Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Electrolux Vent Hood
Summary of Contents for Electrolux Vent Hood
-
Page 1: Installation Instructions
Use & Care Guide Installation Instructions Vent Hood 316495008 - 09/2007... -
Page 2: Table Of Contents
Please read and save this guide Thank you for choosing Electrolux, the new premium brand in home appliances. This Use & Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new appliance. -
Page 3: Safety
Safety Important Safety Instructions Read all instructions before using this appliance. Save these instructions for future reference. Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type. - Page 4 Safety 6. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes over- heated. The motor will restart when it cools down. If the motor continues to shut off and restart, have TO REDUCE THE RISK OF INJURY TO PERSONS the hood serviced.
-
Page 5: Verify Package Contents
Verify package contents Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Support Frame 1 - Parts Bag containing: 1 - Support Frame Bracket 1 - Discharge Collar 4 - Mounting Screws (6 x 70) 16 - Mounting Screws (3,9 x 9,5mm Pan Head) 4 - Washers D.6.4mm 6 - Serrated Washers... -
Page 6: Installation
Installation Install the ductwork ROOF CAP ROUND To reduce the risk of fire, use only metal DUCT ductwork. 1. Decide where the ductwork will run between the hood and the outside. D E C O R A - ROUND T I V E ELBOW F L U E EAVE... -
Page 7: Install Support System
Installation Install support system 1. At hood location, install 2 X 4 cross framing between DRYWALL CROSS FRAMING ceiling joists using dimensions shown. ” 2. Finish the ceiling surface. Be sure to mark the location of the ceiling joists and cross framing. 3. -
Page 8: Prepare The Hood
Installation recirculation plenum. Fig.6. Prepare the hood 4. Mount the 6”/5” adapter above hood. Fig. 7. NON-DUCTED NOTE RECIRCULATION PLENUM On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and decorative flues, prior to final installation. -
Page 9: Connect Decorative Flue
Installation Connect decorative flue Install the hood 1. Secure the upper flue to the upper support frame with the mounting screws (3.9x9.5mm). Fig. 8. NOTE 2. Insert the lower flue moving it completely towards the top and fix it temporarily with a tape. Fig. 9. At least three people will be required to mount the hood. -
Page 10: Connect Ductwork
Installation Connect ductwork Install filters (DUCTED AND NON-DUCTED HOODS) (DUCTED HOODS ONLY) 1. To remove the GREASE filters, pull the metal latch 1. Use 6" round metal duct to connect the discharge tab outside and unlock the filter. collar on the hood to the ductwork above (Fig. 11). 2. -
Page 11: Maintenance
Maintenance Proper maintenance of the Range Hood will assure proper performance of the unit. Grease filters Hood cleaning Stainless steel is one of the easiest materials to keep The grease filters should be cleaned when the filter clean. Occasional care will help preserve its fine reset switch will be illuminated. -
Page 12: Operation
Operation Controls display delay light filter fan speed on/off shut switch reset switches switches switch Dead-front mode Push this switch once to turn the timer Off. Filter reset switch When the filter switch is illuminated, it is necessary to clean the GREASE FILTERS. Once the grease filters are cleaned and installed, press in and hold the “filter Stand-by mode reset switch”... -
Page 13: Halogen Bulbs
Operation Halogen bulbs Fuse replacement This range hood requires four halogen bulbs (max 20W, 12V, Type T3 bulb, G4 Base). Halogen Bulb Key : 5304454951 SWITCH OFF THE ELECTRICITY SUPPLY. Remove the grease filters. Open the fuse box. ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CARRYING OUT ANY OPERATIONS ON THE Replace with the same type of fuse (5x20mm, 4A, 125V). -
Page 14: Wiring
Wiring This range hood must be properly grounded. Improper grounding can result in a risk of electric shock. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. Turn off electrical power at service entrance before wiring. 1. -
Page 15: Warranty Information
This warranty only applies in the 50 states of the U.S.A., Puerto Rico and Canada. Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidation Industries, Inc. - Page 16 04307839/2S...