Advertisement

SERVICE MANUAL
Ver 1.1 2001.04
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.6 - 108 MHz
CND, E92, MX model:
AM: 530 - 1,710 kHz
E4, SP, AR model
AM: 531 - 1,602 kHz (9 kHz step)
AM: 530 - 1,610 kHz (10 kHz step)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Sony Corporation
9-873-061-32
2001D0400-1
Personal Audio Company
© 2001.4
Shinagawa Tec Service Manual Production Group
CFD-S36
Model Name Using Similar Mechanism CFD-S22/S32
CD
CD Mechanism Type
Section
Optical Pick-up Name
Model Name Using Similar Mechanism CFD-V5
TC
Section Tape Transport Mechanism Type

SPECIFICATIONS

Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10,000 Hz
General
Speaker
Full range: 10 cm dia.,
3.2 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
Power output
2.3 W + 2.3 W (at 3.2 ohms, 10 %
harmonic distortion in AC operation)
Power requirements
For CD radio cassette-corder:
CND, E92, MX model:
120 V AC, 60 Hz
SP, AR model:
230 V AC, 50 Hz
E4 model:
110 - 120 V/220 - 240 V AC selectable, 50/60 Hz
9 V DC, 6 size D (R20) batteries
For remote control
3 V DC, 2 size AA (R6) batteries
CD RADIO CASSETTE-CORDER
Canadian Model
E Model
KSM-213CDP
KSS-213C
MF-V5-117
– Continued on next page –
1

Advertisement

Table of Contents
loading

Summary of Contents for Sony CFD-S36

  • Page 1: Specifications

    Compact disc digital audio system 4-track 2 channel stereo Laser diode properties Fast winding time Material: GaAlAs Approx. 120 sec. with Sony cassette C-60 Wave length: 780 nm Frequency response Emission duration: Continuous TYPE I (normal): 80 - 10,000 Hz Laser output: Less than 44.6 µW...
  • Page 2 LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Table Of Contents

    CFD-S36 TABLE OF CONTENTS 1. SERVICING NOTES ............4 2. GENERAL ................5 3. DISASSEMBLY 3-1. Cabinet (Front) Sub Assy ............ 6 3-2. Wires ................... 7 3-3. Power (1) Board, Power (2) Board ........7 3-4. Voltage Select Board ............8 3-5.
  • Page 4: Servicing Notes

    CFD-S36 SECTION 1 SERVICING NOTES LASER DIODE AND FOCUS SEARCH OPERATION CHUCK PLATE JIG ON REPAIRING CHECK 1. Turn ON the POWER button and press FUNCTION button to On repairing CD section, playing a disc without the lid (CD), use CD position.
  • Page 5: General

    CFD-S36 SECTION 2 GENERAL This section is extracted from instruction manual. Location of controls PLAY REW FF STOP/EJECT PAUSE VOLUME +,– Number buttons for CD/RADIO DIRECT OPERATION Tape Z PUSH compartment OPEN/CLOSE MEGA Xpand SLEEP POWER compartment MEGA BASS TAPE RADIO BAND•...
  • Page 6: Disassembly

    CFD-S36 SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. Cabinet (Upper) Assy Cabinet (Front) Sub Assy Wires Main Board Power (1) Board, Power (2) Board Voltage Select Board Tape Mechanism Block Holder Assy, Cassette PRE Board...
  • Page 7: Wires

    CFD-S36 3-2. WIRES Put flat cable and wires between the cabinets and push them in the grooves located at A to E in the figure to prevent disconnection before assembling the set. CABINET (FRONT) from MAIN board CABINET (REAR) from speaker from CONTROL (1) board 3-3.
  • Page 8: Voltage Select Board

    CFD-S36 3-4. VOLTAGE SELECT BOARD (E4 model only) • Abbreviation E4 : AC 110-120V/220-240V area in E model 2 VOLTAGE SELECT board (E4 model only) 1 BVTP 3x10 3-5. CABINET (UPPER) ASSY 4 BVTP 3x12 3 holder assy, cassette 6 BVTP 3x12...
  • Page 9: Main Board

    CFD-S36 3-6. MAIN BOARD 3 CNP702 6 BVTP 3x10 5 BVTP 3x10 8 MAIN board 2 connector (S801) 1 terminal, antenna 7 CNP301 4 CNP302 3-7. CD MECHANISM BLOCK 1 PWH 2.6x10 2 PWH 2.6x10 3 CD mechanism block (KSM-213CDP)
  • Page 10: Tape Mechanism Block

    CFD-S36 3-8. TAPE MECHANISM BLOCK 1 BVTP 3x10 2 BVTP 3x10 3 tape mechanism block (MF-V5-117) 3-9. HOLDER ASSY, CASSETTE 1 BVTP 3x10 2 DAMPER 4 holder assy, cassette...
  • Page 11: Pre Board

    CFD-S36 3-10. PRE BOARD 1 BVTT 2x6 4 PRE board 3 Removal the solders. claw claw 3-11. BELT, M801 (CAPSTAN/REEL MOTOR), HRP301 (HEAD, MAGNETIC) 6 HRP301 (head, magnetic) 1 screws B 2.6 × 5 mechanism deck 5 claws 4 M801...
  • Page 12: Optical Pick-Up

    CFD-S36 3-12. OPTICAL PICK-UP 2 claws 3 cover, CD 9 optical pick-up 1 claws 5 gear (A) 4 claw 6 claw 8 sled shaft...
  • Page 13: Mechanical Adjustments

    CFD-S36 SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION TAPE SECTION 0 dB = 0.775 V 1. Clean the following parts with a denatured-alcohol-moistened swab : • Standard Output Level record/playback head pinch roller Output terminal HP OUT erase head rubber belts 32 Ω...
  • Page 14: Tuner Section

    CFD-S36 TUNER SECTION 0 dB = 1 µV FM IF ADJUSTMENT • FM Section Adjust for a maximum reading on level meter. Setting: RADIO (BAND) button: FM 10.7 MHz FM RF signal generator FM FREQUENCY COVERAGE TP (JW2) ADJUSTMENT 0.01 µF Frequency Display 87.5 MHz...
  • Page 15: Cd Section

    CFD-S36 Adjustment Location: ADJUSTMENT ADJUSTMENT CT1, L1 TP (JW1) FREQUENCY TRACKING – MAIN board (component side) – COVERAGE ADJUSTMENT ADJUSTMENT TP (VT) (CONDUCTOR SIDE) CT3, L3 TRACKING ADJUSTMENT FREQUENCY COVERAGE ADJUSTMENT CD SECTION CD section adjustments are done automatically in this set.
  • Page 16: Diagrams

    CFD-S36 SECTION 6 DIAGRAMS 6-1. IC PIN DESCRIPTION • IC802 uPD789477-907 (SYSTEM CONTROLLER) Pin No. Pin Name Pin Description 1, 2 — Not used. (Open) 3 – 5 VLC2 – 0 LCD drive voltage output 6 – 9 COM0 – 3 LCD drive common output 10 –...
  • Page 17: Circuit Boards Location

    CFD-S36 Pin No. Pin Name Pin Description Main system oscillation output (4.19 MHz) System reset input ISS1 ISS1 output Not used. (Open) ISS2 ISS2 output Not used. (Open) EEPROM clock output EEPROM input/output 6-2. CIRCUIT BOARDS LOCATION POWER (1) board...
  • Page 18: Block Diagram - Cd Section

    CFD-S36 6-3. BLOCK DIAGRAM — CD SECTION — CD BOARD MAIN BOARD (1/2) CNP701 CD_IN_ L CNP702 (2/2) CNP804 (2/2) CNP806 (1/3) LCHO INTERPOLATION SLICE ERROR MUTE DIGITAL FIN2 EFMIN LEVEL CORRECTION & FILTER CONTROL AUDIO CD RCHO ATTENUATION &...
  • Page 19: Block Diagram - Main Section

    CFD-S36 6-4. BLOCK DIAGRAM — MAIN SECTION — PRE BOARD MAIN BOARD (2/2) R.RO R.IN R.LINE CD_IN_R VOLUME/SOUND CONTROLLER REC/PB POWER AMP CNP301 CNP806 IC302 PRE AMP IC304 R-CH (3/3) (3/3) CNP301 (1/3) IC301 L.RO J321 ALC 2 LINE CD_IN_L L.LINE...
  • Page 20: Printed Wiring Board - Cd Section

    CFD-S36 6-5. PRINTED WIRING BOARD — CD SECTION — • Refer to page 17 for Circuit Boards Location. THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) Common Note on Schematic Diagrams: •...
  • Page 21: Schematic Diagram - Cd Section

    CFD-S36 6-6. SCHEMATIC DIAGRAM — CD SECTION — • Refer to page 20 for Common Note on Schematic Diagrams and page 31 for IC Block Diagrams. (Page 24) IC B/D IC B/D • Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 22: Printed Wiring Boards - Main Section

    CFD-S36 6-7. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. • Semiconductor Location Ref. No. Location ANT1 MAIN BOARD TELESCOPIC ANTENNA (Page 20)
  • Page 23: Schematic Diagram - Main Section (1/4)

    CFD-S36 6-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 20 for Common Note on Schematic Diagrams and page 32 for IC Block Diagrams. IC B/D IC B/D (Page 24) • Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 24: Schematic Diagram - Main Section (2/4)

    CFD-S36 6-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 20 for Common Note on Schematic Diagrams and page 33 for IC Block Diagrams. IC B/D (Page 26) (Page 25) (Page 21) • Waveforms 2V/div 10µsec/div 2V/div 10µsec/div •...
  • Page 25: Schematic Diagram - Main Section (3/4)

    CFD-S36 6-10. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 20 for Common Note on Schematic Diagrams and page 33 for IC Block Diagrams. IC B/D (Page 30) (Page 24) • Voltage is dc with respect to ground under no-signal (detuned) condition.
  • Page 26: Schematic Diagram - Main Section (4/4)

    CFD-S36 6-11. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 20 for Common Note on Schematic Diagrams and page 33 for IC Block Diagrams. IC B/D (Page 24) • Waveform 0.1V/div 5µsec/div • Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 27: Printed Wiring Boards - Control Section

    CFD-S36 6-12. PRINTED WIRING BOARDS — CONTROL SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. (Page 22) MAIN BOARD CNP805 CONTROL ( 1 ) BOARD VOLUME –...
  • Page 28: Schematic Diagrams - Control Section

    CFD-S36 6-13. SCHEMATIC DIAGRAMS — CONTROL SECTION — • Refer to page 20 for Common Note on Schematic Diagrams. (Page 24) • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...
  • Page 29: Printed Wiring Boards - Power Supply Section

    CFD-S36 6-14. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. BATTERY TERMINAL ( 2 ) BOARD BATTERY TERMINAL ( 1 ) BOARD DRY BATTERY SIZE "...
  • Page 30: Schematic Diagrams - Power Supply Section

    CFD-S36 6-15. SCHEMATIC DIAGRAMS — POWER SUPPLY SECTION — • Refer to page 20 for Common Note on Schematic Diagrams. (Page 25)
  • Page 31: Ic Block Diagrams

    CFD-S36 • IC Block Diagrams IC701 LC78645E (CD Board) 78 77 76 75 74 73 72 71 69 68 67 66 65 64 63 62 61 FIN1 – FIN2 – TIN1 TBAL – – TIN2 – – TBAL – RFMON...
  • Page 32 CFD-S36 IC702 BA6998FP-E2 (CD Board) IC1 TA2149N (MAIN Board) GND1 FM RF-OUT FM RF SP– D.BUFF VCC1 FM RF-IN SL– AM RF-IN D.BUFF AM LOW CUT LEVEL D.BUFF SHIFT MIX OUT FM OSC D.BUFF SPIN LEVEL SHIFT AM OSC BUFF...
  • Page 33 CFD-S36 IC803 BR24C01AF-WE2 (MAIN Board) IC302 M62429P (MAIN Board) VIN2 VOUT2 CLOCK 1K BIT EEPROM ARRAY VR 2 8BIT 7BIT VOL AMP 2 VREF LOGIC SLAVE • WORD CONTROL ADDRESS DATA ADDRESS 7BIT VOL AMP 1 DECODER REGISTER REGISTER REF AMP...
  • Page 34: Exploded Views

    CFD-S36 SECTION 7 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety.
  • Page 35: Cabinet (Rear) Section

    CFD-S36 7-2. CABINET (REAR) SECTION F902 T901 S901 E4 Model CND, E92, SP, MX, AR Model The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety.
  • Page 36: Cabinet (Upper) Section

    CFD-S36 7-3. CABINET (UPPER) SECTION ANT1 S801 MF-V5-117 KSM-213CDP LCD801...
  • Page 37 CFD-S36 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 A-3062-383-A MAIN BOARD, COMPLETE (SP) 3-224-370-51 LID (CD) (CND,E4,E92,MX) * 101 A-3062-384-A MAIN BOARD, COMPLETE (AR) 3-224-370-61 LID (CD) (SP,AR) * 101 A-3062-385-A MAIN BOARD, COMPLETE (E4)
  • Page 38: Tape Mechanism Section-1

    CFD-S36 7-4. TAPE MECHANISM SECTION-1 (MF-V5-117) HRP301 HE301 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-933-010-01 SPRING (S/P), TORSION * 162 3-008-587-01 SLIDER (STOP) 3-933-025-01 SPRING (P), TORSION * 163 3-008-591-01 SLIDER (PAUSE) 3-040-857-01 LEVER (P)
  • Page 39: Tape Mechanism Section-2

    CFD-S36 7-5. TAPE MECHANISM SECTION-2 (MF-V5-117) S802 M801 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-933-029-01 LEVER, ERASING PREVENTION X-3377-877-2 FLYWHEEL ASSY 3-933-182-01 SPRING, CASSETTE 3-932-993-01 CHASSIS, OUTSERT 3-932-995-01 GEAR (MID) 3-343-358-01 RING, RETAINING X-3371-667-1 CLUTCH ASSY...
  • Page 40: Optical Pick-Up Section

    CFD-S36 7-6. OPTICAL PICK-UP SECTION (KSM-213CDP) not supplied not supplied M701 M702 The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité.
  • Page 41: Electrical Parts List

    CFD-S36 SECTION 8 BATTERY TERMINAL (1) ELECTRICAL PARTS LIST BATTERY TERMINAL (2) NOTE: The components identified by • Due to standardization, replacements in • Items marked “*” are not stocked since mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 42 CFD-S36 CONTROL (1) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R705 1-216-835-11 METAL CHIP 1/16W < RESISTOR > R706 1-216-841-11 METAL CHIP 1/16W R707 1-216-797-11 METAL CHIP 1/16W R401 1-216-819-11 METAL CHIP 1/16W R708 1-216-833-11 METAL CHIP...
  • Page 43 CFD-S36 CONTROL (2) CONTROL (3) MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-679-967-11 CONTROL (2) BOARD A-3062-383-A MAIN BOARD, COMPLETE (SP) A-3062-384-A MAIN BOARD, COMPLETE (AR) ****************** A-3062-385-A MAIN BOARD, COMPLETE (E4) < CONNECTOR >...
  • Page 44 CFD-S36 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-162-964-11 CERAMIC CHIP 0.001uF C331 1-104-664-11 ELECT 47uF 1-162-964-11 CERAMIC CHIP 0.001uF C332 1-126-963-11 ELECT 4.7uF 1-162-927-11 CERAMIC CHIP 100PF C333 1-126-963-11 ELECT 4.7uF 1-162-964-11 CERAMIC CHIP 0.001uF...
  • Page 45 CFD-S36 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRIMMER > JC306 1-216-864-11 SHORT JC307 1-216-864-11 SHORT 1-141-603-21 CAP, ADJ 20PF JC308 1-216-864-11 SHORT 1-141-601-21 CAP, ADJ 10PF < CABLE HOLDER > < DIODE >...
  • Page 46 CFD-S36 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-827-11 METAL CHIP 3.3K 1/16W R242 1-216-827-11 METAL CHIP 3.3K 1/16W 1-216-825-11 METAL CHIP 2.2K 1/16W R243 1-216-853-11 METAL CHIP 470K 1/16W 1-216-813-11 METAL CHIP 1/16W...
  • Page 47 CFD-S36 MAIN POWER (1) POWER (2) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R844 1-216-835-11 METAL CHIP 1/16W < CONNECTOR > R845 1-216-841-11 METAL CHIP 1/16W R846 1-216-821-11 METAL CHIP 1/16W * CNP901 1-815-551-11 PIN, CONNECTOR (PC BOARD) 3P...
  • Page 48 CFD-S36 VOLTAGE SELECT Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > 1-682-250-14 VOLTAGE SELECT BOARD (E4) ********************* CNP301 1-568-830-11 CONNECTOR, FFC 11P < SWITCH > < IC > 0 S901 1-552-921-00 SWITCH, POWER (VOLTAGE SELECTOR) (E4)
  • Page 49 CFD-S36 Ref. No. Part No. Description Remark ACCESSORIES & PACKING MATERIALS ******************************** 1-557-287-11 CORD, POWER (E92,MX) 1-569-008-21 ADAPTOR, CONVERSION (E4) 1-690-952-11 CORD, POWER (CND) 1-696-820-21 CORD, POWER (E4,SP) 1-783-952-11 CORD, POWER (AR) 3-027-153-11 LID, BATTERY CASE (for RMT-CS36A) 3-227-155-14 MANUAL, INSTRUCTION (ENGLISH)
  • Page 50 CFD-S36 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.

Table of Contents