1. Manuals
  2. Brands
  3. Crestron Manuals
  4. Touch Panel
  5. TPMC-8L
  6. Quick manual

Crestron TPMC-8L Quick Manual

Hide thumbs Also See for TPMC-8L:
Table of Contents

Advertisement

Quick Links

See also: Operation & Installation Manual

Advertisement

Table of Contents
loading

Related Manuals for Crestron TPMC-8L

Summary of Contents for Crestron TPMC-8L

  • Page 2 Crestron Quick Guide to Touchpanel Connections Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ® ® Windows and Windows XP are registered trademarks of Microsoft Corporation in the United States and other countries.

  • Page 3: Table Of Contents

    Crestron Quick Guide to Touchpanel Connections Contents   INTRODUCTION.............................. 1   TPMC‐8L ................................ 2   TPMC‐8X  ................................ 4   TPMC‐8X‐DSW .............................. 5   TPMC‐8T ................................ 7   TPMC‐12, TPS‐15, AND TPS‐17  .......................... 9   TPS‐12G‐QM AND TPS‐15G‐QM  .........................  1 4   TPMC‐CH‐IMC TOUCHPANEL INTERFACE ......................  1 8   TPS‐3000 AND TPS‐4000  ............................  2 2  ...

  • Page 5: Introduction

    Crestron Quick Guide to Touchpanel Connections Introduction This document contains detailed hookup information for the current line of Crestron touchpanels. Additional information may be found in the specific operations manual for each product, refer to the Crestron website (www.crestron.com). CAUTION: Do not apply excessive pressure to the touchscreen display during handling.

  • Page 6: Tpmc-8L

    Crestron Quick Guide to Touchpanel Connections TPMC-8L Power One 2.5 mm barrel DC power jack; 12 Volt DC power input (power 12V 3.5A supply not included). One 2-pin 3.5 mm detachable terminal block 24 VDC 24 Volt DC power input; Wire size: 18 AWG maximum...
  • Page 7 Crestron Quick Guide to Touchpanel Connections USB is a connectivity specification developed by the USB Implementers Forum that provides a single, simple, standardized way to connect up to 127 devices to a computer. USB shielded cables contain two wires for power +5 volts (red) and ground (brown) and a twisted pair of wires (yellow and blue) that carry data.

  • Page 8: Tpmc-8X

    The TPMC-8X should be used in a well-ventilated area. To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications. When making connections to the TPMC-8X, consider the following: Use the included Crestron power supply for these devices. The power supply cable cannot be extended.

  • Page 9: Tpmc-8X-Dsw

    Crestron Quick Guide to Touchpanel Connections TPMC-8X-DSW POWER One 2-pin 3.5 mm detachable terminal block 24 VDC 24 Volt DC power input Wire size: 18 AWG maximum NOTE: If the TPMC-8X-DSW is to be fed power from a Cresnet bus (the 24 and G lines), be sure that the Cresnet data lines (Y and Z) are not connected to the TPMC-8X-DSW, nor shorted together, to ground or to any metal surface.
  • Page 10 Crestron Quick Guide to Touchpanel Connections USB is a connectivity specification developed by the USB Implementers Forum that provides a single, simple, standardized way to connect up to 127 devices to a computer. USB shielded cables contain two wires for power +5 volts (red) and ground (brown) and a twisted pair of wires (yellow and blue) that carry data.

  • Page 11: Tpmc-8T

    Crestron Quick Guide to Touchpanel Connections TPMC-8T * Crestron recommends using either the power jack on the base or on the side of the panel but not both at the same time. POWER 12V 3.5A Power jack (Power pack included) CAUTION: Use only Crestron power supplies for Crestron equipment.
  • Page 12 Crestron Quick Guide to Touchpanel Connections One 8-wire RJ-45 with 2 LED indicators 10/100BaseT Ethernet port Green LED indicates link status Yellow LED indicates Ethernet activity. SIGNAL SIGNAL TX + TX - RC - USB is a connectivity specification developed by the USB Implementers Forum that provides a single, simple, standardized way to connect up to 127 devices to a computer.

  • Page 13: Tpmc-12, Tps-15, And Tps-17

    Crestron Quick Guide to Touchpanel Connections TPMC-12, TPS-15, and TPS-17 TPS-15 and TPS-17 TPMC-12 Doc. 4903B...
  • Page 14 Crestron Quick Guide to Touchpanel Connections RS-232 This 6-pin RJ-11 connector mates with a 9-pin serial port of a PC. The connecting cable is not supplied. Use this port to establish a direct connection between the touchpanel and a PC without a control system or network connection.
  • Page 15 The flash memory slot is accessible on the rear panel of the unit. QM IN (QuickMedia Input) The eight-pin RJ-45 QuickMedia transport port accepts Crestron Certified Wiring carrying audio, video, and microphone signals. The QM input port conforms to the 568B wiring standard. Refer to the following table for connector pinouts.
  • Page 16 IMC interface module. This port provides component, composite or S-video balanced input to the touchpanel over Crestron Certified Wiring. Description of the pinouts is shown in the following table. A cable for this connection is provided with the touchpanel. CAUTION: Only use the TPMC-CH-IMC Interface Module when connecting this port.
  • Page 17 This 8-pin RJ-45 connector provides connectivity to the CNX-BIPAD or with the TPMC-CH-IMC interface module. This port uses Crestron Certified Wiring and provides audio input to the touchpanel and microphone output from the touchpanel. A description of the pinouts is shown in the following table.

  • Page 18: Tps-12G-Qm And Tps-15G

    Crestron Quick Guide to Touchpanel Connections TPS-12G-QM and TPS-15G-QM RS-232 This 6-pin RJ-11 connector mates with a 9-pin serial port of a PC. The connecting cable is not supplied. Use this port to establish a direct connection between the touchpanel and a PC without a control system or network connection.
  • Page 19 Crestron Quick Guide to Touchpanel Connections One 8-wire RJ-45 connector with two LED indicators: The green LED indicates network speed The yellow LED indicates Ethernet activity This connector provides an Ethernet 10baseT/100baseTX, full duplex, IEEE 802.3U compliant network connection. SIGNAL...
  • Page 20 Crestron Quick Guide to Touchpanel Connections QM IN 1 and 2 (QuickMedia Inputs) Two 8-wire RJ-45 female, QuickMedia input ports; Signal types: Dynamically configurable under system control as: • One RGB (VGA) input with stereo program audio and two mic channels or •...
  • Page 21 (1) 2.1 mm barrel DC power jack, 24 Volt DC power input; Passes through to NET port to power Cresnet devices. CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. USB Ports Two USB Type A female, USB 1.1 ports for mouse or other external pointing device...

  • Page 22: Tpmc-Ch-Imc Touchpanel Interface

    Crestron Quick Guide to Touchpanel Connections TPMC-CH-IMC Touchpanel Interface This 4-position mini-terminal block connector is used to connect to other Cresnet peripherals in a system. Another NET connector is located on the other side of the module. Data and power for the TPMC-CH-IMC are provided via either connection.
  • Page 23 Crestron Quick Guide to Touchpanel Connections VIDEO The video input consists of three BNC connectors for unbalanced video signals. The component, composite or S-video input signal from an external video source is connected to these ports. AUDIO IN AUDIO IN Pinouts...
  • Page 24 Crestron Quick Guide to Touchpanel Connections AUDIO OUT AUDIO OUT Pinouts The 5-position mini-terminal block DESCRIPTION connector mates with the included connector and provides balanced Left Positive and/or unbalanced microphone Left Negative output. Ground Right Positive Right Negative Unbalanced Balanced...
  • Page 25 Crestron Quick Guide to Touchpanel Connections AUDIO (To Panel) This 8-pin RJ-45 connector mates with the TPMC-15-CH or TPMC-17-CH touchpanel. This port uses CAT5 wiring and provides audio input to the touchpanel and microphone output from the touchpanel. Audio In/Out...

  • Page 26: Tps-3000 And Tps-4000

    Crestron Quick Guide to Touchpanel Connections TPS-3000 and TPS-4000 NOTE: TPS-3000 and TPS-4000 include a TPS-IMPC Interface Module for system connection. Refer to page 24 for hookup details. NOTE: The audio connectors are color-coded blue. Hardware connections for the TPS-3000 and TPS-4000 (Back of the base is shown)
  • Page 27 The 10-pin RJ-45 connector cable supplied by Crestron is a custom cable and is the only one that should be used. The end of the cable has a metal shield that is required to protect the equipment. Using non-Crestron cables will result in damage to the product.

  • Page 28: Tps-Impc Touchpanel Interface

    Crestron Quick Guide to Touchpanel Connections TPS-IMPC Touchpanel Interface The TPS-IMPC is designed specifically to serve as an interface module for the Crestron tilt touchpanel. It is ® supplied with every Isys -tilt touchpanel that includes audio capability. A network connector and video input connectors are located on one side of the unit.
  • Page 29 When power is supplied to the TPS-IMPC through this connector, a Cresnet power connection on the NET connector is not required to display video on the touchpanel. CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. CAUTION: If power is provided to the TPS-IMPC from the +24VDC on a Cresnet connector or the PW-2420RU, power must not be applied to the power input on the touchpanel base.
  • Page 30 The 10-pin RJ-45 net/video connector cable supplied by Crestron is a custom cable and is the only one that should be used. The end of the cable has a metal shield that is required to protect the equipment. Using non-Crestron cables will result in damage to the product.
  • Page 31 Crestron Quick Guide to Touchpanel Connections AUDIO (To Panel) This 8-pin RJ-45 mates with the TPS-3000, TPS-5000, or TPS-6000 touchpanel. The 8-pin audio cable assembly is supplied. Even though the 10-pin net/video cable may fit into the port, do not use it. This port provides audio input to the touchpanel and microphone output from the touchpanel.
  • Page 32 Crestron Quick Guide to Touchpanel Connections MIC OUT The port mates with a three-pin connector (supplied) and produces line level differential output. MIC OUT Pinouts DESCRIPTION Positive Negative Shield Doc. 4903B...

  • Page 33: Tps-4L

    Crestron Quick Guide to Touchpanel Connections TPS-4L LAN (Ethernet) One 8-wire RJ-45 connector with two LED indicators (green LED indicates network speed, yellow LED indicates Ethernet activity). This connector provides an Ethernet 10baseT/100baseTX, full duplex, IEEE 802.3U compliant network connection.

  • Page 34: Tps-6L

    Crestron Quick Guide to Touchpanel Connections TPS-6L LAN (Ethernet) One 8-wire RJ-45 connector with two LED indicators (green LED indicates network speed, yellow LED indicates Ethernet activity). This connector provides an Ethernet 10baseT/100baseTX, full duplex, IEEE 802.3U compliant network connection.
  • Page 35 (requires SPK-6L); Input Impedance: 10k ohms balanced, 5k ohms unbalanced; Maximum Input Level: 2 V balanced/unbalanced; Normally connects to a Crestron CAT5 balanced audio source via CresCAT cable; Maximum CAT5 Cable Length: 1000 feet. PIN #...
  • Page 36 Input Impedance: 100 ohms balanced, 75 ohms unbalanced Input Level: 1 V nominal Balanced input normally connects to a Crestron CAT5 balanced video source via CresCAT cable, using +, -, and S connections. Unbalanced video uses S (shield) and C connections.

  • Page 37: Tps-6X-Ds And Tps 6X-Dsw

    Crestron Quick Guide to Touchpanel Connections TPS-6X-DS and TPS 6X-DSW TPS-6X-DS TYPE Color SIGNAL Gray Ground Orange/White Ethernet TX+ Orange Ethernet TX- Green/White Ethernet RX+ Interface Module Connector Blue Cresnet Y (to TPS-6X-IMCW) Blue/White Cresnet Z 10-Position RJ-50 Green Ethernet RX-...
  • Page 38 1.5 V maximum Maximum DC offset: ±2 Volts ® Connects to any Crestron CH CAT5 Video Out port via CresCAT cable (S=shield) LAN (Ethernet) One 8-wire RJ-45 connector provides an Ethernet 10baseT/100baseTX, full duplex, IEEE 802.3U compliant network connection.

  • Page 39: Tps-6X-Imcw

    Input level: 1 V nominal, 1.5 V maximum Maximum DC offset: ±2 Volts ® Connects to any Crestron CH CAT5 Video Out port via CresCAT cable (S=shield) Power One on front panel and one on back panel. 2.5 mm barrel DC power jack, 12 Volt DC power input;...

  • Page 40: V-Panels

    Crestron Quick Guide to Touchpanel Connections V-Panels Available as 12" and widescreen 15" displays in black or white. V-Panel displays are ultra-thin and may be installed flush mount, on a standard VESA mount or a desktop tiltcase. The new sleek design is accomplished by separating the Digital Graphics Engine (DGE), which is rack mounted up to 200 feet away.

  • Page 41: Digital Graphics Engines Dge-1 And Dge-2

    Crestron Quick Guide to Touchpanel Connections Digital Graphics Engines DGE-1 and DGE-2 DGE-1 D and M Ports WIRE COLOR Orange/White Orange Green/White Blue Blue/White Green Brown/White Brown 24 A B G Port SIGNAL DESCRIPTION WIRE COLOR +24 VDC DC Power...
  • Page 42 Crestron Quick Guide to Touchpanel Connections LAN (Ethernet) One 8-wire RJ-45 connector provides an Ethernet 10baseT/100baseTX, full duplex, IEEE 802.3U compliant network connection. SIGNALS SIGNALS TX + TX - RC - RC + Audio I/O WIRE COLORS AUDIO I/O WIRE COLORS...
  • Page 43 Crestron Quick Guide to Touchpanel Connections Basic V-Panel Hookup Example Doc. 4903B...

  • Page 44: Tpmc-4Sm

    Input voltage range: 0-30 Volts DC Sensing threshold: ≥ 4.5 Volts DC active, ≤ 1 Volt DC inactive Maximum DC load: 4 Watts @ 24 Volts DC, provides operating power for up to (4) Crestron GLS Series occupancy sensors Doc. 4903B...

  • Page 45: Cresnet Touchpanel Power Q

    Cresnet power then their predecessors. (For instance, the TPS-15G-QM draws 75 watts of Cresnet power.) Considering power loss (due to resistance) in cable, and the 75 Watt maximum output of Crestron power supplies, it appears that the maximum distance between a power supply and a newer touchpanels will be much less than previous.
  • Page 46 Crestron Quick Guide to Touchpanel Connections Maximum Cable Lengths for TPS panels using 75 watts of Cresnet Power Cresnet 16 awg CAT5 12 awg (18 awg R=6) (R=4) (2-cond R=13) (R=1.6) 155’ 232’ 71’ 580’ TPS-12 (L) 102’ 153’ 47’...

  • Page 47: Example Hookup And Application Diagrams

    Crestron Quick Guide to Touchpanel Connections Example Hookup and Application Diagrams TPS-12G-QM and TPS-15G-QM Interface: QuickMedia Device Doc. 4903B...
  • Page 48 Crestron Quick Guide to Touchpanel Connections TPS-12G-QM and TPS-15G-QM Interface: Extended Application Dual Video/RGB Windows and Audience Presentation Doc. 4903B...
  • Page 49 Crestron Quick Guide to Touchpanel Connections TPS-12G-QM and TPS-15G-QM Kitchen Control Application TPS-12G-QM or TPS-15G-QM Podium Application – with QM-MD7X2 Switcher for Multiple AV Inputs Doc. 4903B...
  • Page 50 Crestron Quick Guide to Touchpanel Connections TPMC-CH-IMC Interface Connections for TPS-12, TPS-15, and TPS-17 Doc. 4903B...
  • Page 51 Crestron Quick Guide to Touchpanel Connections QuickMedia Interface Connections for TPS-12, TPS-15, and TPS-17 Doc. 4903B...
  • Page 52 Crestron Quick Guide to Touchpanel Connections Balanced AV Distribution Connections for TPS-12, TPS-15, and TPS-17 (CNX-BIPAD8 and CNX-PVID8) Doc. 4903B...
  • Page 53 Crestron Quick Guide to Touchpanel Connections Balanced CAT5 AV Distribution Connections for TPS-12, TPS-15, and TPS-17 (C2N-IADS30X24 and C2N-IVDS24X24) Doc. 4903B...
  • Page 54 Crestron Quick Guide to Touchpanel Connections TPS-12, TPS-15, or TPS-17 Family Room Application – with Audio and Video Distribution Doc. 4903B...
  • Page 55 Crestron Quick Guide to Touchpanel Connections TPS-12, TPS-15, or TPS-17 Application – Podium Control with QM-MD4X2 Switcher for Dual AV Input Doc. 4903B...
  • Page 56 Crestron Quick Guide to Touchpanel Connections TPS-15 Application with CNX-BIPAD8 and CNX-PVID8X3 Doc. 4903B...
  • Page 57 Crestron Quick Guide to Touchpanel Connections TPS-17 Application – with Intercom, Audio Distribution, Video Distribution, Security, and Phone System Doc. 4903B...

  • Page 58: Appendix A: Quickmedia Installation Notes

    The total accumulated skew from QM transmitter to QM receiver must not exceed 15 ns (nanoseconds). Crestron recommends a cable with a rating of less than or equal to 15 ns over its entire length. For example, if using a cable with a rating of 15 ns/100 meters (100 meters = 328 feet), connecting the QM-...
  • Page 60 Crestron Electronics, Inc. Quick Guide to Touchpanel Connections 15 Volvo Drive Rockleigh, NJ 07647 Doc. 4903B Tel: 888.CRESTRON 12.09 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.

This manual is also suitable for:

Tpmc‐8xTpmc‐8x‐dswTpmc‐8tTpmc‐12Tps‐15Tps‐17 ... Show all

Table of Contents