Automatically Tuning The Tv Using The Remote Control - Sony TRINITRON KV-21FX20A Service Manual

First Time Operation - Basic Presetting

Automatically Tuning the TV using the Remote Control

You need to tune the TV to receive channels (TV Broadcast). By following the instructions below, this TV automatically
searches and stores all available channels for you.
After having selected the language, a new menu appears automatically on the TV screen asking you to automatically tune
the TV. However, if you need to change or repeat the tuning afterwards (e.g. when you move house), select the menu
AUTO PROGRAMME in the (SET UP) menu and proceed in the same way as described below in step 1 or, please refer
to the section "Automatically Tuning the TV using the TV buttons" of this instruction manual.
1
Press the OK button on the remote control to select YES.
A new menu appears automatically on the screen asking you to
check that the antenna is connected.
1 2 3
2
Confirm that the antenna is connected and then press the OK
button.
4 5 6
7 8 9
0
The automatic tuning starts and the message "Searching..." flashes
on the screen.
MENU
This procedure could take some minutes.
K
When the automatic tuning is finished, the Programme Sorting menu
appears on the TV screen.
PROGR
Notes: • To stop the automatic tuning, press the MENU button.
• If you stop the automatic tuning by pressing the MENU
button, the Programme Sorting menu does not appear
RM 887
automatically on the TV screen.
S
10
First Time Operation - Basic Presetting
First Time Operation - Basic Presetting
Changing the Programme Order of the TV channels
After all available channels (TV Broadcast) are captioned and stored, a new menu appears automatically on the screen to
change the order in which the channels appear on the screen.
However, if you wish to rearrange the order of the channels afterwards, select the menu PROGRAMME SORTING in the
(SET UP) menu and proceed in the same way as described in the b) section of this chapter.
Do you want to start
automatic tuning?
Do you want to start
automatic tuning?
YES
YES
NO
NO
1 2 3
Please confirm that
antenna is connected
CONFIRM
4 5 6
7 8 9
AUTO PROGRAMME
0
01
PROGRAMME:
SYSTEM: B/G
MENU
CHANNEL: C 21
Searching...
K
PROGRAMME SORTING
PROGRAMME: 01 03
CONFIRM
Select Channel: PROGR
Select new position:
PROGR
Confirm:
Exit:
MENU
RM 887
S
a) If you do not wish to change the channel order:
1
Press the MENU button to exit and return to the normal TV screen.
Your TV is now ready for use.
b) If you wish to change the channel order:
1
Press the PROGR or button until the channel (TV Broadcast) you
wish to rearrange appears on the screen.
2
Press the or button to select the new programme number
position for your selected channel (TV Broadcast), then press the
OK button.
The word CONFIRM is highlighted for a few seconds to
confirm that the new programme position is stored.
3
Repeat steps 1 and 2 if you wish to change the order of the other
channels on your TV.
4
Press the MENU button to exit and return to the normal TV screen.
Your TV is now ready for use.
PROGRAMME SORTING
PROGRAMME: 01 03
PROGRAMME SORTING
CONFIRM
PROGRAMME: 01 03
CONFIRM
Select Channel: PROGR
Select Channel: PROGR Select new position:
Confirm:
Select new position: Exit: MENU
Confirm:
Exit: MENU
PROGRAMME SORTING
PROGRAMME: 01 03
CONFIRM PROGRAMME SORTING
PROGRAMME: 01 03
CONFIRM
Select Channel: PROGR
Select new position:
Select Channel: PROGR
Confirm:
Exit: MENU
Select new position:
Confirm:
Exit:
MENU
PROGRAMME SORTING
PROGRAMME: 02 04
CONFIRM
Select Channel: PROGR
Select new position:
Confirm:
Exit:
MENU
11
First Time Operation - Basic Presetting