L Unit - Marantz ER2500 User Manual

3. Close until it clicks.
UNIT
he remote
e ER2500
ransmitter
SENSOR
m, remote
Notes:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
CAUTIONS ON BATTERIES
• Use "AAA" type batteries in this remote control
unit.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do so
ote control in the proper direction, following the + and - marks
so be sure in the remote control unit's battery compartment.
otice that
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction's rules that apply in your country
or area.
ype) with
PROGRAMMING THE REMOTE CONTROL
UNIT
The remote control unit RC2500ER must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 3-
digit code or by scanning the codes until the correct
one is found. We recommend to using the 3-digit
code. This mode is faster and more reliable. The
code scanning method should be used only if you
cannot find the code for one of your appliances.
The codes are listed at the end of this book.
Important:
• Use the remote control buttons for programming,
not the buttons of the receiver or other appliances.
• Some codes may be not match your equipment.
In this case, your equipment cannot be controlled
with this remote controller.
• If the battery life of remote controller is lost, a
program code will be reset from a memory.
04.8.26, 4:29 PM
STANDBY/ON SLEEP
DVD TUNER TV TV POWER
VCR DSS A/D TV-INPUT
1 2 3
TV-VOL
4 5 6
7 8 9
SURROUND DIMMER TV-CH
0
PROGRAMMING WITH THE 3-DIGIT CODE
VOLUME
STANDBY/ON STANDBY/ON SLEEP SLEEP
DVD-SET UP DVD-SET UP TOP MENU TOP MENU
2
2
ENTER ENTER
DVD DVD TUNER TUNER TV TV TV POWER TV POWER
RETURN RETURN MENU MENU
VCR VCR DSS DSS A/D A/D TV-INPUT TV-INPUT
TUNE PRESET TUNE PRESET BAND BAND TUNE MODE TUNE MODE
1 1 2 2 3 3
T.CLR T.CLR RDS RDS FM MODE FM MODE MEMORY MEMORY
3 TV-VOL TV-VOL
4 4 5 5 6 6
S.TITLE S.TITLE AUDIO AUDIO ANGLE ANGLE ZOOM ZOOM
7 7 8 8 9 9
REPEAT REPEAT
PRG PRG 1/ALL 1/ALL A-B A-B RANDOM RANDOM CLR CLR
SURROUND SURROUND DIMMER DIMMER TV-CH TV-CH
0 0
NTSC/PAL NTSC/PAL T.TONE T.TONE SPK SET SPK SET TONE TONE NIGHT NIGHT
VOLUME VOLUME
RC2500ER RC2500ER
DVD-SET UP DVD-SET UP TOP MENU TOP MENU
ENTER
RETURN MENU
1. Turn on the appliance which should be controlled.
2. Press and hold down the ENTER button and
TUNE PRESET BAND TUNE MODE
press TV button until the indicator lamp blinks
T.CLR RDS FM MODE MEMORY
twice.
S.TITLE AUDIO ANGLE ZOOM
3. Press the 3-digit code for appliance. (code
REPEAT
PRG 1/ALL A-B RANDOM CLR
table at the end of this book)
• If the 3-digit code is not pressed with 10 NTSC/PAL T.TONE SPK SET TONE NIGHT
seconds, this programming function is
canceled.
4. When the procedure is successful, the indicator
RC2500ER
lamp will blink twice.
Note:
• If the indicator lamp blinks in 1 second, program
code is wrong.
• If the indicator lamp did not blink twice, then
repeat steps 1 through 2 and try entering the
same code again.
9