Page of 4
Download Bookmark Comment

Honeywell H46C Installation Instructions

Honeywell humidity controller installation instructions.
Hide thumbs
   
H46C Humidity Controller
INSTALLATION INSTRUCTIONS
APPLICATION
5. Pull the wires from the switch box through the
opening in the adapter plate and connect to the
H46 leadwires with the solderless connectors
The H46C Humidity Controller is used with portable and
provided. See Fig. 2 and 3 for typical hookup.
central unit dehumidifiers to maintain relative humidity.
6. Push the wires back into the switch box.
The H46 has an spst, snap-acting switch designed for
7. Place the H46 against the adapter plate, making
line voltage circuits and two leadwires for switch box
certain the tab at the bottom of the plate fits into the
mounting.
notch on the H46.
8. Fasten the H46 to the adapter plate by tightening
the captive screw.
INSTALLATION
9. Replace the cover and the setting knob.
When Installing this Product...
2 X 3 IN.
SWITCH BOX
ADAPTER PLATE
1. Read these instructions carefully. Failure to follow
SCREWS (2)
them could damage the product or cause a
H46 CAPTIVE
hazardous condition.
MOUNTING SCREW
2. Check the ratings in the instructions and on the
H46
product to make sure the product is suitable for
(COVER OFF)
your application.
3. Installer must be a trained, experienced service
technician.
4. After installation is complete, check out product
operation as provided in these instructions.
CAUTION
Electrical Shock Hazard.
Can cause electrical shock or equipment
damage.
Disconnect power supply before connecting
WALL SURFACE
wiring.
ADAPTER PLATE
Location
PLATE TAB
NYLON
M7907
H46 LEADWIRES (2)
ELEMENT
Select a location about 5 ft (1.5m) above the floor in an
area with good circulation at average temperature and
humidity for the area to be controlled. Avoid locations
Fig. 1. Mounting H46C on vertical switch box.
near hot or cold air ducts and discharged air from the
controlled equipment.
Wiring
Mounting
Disconnect power supply before connecting wiring to
avoid electrical shock or equipment damage. All wiring
1. Remove the setting knob.
must comply with local codes or equipment damage. All
2. To remove cover, pull cover forward from device.
wiring must comply with local codes and ordinances. Do
3. Install a 2 in. x 3 in. (51 mm x 76 mm) vertical
not exceed contact and coil ratings when wiring into
switch box at the selected location.
system. See Fig. 2.
4. Using the two screws provided, fasten the adapter
plate to the switch box, as shown.
® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc. •
• All Rights Reserved
95-5367-4

   Related Manuals for Honeywell H46C

   Summary of Contents for Honeywell H46C

  • Page 1

    APPLICATION The H46C Humidity Controller is used with portable and central unit dehumidifiers to maintain relative humidity. The H46 has an spst, snap-acting switch designed for line voltage circuits and two leadwires for switch box mounting. INSTALLATION When Installing this Product...

  • Page 2

    AS REQUIRED. HEATING DAMPER MOTOR, IF USED. CLOGGED FILTER SWITCH OR COOLING PANEL CONNECTION. Fig. 3. Typical parallel wiring hookup for H46C with T87F/Q539A combination 95-5367-4 Wiring in series prevents overcooling but the air conditioner runs only when both the thermostat and dehumidistat are calling.

  • Page 3

    PROVIDE OVERLOAD PROTECTION AND DISCONNECT MEANS AS REQUIRED. HEATING DAMPER MOTOR, IF USED. CLOGGED FILTER SWITCH OR COOLING PANEL CONNECTION. Fig. 4. Typical series wiring hookup of H46C with T87F/Q539A combination for dehumidification and mildew control. T87F/Q539A INTERNALSCHEMATIC T87F TEMPERATURE...

  • Page 4

    H46C HUMIDITY CONTROLLER Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 95-5367-4 G.H. Rev. 07-03 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.

This manual also for:

H46e1013 - humidistat includes a plug

Comments to this Manuals

Symbols: 0
Latest comments: