Page 1
Your variable speed belt sander has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product.
n Introduction ... 2 n General Safety Rules ... 3-4 n Specific Safety Rules... 4 n Symbols... 5-6 n Electrical ... 7 n Features... 8-9 n Assembly ... 9 n Operation... 10-15 n Maintenance ... 16-17 n Parts Ordering / Service ... 18 This tool has many features for making its use more pleasant and enjoyable.
WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA n Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. n Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
SERVICE n Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. n Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME Volts Amperes Hertz Watt Minutes Alternating Current Direct Current...
Page 6
The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL DANGER: WARNING: CAUTION: CAUTION: SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair.
DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three- wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.
PRODUCT SPECIFICATIONS Belt Size ...3 in. x 21 in. Sanding Surface... 16.5 sq. in. No Load Speed ...775 - 1,150/min. TRACKING REAR HANDLE DRIVE ROLLER BELT TENSION RELEASE LEVER FEATURES Input ...120 V, 60 Hz, AC only, 6.0 Amps Net Weight... 8.8 lbs. KNOB FRONT ROLLER...
Before attempting to use this product, familiarize yourself with all operating features and safety rules. SWITCH TRIGGER To turn the sander ON, depress the switch trigger. Release switch trigger to turn your sander OFF. LOCK- ON BUTTON The lock-on feature allows you to lock the switch trigger in the ON position.
Finally, use finer grit for finishing the surface. Always continue sanding with each grit until the surface is uniform. SETTING THE BELT SANDER SPEED Refer to the chart below for belt sander speed selections. SPEED « « «...
WARNING: Do not let your fingers rest over the front or right edge of the sander. If the sanding belt were to run off, or if it were not properly adjusted, your fingers could come in contact with the moving sanding belt resulting in possible serious injury.
Page 12
Install sanding belt; make sure arrow inside of belt is pointing in the direction of rotation, which is clockwise when looking into open side of sander. NOTE: Match the arrow on the sanding belt to that of the belt tension housing.
Page 13
Using the rear handle to control the sander and the front handle only to guide it, move it slowly over the work. Allowing the sander to remain in one place will result in an uneven surface. WARNING: Keep a firm grip on sander with both hands at all times.
Page 14
When correctly adjusted, the outer edge of the belt will be even with the outer edge of the sander. Belt life will be greatly increased if a few seconds are spent adjusting the belt tracking.
Page 15
DUST BAG See Figure 10. The dust bag provides a dust collection system for the sander. It should be installed over the exhaust hole located on the side of the sander. For more efficient operation, empty dust bag when half full.
WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
Page 17
TIMING BELT REPLACEMENT See Figures 11 - 12. n Unplug the sander. WARNING: Failure to unplug the sander could result in accidental starting causing possible serious personal injury. n Remove dust bag. n Remove sanding belt from sander. Follow instructions on page 12 to remove sanding belt.
Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers.