Heat & Glo HST-48D Owner's Manual page 44

B. Chimney Components
The following pictures show only those chimney components which may be safely used with this fireplace.
Catalog #
US CAN
CAK5A CAK5A
ID4 ID4
UD4 UD4
SL1106 SL406
SL1112 SL412
SL1118 SL418
SL1136 SL436
SL1148 SL448
SL11 SL4
SL1130 SL430
FS538 FS538
FS540 FS540
AS10 AS10
JB577 JB577
CB576 CB576
RF570 RF570
RF571 RF571
TR11 TR444
TR11T TR442
TCT1175
ST1175 ST475
DTO134
DTO146
DTS134
DTS146
CT56 CT56
LDS33 LDS33
LDS46 LDS46
LDS-BV LDS-BV
CT-11A n/a Adapter-May be used with the following Copper Caps
n/a
n/a
14 in.
(356 mm)
5-1/4 in.
(133 mm)
13 in.
(330 mm)
CAK5A Chimney Air Kit
44
Description
Chimney Air Kit
Insulated Duct/Outside Air
Uninsulated Duct/Outside Air
Chimney Section - 6 in. (152 mm) long
Chimney Section - 12 in. (305 mm) long
Chimney Section - 18 in. (457 mm) long
Chimney Section - 36 in. (914 mm) long
Chimney Section - 48 in. (1219 mm) long
Chimney Stabilizer
Chimney Offset/Return - 30 deg
Ceiling Firestop - Straight
Ceiling Firestop - 30 deg
Straight Attic Insulation Shield, 24 in. (610 mm)
Chimney Joint Band
Chimney Bracket
Roof Flashing - Flat to 6/12 Pitch
Roof Flashing - 6/12 to 12/12 Pitch
Round Termination Cap
Round Telescoping Termination Cap
Terra Cotta Termination Cap
Square Termination Cap
Short Octagon Decorative Cap
Tall Octagon Decorative Cap
Short Square Decorative Cap
Tall Square Decorative Cap
Chase Top
Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)
Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)
Decorative Shroud - 26 in. x 26 in.
(660 mm x 660 mm)
Field Constructed Shrouds (See "Woodburning
Termination Cap")
CT-Series
DT-Series
14 in.
(356 mm)
4 in. (102 mm)
Heat & Glo • HST-48D US-CAN • 4012-040 • Rev K • 3/12
ID4 Insulated Duct
42 in.
(1067 mm)
UD4 Uninsulated Duct
42 in.
(1067 mm)
11 in.
(279 mm)
Chimney Sections
Catalog #
US CAN in
SL1106 SL406 6
SL1112 SL412 12
SL1118 SL418 18
SL1136 SL436 36
SL1148 SL448 48
A = Actual Length
B = Effective Length (length of
chimney part after it has
been snapped to another)
SLA10 Adapter
SL11 - 11 in. (279 mm)
20-3/4 in.
(527 mm)
SL11/SL4 Vent Stabilizer
4 in. (102 mm) i.d.
4 in. (102 mm) i.d.
A
13 in.
(330 mm)
B
A B
mm in mm
152 4-3/4 121
305 10-3/4 273
457 16-3/4 425
914 34-3/4 883
1219 46-3/4 1187
18 in.
(457 mm)
Inside Diameter
SL4 - 10 in. (254 mm)
Outside Diameter
13 in. (330 mm)