Samsung FP-T5084 Owner's Instructions Manual page 95

Press the'" or
~
button to select the antenna
connection, then press the ENTER button.
• Air: "Air" antenna signal.
Cable: "Cable" antenna signal.
Air+Cable: "Air" and "Cable" antenna signals.
Press the. or T button to select digital or analog
channels, then press the ENTER button. You can
select the correct signal source among STD, HRC
and IRC by pressing the. or T button, then press
the ENTER button.
• If you have Digital cable TV, select the signal
source for both Analog and Digital.
• STD, HRC, and IRC identify various types of
cable TV systems. Contact your local cable
com(jany to identify the type of cable system that
exists in your particular area.
At this point the signal source has been selected.
Press the ~ button to select Start, then press the
ENTER button to start the auto program.
The TV begins memorizing all available stations.
Press the ENTER button at any time to interrupt the
memorization process.
When pressing the ENTER button during a storing
process, the message Stop Auto Program? is
displayed.
Select Yes by pressing the'" or ~ button.
Press the EXIT button to exit.
• The TV must be connected to an antenna/cable
in order to receive digital TV signals. Even if a
particular channel is deleted from the memory,
you can always tune to that channel directly by
using the number buttons on the remote control.
Picture Con
0
Your TV has three automatic picture settings ("Dynamic",
"Standard", and "Movie") that are preset at the factory. You
can activate either Dynamic, Standard, or Movie by making a
selection from the menu.
Please be aware that the best picture on this TV will be
obtained from High Definition (HD) sources such as Digital
cable or DVD players.
O Press the MENU button.
Press the'" or T button to select Picture, then press
the ENTER button.
fA
Press the ENTER button again to select Mode.
Press the ENTER button.
Press the. or T button to select Dynamic,
Standard, or Movie, then press the ENTER button.
• Choose Dynamic to increase the clarity and
sharpness of the picture.
• Choose Standard for general TV watching mode.
• Choose Movie when watching movies.
Press the EXIT button to exit.
English. 12
Press the'" or
~
button to select the antenna
connection, then press the ENTER button.
• Air: "Air" antenna signal.
Cable: "Cable" antenna signal.
Air+Cable: "Air" and "Cable" antenna signals.
Press the. or T button to select digital or analog
channels, then press the ENTER button. You can
select the correct signal source among STD, HRC
and IRC by pressing the. or T button, then press
the ENTER button.
• If you have Digital cable TV, select the signal
source for both Analog and Digital.
• STD, HRC, and IRC identify various types of
cable TV systems. Contact your local cable
com(jany to identify the type of cable system that
exists in your particular area.
At this point the signal source has been selected.
Press the ~ button to select Start, then press the
ENTER button to start the auto program.
The TV begins memorizing all available stations.
Press the ENTER button at any time to interrupt the
memorization process.
When pressing the ENTER button during a storing
process, the message Stop Auto Program? is
displayed.
Select Yes by pressing the'" or ~ button.
Press the EXIT button to exit.
• The TV must be connected to an antenna/cable
in order to receive digital TV signals. Even if a
particular channel is deleted from the memory,
you can always tune to that channel directly by
using the number buttons on the remote control.
Picture Con
0
Your TV has three automatic picture settings ("Dynamic",
"Standard", and "Movie") that are preset at the factory. You
can activate either Dynamic, Standard, or Movie by making a
selection from the menu.
Please be aware that the best picture on this TV will be
obtained from High Definition (HD) sources such as Digital
cable or DVD players.
O Press the MENU button.
Press the'" or T button to select Picture, then press
the ENTER button.
fA
Press the ENTER button again to select Mode.
Press the ENTER button.
Press the. or T button to select Dynamic,
Standard, or Movie, then press the ENTER button.
• Choose Dynamic to increase the clarity and
sharpness of the picture.
• Choose Standard for general TV watching mode.
• Choose Movie when watching movies.
Press the EXIT button to exit.
English. 12