Advertisement
HAWF3195R_07EM1.qxd
10/15/07
2:49 PM
Page 2
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
PLEASE READ AND SAVE
should always be taken including the following:
THESE IMPORTANT SAFETY
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids. Plug
INSTALLATION INSTRUCTIONS
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
used by or near children.
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
5. Unplug from outlet when not in use, when moving
PARTS THAT COULD BE REQUIRED TO ASSEMBLE YOUR
fan from one location to another, before putting on
FAN.
or taking off parts and before cleaning.
This window fan has been designed to fit double-hung
6. Avoid contact with moving parts.
windows with minimum openings of 24 inches (60 cm)
7. Do not operate in the presence of explosive and/or
wide and 12 inches (30 cm) high.
flammable fumes.
NOTE: This fan is designed and recommended for use
8. To avoid fire hazard, NEVER place the cord under
with a screen in the window.
rugs or any parts near an open flame, cooking or
other heating appliance.
Window Fan Installation
9. Do not operate any appliance with a damaged cord
1. Align the Window Fan horizontally in the window
or plug after the appliance malfunctions, or has been
with the controls facing you and the Built-In Extender
dropped/damaged in any manner.
Panel to the right.
10. The use of attachments not recommended or sold by
2. Set the fan into your window opening (note that in
the appliance manufacturer may cause hazards.
most cases the window screen does not have to be
11. Do not use outdoors.
removed or left open).
12. Do not let the cord hang over the edge of a table,
3. If the fan does not fit snugly to the left and right of
counter or come in contact with hot surfaces or leave
the window casing, pull out the Built-In Extender
exposed to high traffic areas.
Panel until the fan sits safely in your window.
13. To disconnect, grip plug and pull from wall outlet.
4. If the fan still does not fit snugly attach the Slider
Never yank on cord.
Safe
Extender Panel located in the polyfoam
®
14. Always use on a dry, level surface.
packaging in the original box. Align the slot in the
15. Do not operate fan until fully assembled with all
Slider Safe
parts properly in place.
the left side of your Window Fan. Slide the Slider
16. This product is intended for household use ONLY and
Safe
®
Extender Panel completely down the tab until
not for commercial or industrial applications.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
it is flush on both the top and bottom of the Window
Fan.
5. To keep the fan in place, carefully close the window
so that the bottom edge of the window rests on the
INSTRUCTIONS
flat area on the top of the fan.
For Slider Windows
1. Set the Fan Vertically in your window opening with
the left side of the fan situated on the bottom and
the Built-In-Extender panel on top.
2. Set the fan into your window opening (note that in
most cases the window screen does not have to be
removed or left open).
3. If the fan does not fit snugly to the top and bottom
of the window casing, attach the Slider Safe
Extender Panel and adjust the built-in extender
screen until the fan fits securely in your window.
WARNING: BE SURE FAN IS SECURELY INSTALLED IN
YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON
THE FAN WHILE IT IS IN THE WINDOW.
REMOTE CONTROL
Your remote control requires (2) AAA batteries for
operation. To install the batteries, simply depress the back
of the remote with your thumb on the indentations.
Insert batteries according to the diagram shown inside
and replace cover.
• Do not mix old and new batteries.
Figure 1
A. Front Grill
®
Extender Panel along the tab located on
B. Left Fan Directional Switch
C. Control Panel
D. Mode Button
E. LED Display
F. Temp Up (+)
G. Temp Down (-)
H. Right Fan Directional Switch
I. Extender Locks
J. Extender Panel (not shown)
K. Built-In Extender Panel
L. Remote Control (not shown)
F E AT U R E S - O P E R AT I O N S
• Do not mix alkaline, standard (carbon-zine), or
rechargeable (nickel-cadmium) batteries.
The remote controls the Mode, Speed, Temperature, and
Timer settings.
OPERATING INSTRUCTIONS
1. Plug cord into any standard 120 volt AC outlet.
2. To turn the fan on and control the speed, press the
mode button. Note that pressing the mode button will
allow you to cycle through the speed setting (High =
3, Med = 2, Low = 1) as well as the Automatic
Thermostat Temperature settings (Auto High = A3,
Auto Medium = A2, Auto Low = A1). 0 indicates the
®
Off position.
3. Set the airflow direction by sliding the fan directional
switches located above each fan blade. Note that the
fan blades work independently from one another and
can be used for air intake (bring fresh air in from
outside), exhaust (push air out from within the room)
or exchange (cycles air in and out of the room
simultaneously).
Auto Mode
Your fan is equipped with the AccuTemp Plus
Thermostat that will automatically turn the fan ON and
OFF depending upon the preset comfort temperature. This
is ideal for nighttime operation when temperatures can
drop below comfort levels.
C
D
E
F
G
H
A
B
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
For example, if you have set your thermostat to 75
degree and the room temperature drops to 74 degrees or
lower then the fan will automatically turn off. The fan will
then turn on again when the room temperature exceeds
75 degrees.
Setting Auto Mode
1. Press the Mode button to scroll to the desired auto
speed setting (A3, A2, or A1).
2. Choose the desired temperature setting by pressing
the Temp Up (+) or Temp Down (-) buttons. You may
select a temperature between 60 and 80 degrees
Fahrenheit. Once the desired temperature is set, the
digital display will return to show the ambient room
temperature. View the set temperature by pressing
either the Temp Up (+) or Temp Down (-) buttons.
IMPORTANT: If the fan does not start in the Auto
mode, please be sure that the set temperature is below
the current room temperature. Lower the set temperature
if you would like for the fan to start or switch over to the
manual speed modes.
Setting the Timer
1. Hold both the Temp Up (+) and Temp Down (-)
TM
Digital
buttons down until the digital display flashes "00".
2. Press the (+) or (-) buttons to change time in 1 hour
increments. Note selection ranges from 1 to 16
hours. When in the timer mode, the time remaining
will be displayed.
NOTE:
• The Timer Light will glow indicating the timer function
I
K
is active.
• If Timer is set when fan is ON, the time displayed will
turn the fan OFF once elapsed. If Timer is set when
fan is OFF, the time displayed will turn the fan ON.
(The default ON speed setting is Manual Low)
• Timer function can be turned off by pressing the
MODE key at any time.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan. Please remember:
• Always unplug the fan before cleaning.
• Do not allow water to drip on or enter into fan
housing.
• Be sure to use a soft cloth moistened with a mild
soap solution.
• Do not use gasoline, thinner or benzene as a cleaner.
Fan Cleaning
Clean the fan grills, extender screen, and extender panels
with a soft, damp cloth. Please use caution around the
motor housing area. Do not allow the motor or other
electrical components to be exposed to water. Also, using
a soft bristle brush attachment, a vacuum cleaner may be
used to extract dust buildup on the grill areas. Note to
turn the fan off before cleaning.
FAN STORAGE
When storing your fan in the off season, it is important to
keep it in a safe dry location. It is important to protect
the fan head from dust. We strongly recommend using
the original box from purchase.
WINDOW FAN ACCESSORIES
To order please go to
Window Fan
www.holmesproducts.com
Extender Panel
or call 1-800-546-5637
If you have any questions regarding your product or
would like to learn more about other Holmes
®
products, please contact our Consumer Service
Department at 1-800-546-5637 or visit our website at
www.holmesproducts.com
Advertisement
