Poulan Pro PB30 Operator's Manual page 10

✓
CHECKLIST
Before you operate your new riding mower,
we wish to assure that you receive the best
performance and satisfaction from this Qual-
ity Product.
Please review the following checklist:
✓ All assembly instructions have been
com plet ed.
✓ No remaining loose parts in carton.
✓ Battery is properly connected.
✓ Seat is adjusted comfortably and tight-
ened securely.
✓ All tires are properly inflated. (For ship-
ping purposes, the tires were overinflated
at the factory).
✓ Be sure mower deck is properly leveled
side-to-side/front-to-rear for best cutting
results. (Tires must be properly inflated
for leveling).
✓ Check mower belt. Be sure it is routed
properly around pulleys and inside all belt
keepers.
✓ Check wiring. See that all connections
are still secure and wires are properly
clamped.
While learning how to use your riding mower,
pay extra attention to the following important
items:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular
unleaded gasoline.
✓ Become familiar with all controls, their
location and function. Operate them
before you start the engine.
✓ Be sure brake system is in safe operating
condition.
✓ Be sure Operator Presence System and
Reverse Operation System (ROS) are
working properly (See the Operation and
Maintenance sections in this manual).
10
RIDING MOWER
DRIVE
KEY PART
NO. NO. DESCRIPTION
1 532 44 20-79 WHEEL ASM (REAR)
2 532 12 17-48 WASHER, 16 GA.
3 812 00 00-01 E-CLIP
6 532 15 69-72 SPACER AXLE
7 874 78 04-28 HCS 1/4-20 X 1-3/4 GR 5 ZD
8 532 44 18-51 WELMENT SUPPORT AXLE RH
9 532 44 19-36 SUBASM FINAL DRIVE
10 817 00 05-12 SCREW 5/16 - 18 X 3/4
11 532 43 67-41 BRACKET.SUPPORT.RH
12 532 43 61-48 CASE CHAIN RH
13 532 43 72-80 BEARING BALL 6207-SRS
14 532 43 71-76 SPROCKET DRIVEN 37 TOOTH
15 532 44 25-51 TUBE INPUT HEX
16 532 43 61-53 CHAIN PRIMARY DRIVE
17 532 43 72-82 BEARING BALL 6204-3-2RS
18 532 43 61-49 CASE CHAIN LH
19 818 05 10-10 SCREW 10 - 24 X 5/8 PAN HEAD
TORX
20 532 12 49-31 WASHER THRUST .75 X 1.230
22 532 43 66-96 WELMENT SUPPORT AXLE LH
23 818 10 10-08 SCREW TORX #10 - 14 X 1/2
32 532 43 61-51 BLOCK TENSION CHAIN
33 532 43 61-50 SPRING ADJUSTER TENSION
34 877 10 10-40 PIN CLEVIS 5/16 X 2-1/2
36 532 43 57-22 SHAFT INPUT CLUTCH
37 532 43 61-52 SPROCKET SPLINED 14 TOOTH
39 532 43 04-70 BEARING BALL
40 532 43 69-39 ARM BRAKE
41 532 10 95-53 SWITCH INTLK CL MWR GRY
4 TERM
43 873 80 05-00 NUT LOCK HEX W/INSERT
5/16 - 18 UNC
44 532 43 66-52 COVER END HEX
45 532 43 61-54 SPRING DRIVE
47 532 43 69-49 BRACKET MOUNT CABLE
LRV B
48 817 54 10-16 SCREW.HEX.HEAD WASH.10-
24X1.00
51 532 43 67-39 BRACKET SUPPORT LH
53 873 90 06-00 LOCK NUT, FLANGED
54 532 43 57-26 BEARING BALL
55 532 43 77-77 COVER WHEEL CLUTCH
57 532 43 65-59 WHEEL FRICTION
59 532 44 10-97 PLATE.CLUTCH.DRIVE
60 532 43 77-87 PLATE PRESSURE DRIVE
62 532 43 77-86 PLATE CLUTCH BRAKE
63 532 43 77-85 PLATE PRESSURE BRAKE
65 532 43 57-23 PLATE PRESSURE MASTER
66 532 43 57-24 BEARING THRUST 20MM
67 532 43 57-25 PLATE THROWOUT
68 532 43 57-28 BEARING BALL LOOSE
69 532 43 57-27 COVER CLUTCH
MODEL NUMBER PB30 (96022001400)
PRODUCT NUMBER 960 22 00-14
KEY PART
NO. NO. DESCRIPTION
70 532 41 15-55 GRIP LEVER
71 532 43 68-65 TUBE SHIFT LRV
72 872 11 04-06 BOLT CARR.
73 873 68 04-00 NUT CROWNLOCK 1/4 - 20 UNC
75 532 43 67-00 BRACKET MOUNT SHIFT
76 532 18 35-00 HUB SHIFT
78 532 42 90-55 SPACER NYLON .866 X 1.25 X
.250
79 874 78 04-12 BOLT.FIN.HEX.1/4-20 UNC X .75
80 810 04 04-00 WASHER LOCK HVY HLCL
SPRING
81 819 09 12-10 WASHER 9/32 X 3/4 X 10 GA.
84 819 11 16-10 WASHER 11/32 X 1.00 X 10 GA.
85 532 43 69-14 SPRING FRICTION PACK
86 532 43 73-04 BUSHING PACK FRICTION FD2
87 532 43 69-48 WASHER PLASTIC
88 532 43 67-01 STUD PACK FRICTION
89 532 43 72-99 SPACER PACK FRICTION FD2
90 819 11 14-16 WASHER.11/32 X 7/8 X 16 GA.
91 532 43 69-24 SUBASM.LINK.SHIFT
94 532 43 69-18 WELDMENT.SHIFT.FD2
95 532 43 68-66 PLATE.SHIFT
96 532 43 77-67 DRUM CLUTCH MULTI DISC
97 532 43 69-25 SUBASM LINK SHIFT PRIMARY
98 532 15 03-60 NUT LOCK CENTER 1/4 - 28
FNTHD
101 817 06 06-24 SCREW.3/8-16X1-1/2. SMGML.
TAP/R
102 532 08 67-77 THREAD.CUTTER
103 532 10 44-45 SWITCH.SEAT.
104 532 43 77-81 HUB CENTER
105 532 43 61-42 SPRING WAVE C125-H5
106 532 19 43-21 SPACER RETAINER
107 532 12 47-88 RETAINER.SPRING.1".ZINC/
CAD
108 532 43 67-84 BUSHING.5/16IDX7/16ODX1/2
109 532 19 32-68 CAP .HUB.AXLE.1.50 X 1.00
110 532 42 84-61 BRACKET SHIFTER FLEX
111 532 12 35-83 KEY.SQUARE.2.0 X .1845/.1865
112 818 10 10-12 SCREW TORX #10-14 X .750
113 873 90 05-00 NUT LOCK FLANGE HEX
114 532 43 62-82 BEARING FLANGE
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
35