COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-43 FACTORY MODEL: L1811SG MODEL: L1811S (L1811SG-VL) CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. L1811S...
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Total Period Video Active Time Front Porch Sync Duration Back Porch Sync Mode Resolution Frequency Clock Polarity Sort 31.469 640x350 25.175 70Hz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW L1811S Power Connect See Front Control Panel D-Sub Signal Connect Front Control Panel 1. Power ON/OFF Button 5. SELECT Button Use this button to turn the monitor on or off. Use this button to enter a selection in the On Screen Display. Use this button to scanning auto adjust.
DESCRIPTION OF BLOCK DIAGRAM 1. Video Controller Part & Display Data Transmitter Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixel clock. The pixel clock for each mode is generated by the PLL.
Power Board Block Diagram 50 ~ 60Hz 100KHz HVDC INPUT RECTIFIER ENERGY OUTPUT RECTIFIER COMPONENTS AND FILTER TRANSFER AND FILTER LINE 100 ~ 240V SIGNAL PWM CONTROL PHOTO-COUPLER COLLECT- CIRCUIT ISOLATION PRIMARY SECONDARY Operation description_Power 1. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
Enter. 1. Adjustment Start 1) Display any pattern at any Mode. 3. Adjustment for EDID 2) Run alignment program for L1811SG on the IBM 1) Use this procedure only when there is some compatible PC. probelm on EDID data. 3) Select EEPROM...
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J702 TROUBLE IN INPUT VOLTAGE POWER (12V) ? CHECK J702 TROUBLE IN 5V VOLTAGE POWER (5V) ? CHECK U203’s PIN 103. TROUBLE IN IS THIS PIN U203 or X201 OSCILLATED? TROUBLE SOMEWHERE ELSE...
Page 12
2. NO RASTER NO RASTER CHECK J703 PIN 1, 2 TROUBLE IN (12V) ? POWER CHECK TROUBLE IN J705 PIN 27, 29, 30 POWER (5V) ? CHECK TROUBLE IN U811 U811 (3.3V)? CHECK TROUBLE IN U201 ? U201 - 12 -...
Page 13
3. NO CLOCK (CLOCK GENERATOR) NO DOT CLOCK CHECK TROUBLE IN X201 20MHz ? X201 4. TROUBLE IN DPM TROUBLE IN DPM CHECK CHECK PC R713, R715 PC IS NOT GOING (SYNC) ? INTO DPM OFF MODE CHECK U203 PIN 102 TROUBLE IN WAVEFORM X201...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 12. 16. DATE: 2002. 12. 16. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.
Page 23
NVRAM Serial Host I/F Paralle l Crystal Serial I/F ROM IF Reference GPIO Clock Host 8051-st yle Externa l Generati on Contro lle r Interface Micro- ROM I/F co ntro lle r RAMs Internal Brightness / Output Dual LVDS Image Zoom / Panel Data Contr ast /...