Sony DCR-TRV6 Service Manual page 87

For Schematic Diagram
• Refer to page 4-16 for printed wiring board.
• Refer to page 4-113 for waveforms.
1 2 3
FP-219 FLEXIBLE BOARD
(TRV6/6E/11/11E MODEL)
CCD IMAGER
NO MARK:REC/PB MODE
A
-REF.NO.:30000 SERIES- R :REC MODE
P :PB MODE
XX MARK:NO MOUNT
R3001
0
B
C3004
R3.7/P0
XX
B Q3001
0
UN9213J-(K8).SO
SWITCH
L3000
100uH
C
1 2 3 4 5 6 7
1 3
2
6 5 4
D
C3003
14 13 12 11 10 9 8
C3002 22u
0.1u 16V
F B
TA
C3001 R3000
E C3000
10p CH 2200
10u
10V
TA
A
IC3000
7
CCD IMAGER
IC3000
ICX220BKC-13 : TRV6/11 MODEL
ICX221BKC-13 : TRV6E/11E MODEL
F
SIGNAL PATH
G
VIDEO SIGNAL
CHROMA Y Y/CHROMA
REC
PB
H
16
4 5 6 7
TRV6 MODEL :DCR-TRV6
TRV6E MODEL :DCR-TRV6E
TRV11 MODEL :DCR-TRV11
TRV11E MODEL:DCR-TRV11E
LENS BLOCK
LENS BLOCK is replaced as a block,
So that these PRINTED WIRING BOARD
and SCHEMATIC DIAGRAM are omitted.
4-13
8 9 10 11
CN3001
50P
1 V3 V2 2
3 V4 V1 4
5 VSHT V_DRAIN 6
7 HDR_GND -6.5V 8
H2
9 H2 HDR_GND 10
H1
11 H1 HDR_GND 12
RG
13 RG HDR_GND 14
15 CCD_GND CCD_GND 16
17 CCD_OUT CCD_GND 18
19 CCD_GND CCD_GND 20
21 12V CCD_GND 22
23 S_GND S_GND 24
25 ZM_XA ZM_XB 26
27 ZM_A ZM_B 28
29 GND NightShot_Vcc 30
31 FC_SENS_OUT THERMO_OUT 32
33 FC_SENS_Vcc GND 34
35 FC_XA FC_XB 36
37 FC_A FC_B 38
39 ZM_SENS_OUT GND 40
41 ZM_SENS_Vcc HALL(+) 42
43 BIAS(+) HALL(-) 44
45 BIAS(-) GND 46
47 GND DRIVE(-) 48
49 DRIVE(+) SLOW SHUT 50
TO VC-241 BOARD
CN701
(SEE PAGE 4-26)
Precautions Upon Replaching CCD imager
• The FP-219 flexible board mounted as a repair part is not equipped
with a CCD imager.
When replaching this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electrictiy from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strog light.
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
12
S3000
SUPER
NIGHT SHOT
GND
LND300
4-14
CCD IMAGER
FP-219