SkyLink Household Aler HA-100 User Manual

Household Alert
1. INTRODUCTION
®
The Household Alert is designed to monitor your garage door and movement
indoor or outdoor. The Garage Door Monitor sensor can be used to monitor the
status of your garage door and advises you if the door is open. By placing
the sensor on the door panel, you will be alerted when the door is open.
The Indoor / Outdoor Motion sensor can be used to detect visitors at the
front door, detects activity on the driveway, monitors activity inside your
house etc.
If these sensors are triggered, they will transmit wireless signal to the receiver
which will beep and flash.
In this package, you should find a Garage Door Monitor
Outdoor Motion Sensor, a Household Alert
lithium battery, double-sided foam tape, ball-head joint and mounting
accessories.
Garage Door
TM
Monitor Sensor
Clip
3V Lithium
battery
Adapter
Please follow the instructions below to set up these sensors and receiver.
2. SET UP CODE CONNECTORS AND ZONE CONNECTORS
1. CODE CONNECTORS
In order for the sensor to communicate with the receiver properly, the
sensor's code must match with the receiver's code.
TM
For Garage Door Monitor Sensor, code connectors 1 to 6 can be found
by opening the battery cover. Note: Before opening the battery cover, it is
necessary to remove the transparent protective cover. Keep it for future
use. User is required to set these code connectors randomly. Each position
of the code connector can be set to "+", "-' or "0" positions. Refer to the
diagrams to set the code connectors properly. If the connector is placed
on the top and middle posts, that column is set on " + ". If the connector is
placed on the middle and bottom posts, that column is set on " - ". If the
connector is removed completely, (not placed on any posts), it is set to " 0 ".
(see diagram for examples of how to set a column to the three different
positions).
' '
0
'+'
'-'
Remove transparent protective cover
For indoor/ outdoor motion sensor, code connector 1 to 6 can be found
by unscrewing and opening the battery cover (refer to the diagram below
for the code connectors location.) The code settings on both sensors
must be the same.
®
Model HA-100
TM
Sensor, an Indoor/
® Receiver, an adapter, 3V
®
Household Alert
Receiver
Indoor/Outdoor
Motion Sensor
Double-sided foam tape
Ball-head joint
4 pcs 3 x 18 screws
1 pc 2 x 5 screw
Clip
Note: A connector can be removed with
the clip, as shown.
Code Connectors on garage door sensor
2. SET UP CODE CONNECTORS AND ZONE CONNECTORS (CONT)
For the receiver, code connectors 1 to 6 can be found opening the back
cover. (refer to the diagram below for the code connectors location.) The
code settings on both sensors and the receiver must be the same.
Ensure both motion sensor and receiver are set with the same code. The
code connectors can be seen after removing the back cover. Refer to the
diagram below for the code connection location.
Put the back cover back onto the receiver.
Code Connectors on motion sensor
Note: If you experience interference from a nearby system, which could
accidentally trigger your system, please change the code settings on
the sensor and receiver. The code setting on the sensor and receiver
should still match after changing the code setting.
2. ZONE CONNECTORS
Each receiver can work with up
to 4 different sensors (to repre-
sent 4 different zones on the
receiver). There are 2 connec-
tors that determine the zone
number 1, 2, 3 or 4. These 2
connectors can be found by
opening the battery cover. Please
follow table 1 to set the zone.
A B
Zone 1 + +
Zone 2 + -
Zone 3 - +
Zone 4 - -
Table 1
"+" in the table means the connec tor for that position should be placed on
the posts.
"-" in the table means the connector for that position should be removed.
Note: The factory default setting of the garage door sensor is zone 1.
The motion sensor is set to zone 2 at the factory.
3. POWER UP THE GARAGE DOOR MONITOR
HOUSEHOLD ALERT ® RECEIVER
After setting up all the connectors, both
units are ready to be powered up.
Plug in the adapter to the receiver, the
green LED will start flashing indicating
the receiver unit is powered up but no
sensor is detected. Push the detection
rod to it's fully retracted position.
Remove the battery cover on the sensor
and insert the 3V lithium battery to the
sensor as shown in the diagram.
The LED on the sensor will flash 8 times
to indicate the unit is properly powered
and there is signal transmission to the
receiver. The green LED on the receiver
will stop flashing and stay on. Make sure
to put the transparent protective cover
back in place after setting up.
Code Connectors on receiver
TM
Garage Door Monitor Sensor
Zone
connectors
Indoor/Outdoor Motion Sensor
Zone connectors
TM
SENSOR AND
Plug in adapter to the receiver
+
"+" positive
side up
Insert 3V battery to the sensor