KX-F206TW 1 INTRODUCTION 1.1. INSULATION RESISTANCE TEST Change from original page 3 (1.2. INSULATION RESISTANCE TEST) 1. Unplug the power cord and short the two prongs of the plug with a jumper wire. 2. Turn on the power switch. 3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part (screw heads, control shafts, bottom frame, etc.).
KX-F206TW 1.2. SPECIFICATIONS Change from original page 7 (1.8. SPECIFICATIONS) Applicable Lines: Public Switched Telephone Network Document Size: Max. 216 mm (8 1/2”) in width Max. 600 mm (23 5/8”) in length Effective Scanning Width: 208mm (8 3/16”) Recording Paper Size: 216 mm max.
KX-F206TW 1.3. LOCATION OF CONTROLS 1.3.1. CONTROL PANEL Change from original page 9 (1.11.2. CONTROL PANEL)
Page 5
KX-F206TW 1.4. CONNECTIONS Change from original page 10 (1.12. CONNECTIONS) NOTE When you operate this products, the power outlet should be near the product and easily accessible.
KX-F206TW 2 TROUBLESHOOTING GUIDE 2.1. Program Mode Table Change from original pages 52, 53 ([2. Program Mode Table] in 2.3.4.2.2. Remote Programming) Code Function Set Value Default Remote setting Set the date and time mm/dd/yy hh:mm AM/PM --------- Your logo...
Page 7
KX-F206TW Code Function Set Value Default Remote setting Original setting 1:NORMAL/2:LIGHT/3:DARKER NORMAL Transmit basic list 1: START --------- Transmit advanced list 1: START --------- Transmit journal report 1: START --------- Journal 3 1: START --------- Transmit service list 1: START --------- OK : Can set the value by the remote programming feature or print a list.
KX-F206TW 2.2. Power Supply Board Section Change from original pages 65~67 (2.3.4.5. Power Supply Board Section) 1. Key components for troubleshooting The following components have been known to break frequently: F101, D101-D104, C109, Q101, PC101, ZD203, R302. This comes from our experience with experimental tests. For example: power supply, lightning surge voltage test, withstanding voltage test, intentional short circuit test, etc.
Page 11
KX-F206TW 3. Broken parts repair details (D101, D102, D103, D104) Check for a short-circuit in terminal 4. If D101, D102, D103 and D104 are short-circuited, F101 will melt (open). In this case, replace all of the parts (D101, D102, D103, D104, F101).
KX-F206TW 2.3. USER MODE (The list below is an example of the SYSTEM SETUP LIST the unit prints out.) Change from original pages 75 (2.4.3. USER MODE (The list below is an example of the SYSTEM SETUP LIST the unit prints out.))
KX-F206TW 2.4. SERVICE FUNCTION TABLE Change from original pages 76~77 (2.4.4. SERVICE FUNCTION TABLE) Code Function Set Value Effective Range Default Remarks Setting the pause time 001~600 × 100 msec 001~600 05000 msec Selects the pause time in 100 msec steps.
Page 14
KX-F206TW Code Function Set Value Effective Range Default Remarks Receive speed select 1: 9600BPS 9600 BPS Adjusts the speed to start training during FAX 2: 7200BPS reception. 3: 4800BPS 4: 2400BPS Ringer off in TEL/FAX 1: ON 1, 2 Sets the ringer switch off when a call is...
KX-F206TW 2.5. SERVICE MODE SETTINGS (Example of a printed out list) Change from original page 78 (2.4.5. SERVICE MODE SETTINGS (Example of a printed out list))
Page 16
OPERATION PANEL POWER SUPPLY AC110V SELE CTOR +24V SENSOR KEY MATRIX DIGITAL BOARD ANALOG BOARD +24V +24V LINE 3.3V MOS SW SRAM 256k EXT. RESET CODEC BELL PRINTER OP PANEL CONTROL HOOK SW ASIC HOOK PAPER PAPER MODEM IMAGE PROCESSING MOTOR I/F SP MUTE SENSOR...
KX-F206TW 3.3. ITS (Integrated Telephone System) and MONITOR SECTION Addition to original page 132 (6.9. ITS (Integrated Telephone System) and MONITOR SECTION) 6.9.5. HANDSET ALC DETECTION 1. Function In some case, it is a standard requirement that the sound level of the handset should be low when the circuit current is large (small line loss) and high when the circuit current is small (large line loss).
Page 19
KX-F206TW 3.4. POWER SUPPLY BOARD SECTION Change from original pages 137, 138 (6.12. POWER SUPPLY BOARD SECTION)
Page 20
KX-F206TW Using a different winding ratio results in the voltage function given by the formula in figure (c). As you can see, it is possible to keep VO constant by changing the ratio of TON and TOFF in response to variations in input voltage.
KX-F206TW 5 PRINTED CIRCUIT BOARD 5.1. PRINTED CIRCUIT BOARD (SWITCHING POWER SUPPLY) Change from original page 148 (11 PRINTED CIRCUIT BOARD (SWITCHING POWER SUPPLY)) (COMPONENT VIEW) (BOTTOM VIEW) SRF912UC CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF MITSUMI ELEC. CO., LTD.
KX-F206TW 6 SCHEMATIC DIAGRAM (SWITCHING POWER SUPPLY) 6.1. SCHEMATIC DIAGRAM (SWITCHING POWER SUPPLY) Change from original page 149 (12 SCHEMATIC DIAGRAM (SWITCHING POWER SUPPLY)) 300V -0.8V Cycle=2.2 s T101 TRANS CN301 Cycle=2.2 s D201 D102 D101 C202 D103 D104 1000p...
Ref. Part No. Part Name & Description Remarks PARTS LIST) PFJE1007Z LEAD, OPERATION This replacement parts list is for KX-F206TW only. PFJE1006Z LEAD, OPERATION PFDE1096Z LEVER, DOCUMENT DETECTION Refer to the simplified manual (cover) for other areas. PFDE1100Z LEVER, READ DETECTION...
KX-F206TW Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks (CONNECTORS) (SWITCHES) CN31 PQJP2D98Z CONNECTOR,2PIN EVQ11Y05B SPECIAL SWITCH CN301 PQJP8G30Y CONNECTOR,8PIN EVQ11Y05B SPECIAL SWITCH EVQ11Y05B SPECIAL SWITCH EVQ11Y05B SPECIAL SWITCH (RESISTORS) EVQ11Y05B SPECIAL SWITCH...