Related Manuals for Black & Decker 6121
Summary of Contents for Black & Decker 6121
- Page 1 384282/6121/JUN97 5/2/02 2:00 PM Page 2 Black & Decker (U.S.) Inc. • 701 East Joppa Road, Towson, Maryland 21286 Printed in U.S.A. (MAR95-CD-1) Form No. 154428 Copyright © 1995 JUN97-CD-1 1997 384282...
- Page 2 384282/6121/JUN97 5/2/02 2:00 PM Page 3 Instruction Manual 6121 Right Angle Random Orbit Sander/Polisher...
-
Page 3: Important Safety Instructions
384282/6121/JUN97 5/2/02 2:00 PM Page 4 Getting the most out of your tool. FOR YOUR SAFETY - ALL TOOLS Please take time to read this manual and pay particular attention to the safety rules we’ve provided for your protection. If you have any questions about... -
Page 4: Safety Instructions For All Tools
384282/6121/JUN97 5/2/02 2:00 PM Page 1 Safety Instructions For All Tools • EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current • KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. -
Page 5: Additional Safety Instructions
384282/6121/JUN97 5/2/02 2:00 PM Page 2 ADDITIONAL SAFETY INSTRUCTIONS Switch (See Figure 2) To turn the unit on, slide the switch forward (the symbol “I” • Always wear eye protection and a respirator when sanding. will be visible.) To turn the unit off, slide the switch back (the symbol “O” will •... -
Page 6: Dust Collection
384282/6121/JUN97 5/2/02 2:00 PM Page 3 Dust Collection Your sander/polisher comes equipped with a cloth filter bag to collect the dust generated during sanding. To empty the dust bag, first turn off and unplug tool. Firmly pull the bag off while holding the rubber boot (Figure 3). -
Page 7: Application Notes
384282/6121/JUN97 5/2/02 2:00 PM Page 4 best finish possible, start with coarse grit sandpaper and change gradually and clean up BEFORE eating, drinking or smoking. Articles of food, drink, to finer and finer paper. Vacuum and wipe surface with a tack cloth or smoking should not be left in the work area where dust would settle on between grit steps. - Page 8 384282/6121/JUN97 5/2/02 2:00 PM Page 5 its bright orange color. Even though it is not the hardest, the way the abra- holes (120 x 120). The higher the number the finer the particle size. Common sive fractures gives you a good cutting edge for woodworking.
- Page 9 384282/6121/JUN97 5/2/02 2:00 PM Page 6 ously sand the dent, you may create a cupped surface. Spread a light coat of a good grade of polish, with a soft clean cloth or brush, over a small area and apply the sander/polisher before the polish dries.
- Page 10 384282/6121/JUN97 5/2/02 2:00 PM Page 7 Since everyone does not use the same type of Power Polish, we recom- CAUTION: The use of any non-recommended accessory may be hazardous. mend you clean and polish a test section on a flat area of the car FIRST.
- Page 11 384282/6121/JUN97 5/2/02 2:00 PM Page 8 icals or solvents to clean the tool. These chemicals could seriously damage Every B&D tool is of the highest quality. the engineering polymers used to construct your sander. If you typically If you wish to contact us regarding this product, please call toll wrap the cord around the tool when you store it, leave a generous loop of cord such that the strain relief does not bend.
- Page 12 384282/6121/JUN97 5/2/02 2:00 PM Page 9 YOUR POWER TOOLS MAY BE SERVICED AT THE FOLLOWING B&D SERVICE CENTERS. ALABAMA: IOWA: OHIO (CONT’D) Birmingham 35209, 2412 Green Springs Hwy....205-942-0538 Des Moines 50310, 3427 Merle Hay Rd.
- Page 13 384282/6121/JUN97 5/2/02 2:00 PM Page 10 ALBERTA Edmonton T6E 6H6, 3845 99th St... 403-462-5005 BRITISH COLUMBIA Vancouver V5M 3Y7, 1735 Boundary Rd..604-291-9942 MANITOBA Winnipeg R3H OK3, 934 St. James St..204-783-7294 NOVA SCOTIA Halifax B3K 2A4, 6100 Young Street.