EURODESK SX4882 Important safety instructions 7) Do not block any ventilation openings. Install in accor- dance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Architecture 1.2.1 Shipment The EURODESK SX4882 is a hybrid SPLIT/INLINE console. Input channels cover most of the surface from the left, while the outputs Your product was carefully packed at the factory to ensure safe to tape are to the right. Tape monitor returns, however, are housed transport.
Channel strip to the main mix. On the EURODESK SX4882 the 24 INPUT + OUTPUT (I/O or “normal”) channels cover most of the console. Most of each strip In addition to switchable PFL/SOLO metering, a couple of LEDs...
EURODESK SX4882 Main equalizer Fig. 3.4: Aux sends For almost all FX SEND purposes, you will want auxes to be post fader, so that when a fader level is adjusted, any reverb send from that channel follows the fader. Otherwise, when the fader is pulled down, the reverb Fig.
EURODESK SX4882 Fig. 3.6: B-channel Inserts Insert points are useful for adding dynamic processing or equal- ization to a channel, subgroup or the mix. Unlike reverbs, etc., which are usually added to the dry signal, dynamic processing is normally applied across an entire signal. Here, an aux send would be inappropriate.
Using insert to add channel EQ to subgroup out- put (while keeping the number of line inputs unchanged!) Direct outputs Each of the 24 main channels on the EURODESK SX4882 has its own DIRECT OUTPUT, which is taken from a point immediately Subgroup and direct outputs...
EURODESK SX4882 after the fader (i.e. post EQ and after the aux sends, see block 6.1.2 Aux returns schematics). This can feed a tape track directly without having to Next to the aux sends are the stereo aux returns (see fig. 6.3).
EURODESK SX4882 As always, there are exceptions to the above rule. Some If MIX-B is assigned to the main mix (S48 DOWN), do not short stereo delay effects (say 30 ms to L, 50 ms to listen to MIX-B (S83) and the main mix (S82) simultane- right) cause a psychoacoustic effect where the earlier ously.
1, separate headphones distribution amplifier like our BEHRINGER aux 2, subgroups, and phones and studio (S96 to S99). POWERPLAY PRO HA4400. This can offer the added advantage Complex headphone or stage monitoring networks could be of independent headphones level control for every performer.
Rear panel Expander port bus inputs If you want to add another console to your EURODESK SX4882, the expander port bus inputs give access to all subgroups, auxes and mix busses via an array of 1/4" jacks, situated top left on the Fig.
Page 13
EURODESK SX4882 Fig. 7.9: MIX-B operating level switch and phantom power switch Subgroup outputs/tape sends The eight subgroups are each connected to two stereo jack sock- ets, for easy patching into 16 track recording systems (or 24 track, if you use Y-adaptors). Once again, the operating level is switchable between +4 dBu and -10 dBV in two banks of (2x) 4.
EURODESK SX4882 Connector pinout You will need a lot of cables for a lot of purposes. Here’s how they should look: ¼" mono (TS) plugs You'll need this kind for: Headphones You'll need this kind for: Expander Port Bus Inputs...
Unlike everything else, these operate at a level several orders of magnitude lower than line (+4 dBu or -10 dBV). It is best to plug microphones directly into the EURODESK SX4882, or via special Fig. 8.3: Example of patchbay configurations XLR-type wall boxes connected to the EURODESK microphone inputs by a good quality balanced (2-core + screen) multicore.
Q’s actually occurs in the audible spectrum, below 16 If you’re really serious about hum levels, you could run balanced to 18 kHz. For example if the BEHRINGER EQ is boosted by +15 lines wherever appropriate. The earth wiring scheme would be the dB at 20 kHz, the amount of boost at 10 kHz will be 3 dB.
Balanced inputs and outputs are offered on most audio connec- hitting 0 dB, then it must be coming from the aux send amp or the tions on the EURODESK SX4882 (inserts and direct outs being FX unit. If PFL on the aux send reveals nothing amiss, turn down the major exceptions).
EURODESK SX4882 for some pots, e.g. master aux sends, is unity gain. However, some settings, such as selecting PRE or POST for channel aux sends and whether TAPE or MIC/LINE is flipped onto B-channel etc. will depend on the operating environment, whether in a MIDI or A/V suite, 24-track studio or live venue, or even just on the engineer’s preferred way of working.
EURODESK SX4882 14.1 Sends Fig. 14.4: Subgroup-driven auxless headphones mix Fig. 14.1: Send routing This configuration does not allow for anything coming in on B-channels to be sent to headphones. If you need to do this, S76 In a dance production, effects are often of paramount importance must also be depressed.
EURODESK SX4882 14.5 Mixdown The following example covers a rock band with drums, bass, two guitars, percussionist, brass section, lead and backing vocals. The situation here is no different from record, really, save that the In the real world, you’ll hardly ever be taking all these artists at...
EURODESK SX4882 Choose to send to subgroups 7 and 8 from channels Chan- Wedges / which are routed to tape from their DIRECT OUT. Source nels monitoring Otherwise CHANNEL PAN, which will already have Subgroups 1 Aux send 1 been set for recording via another group, is unlikely...
EURODESK SX4882 Live concert with 24-track recording Chan- Source F.O.H. Wedges Infills nels Stereo (quadraphonic) P.A. with sidefills, three infills, two wedge Subgroups 1/2, mixes, four FX and simultaneous 24-track recording. Kick MIX-B 3/4 and 7/8 Chan- Aux send Aux send...
PFL/SOLO buses. Since the nominal internal operating level Sometimes you want to play back from one or more tracks, route of your EURODESK SX4882 is 0 dB, and that at the jack outputs the signals to a new track or pair of tracks, and re-record. This +4 dB, the sends from the outputs of console 2 must be attenuated process is commonly referred to as bouncing.
Fig. 23.5: Modifications MIX-B source > post fader BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.
BEHRINGER logo, JUST LISTEN and EURODESK) mentioned belong to their respective owners, and such use neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the trademark owners with BEHRINGER. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein.
= Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. = Consult the dealer or an experienced radio/TV technician for help. Important information: Changes or modifications to the equipment not expressly approved by BEHRINGER USA can void the user’s authority to use the equipment.