Using Bluetooth; Use Any Remote To Control Your Dht-S514; Pairing The Sound Bar And Subwoofer - Denon DHT-S514 Owner's Manual

Using Bluetooth®
DHT-S514 can stream music wirelessly, via Bluetooth, from any compatible Bluetooth device such as a mobile phone, tablet, or laptop computer.
Pairing Your Bluetooth Device
Before you can stream Bluetooth audio to DHT-S514, you must pair your device to DHT-S514.
To pair the device to the DHT-S514 for the first time:
1 Press-and-hold the Bluetooth key
2 Go to Bluetooth settings on your device. Make sure the device's Bluetooth feature is set to "on".
3 From the Bluetooth list on your device, select "DHT-S514".
4 Playback audio on the Bluetooth source; you should now hear audio from the DHT-S514. DHT-S514's Bluetooth key LED will remain on as
long as DHT-S514's Bluetooth input is selected and active.
DHT-S514 can pair multiple Bluetooth devices; however, only one can play at a time. First come, first served. One Bluetooth Source will need to be
disconnected before another paired device can play.

Use Any Remote to Control your DHT-S514

It's easy to "teach" DHT-S514 to respond to nearly any conventional IR (infrared) remote, so that you may continue to use your favorite television
or cable/satellite. You may prefer to teach DHT-S514 only selected commands, to avoid unintentional operations and subsequent confusion
among some household members. Some DHT-S514 owners teach only Volume Up/Down and Mute, relying on the DHT-S514's front panel, or
DHT-S514's own remote, for other functions.
Learning commands (using Volume up as an example):
1 Press-and-hold the front panel's Learn button for 3 seconds; its key LED will flash slowly.
2 Now press the front-panel Volume up key; the Volume up key LED will also commence flashing slowly, in sync with the Learn LED.
3 Within 60 seconds, aim the "source" remote (for example, the television handset) from approximately 0.5m directly toward DHT-S514's
front panel, and press its Volume up key 4 times in slow succession; both flashing DHT-S514 LEDs will now light steadily for 3 seconds,
indicating a successful "learn. "
Unlearning commands
1 Press-and-hold the front panel's Learn button for 3 seconds; its LED will flash slowly.
2 Press the button you want to clear; the button's LED will also flash slowly, in sync with the Learn LED.
3 Press the learn button within 60 seconds; both LEDs will flash rapidly for 3 seconds. The command has been unlearned.
Seven of the eight DHT-S514 front-panel buttons can be taught to respond to an external remote. Simply repeat this three-step process for as
many of the other DHT-S514 commands (each associated with a front-panel button) as you wish.
Note: Rapid blinking of the two LEDs indicates a failed "learn". Press any other front-panel or DHT-S514 remote key to reset learning, and start
again. See the Troubleshooting section (vpage 13) for tips to help you successfully teach DHT-S514 to recognize the signals from your remote
control.
Once you have programmed DHT-S514 to respond to your "everyday" remote controller, you may wish to put away the DHT-S514 remote for
safekeeping. If you do, we recommend that you remove the battery, and wrap it in a slip of paper, masking-tape, or similar to prevent accidental
discharge and put it and the DHT-S514 remote someplace safe.
Some remotes can learn by pressing the remote key several times (up to four times).

Pairing the sound bar and subwoofer

The subwoofer and sound bar are paired at the factory. However if the communication is interrupted, follow this procedure.
1 Press the Pair Button on the subwoofer until the Status LED flashes red rapidly.
2 The sound bar power is turned on.
Press the Pair Button on the back of the sound bar. The Status LED on the subwoofer will be solid green.
Status LED
Red LED: Subwoofer not paired to, or searching for sound bar.
Green LED: Subwoofer is paired to sound bar. Your system is ready.
(front panel or remote) for at least 3 seconds; the Bluetooth LED will begin to flash rapidly.
12