Operating Instructions; Start Up/Shut Down/Restart - Mr. Heater MH50KT Operating Instructions And Owner's Manual

c. Slide a small washer, spacer, small washer onto the axle
next to the wheel.
d. Slide the partially assembled axle through the wheel
support frame.
e. Slide the small washer, spacer, and small washer onto the
axle next to the wheel support.
f. Slide the wheel then large washer onto the axle and hold
in place with the remaining cotter pin.
g. Install the caps over the larger washers to finish the wheel
assembly.
2. Position the heater on the wheel support frame assembly
with the exit opposite the wheels.
3. Use eight screws and nuts to attach the handles to the top
of the tank flange. The screws will go through the handles,
tank flange and wheel support frame. Install the nuts and
finger tight only until all nuts are installed.
4. Tighten all the nuts.
5. Attach cord caddies to handles using No. (4) & No. (5)
screws and nuts.
Handle assembly for 125KT, 175KT& 210KT only.
* Pkg Of Nuts & Bolts Included
ITEM PART NO. DESCRIPTION
1 24338 Handle, Front
2 24338 Handle,Rear
3 24339 Wheel Support Frame
4 26977 Machine Screw Blk (long)
5 26037 Kep Nut Blk
6 28746 Axle (125KT - 175KT)
28761 Axle (210KT only)
7 28752 Wheel (8'' Dia.)
22110 Wheel (13'' Dia. 210KT only)
8 28751 Cap
9 28748 Spacer (125KT - 175KT)
28762 Spacer (210KT only)
10 28749 Washer, Large
1 1 28750 Cotter Pin
12 28754 Ext. Cord Caddy
13 27336 Machine Screw Blk (Small)
Enerco Group, Inc. | Kerosene Forced Air Heater
PREPARING FOR OPERATION
1. Check the heater for possible shipping damage. If any is
found, immediately contact the manufacturer at
800-251-0001.
2. Follow all of the "Precautions".
3. Fill the fuel tank with clean kerosene, JP8 Jet Fuel, #1/#2
Diesel or #1/#2 Fuel Oil. In extremely cold weather,
condensation may develop in the tank and it is recommended
that a tablespoon of de-icer be added for each gallon (4
liters) of fuel in the tank. When filling the heater, use at least
2 gallons (8 liters) of fuel. Be sure heater is level and do not
overfill. Use a funnel or can with a long fill spout.
IMPORTANT: Before filling fuel tank the first time or after
extended storage periods, drain the fuel tank of any
moisture or condensation.
4. Locate heater at a safe distance from combustible
materials. Models 50K & 75KT are not suitable for use on
wood floors or other combustible materials. When used, the
heater should rest on suitable insulating material at least 1
inch thick and extending 3 ft. or more beyond the heater in
all directions.
HEATER START UP
1. 50K: Plug the heater into a grounded 115V, 60 Hz, 1 Ø
outlet.
75KT, 125KT, 175KT & 210KT: Turn thermostat to lowest
setting, make sure "On/Off" switch is "Off". Plug the
heater into a grounded 115V, 60 Hz, 1 Ø outlet.
Turn thermostat to highest setting. Start heater by
pushing toggle switch to "On" position (light signifies switch
is in "ON" position). Adjust thermostat to desired setting.
Heater will cycle on/off as heat is required.
For all models:
• In cold weather (below 10° F), starting may be
improved by holding a finger over the vent hole of
the pump adjustment screw cap until the heater
starts.
• This unit is equipped with an interrupt circuit. The
reset is located near the power cord. If the unit does
not start, press the reset button.
HEATER SHUT DOWN
50K: Unplug heater from power source.
1.
75KT, 125KT, 175KT & 210KT: Push "On/Off" switch
QTY
to "Off" position. For extended shutdown, unplug
heater from power source.
1
1
RESTART AFTER DIAGNOSTIC SAFETY SHUTDOWN
1
(50K, 75KT, 125KT, 175KT & 210KT) See page 7
8
12
Wait 5 minutes.
1
1.
1 2. Press reset button.
2
2
2
2
2
2
2
2
4
5
Operating Instructions and Owner's Manual 04/07 70276 Rev.C