Sony DVP-F11 Service Manual page 65

(5-4) ARP to RAM Address Bus
Data write other address read discord check
Error 10: ARP RAM address bus error
Caution: Address and data display in case of an error is
different from the display of other diagnosis (de-
scribed later).
Before starting the test, all addresses of RAM (IC304) are
cleared to 0x0000.
First, 0xA55A is written to the address 0x00000, and the
address data are read and checked from addresses 0x00001
to 0x80000 while shifting 1 bit each. Next, the data at that
address is cleared, and it is written to the address 0x00001,
and read and checked in the same manner. This check is
repeated up to the address 0x80000 while shifting the ad-
dress data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were al-
ready cleared to 0. In this check, the error display pattern is
different from that of other diagnosis; read data, written
address, and read address are displayed in this order. How-
ever, the message uses same template, and accordingly ex-
change Address and Data when reading. The following dis-
play, for example,
### Syscon Diagnosis ###
5-4. ARP to RAM Address Bus
Error 10: ARP - RAM Address B
Address : 0000A55A
Write Data : 00000000
Read Data : 00080000
Press NEXT Key to Continue
Press PREV Key to Repeat
_
shows the data 0xA55A was read from address 0x00080000
though it was written to the address 0x00000000. This im-
plies that these addresses are in the form of shadow. Also,
if the read data is not 0xA55A, another error will be present.
(5-5) ARP RAM Check
Data write read, and accord check
Error 11: ARP RAM read data discord
The program code data stored in ROM are copied to all
areas of RAM (IC304) connected to the ARP (IC303)
through the bus, then they are read and checked if they ac-
cord. If the detail check was selected initially, the data are
written to all areas and read, then the same test is conducted
once again with the data where all bits are inverted between
1 and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 11,
and the test is suspended.
6. AV Decoder
(6-2) 1930 RAM
Data write read, and accord check
Error 13: AVD RAM read data discord
The program code data stored in ROM (IC205 or IC206)
are copied to all areas of RAM (IC402, IC403) connected
to the AVD (IC401) through the bus, then they are read and
checked if they accord. Further, the same test is conducted
once again with the data where all bits are inverted between
1 and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 13,
and the test is suspended.
(6-3) 1930 SP
ROM AVD RAM
Error: Not detected.
The data including sub picture streams in ROM (IC205 or
IC206) are transferred to the RAM (IC402, IC403) in AVD
(IC401), and output as video signals from the AVD (IC401).
They are output from all video terminals (Composite, Y/C)
except EURO AV terminal.
7. Video
(7-2) Color Bar
AVD color bar command write
Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/C)
except EURO AV terminal.
8. Audio
(8-2) ARP 1930
Error 14: ARP
15 : ARP
(8-3) Test Tone
A pink noise signal is output from the AVD (IC401) through
optical coaxial digital terminal and analog audio terminal.
Error: Not detected.
All channels
Front Right Rear Left
Woofer are checked in this order.
Caution: Sub Woofer is checked only for low-frequency
components, and no sound will be heard unless a
proper super woofer is connected.
6-3
Video OUT
Video OUT
1930 video NG
1930 audio NG
2ch Left 2ch Right Front Left
Rear Right Center Sub