
gram g
] on the
g g g g
g g g
Operates as Follows: p
] to activate
] to activate the VCR function again.
ng is Com g p p p pleted.
y g
g. g
]
21