Central Pneumatic 92841 Owner's Manual
  1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Paint Sprayer
  5. CENTRAL PNEUMATIC 92841
  6. Owner's manual

Central Pneumatic 92841 Owner's Manual

Low volume low pressure spray gun
Hide thumbs Also See for 92841:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic 92841

Summary of Contents for Central Pneumatic 92841

  • Page 2: Table Of Contents

    Distractions are able to result in fire, and injury to persons. the loss of control of the tool. Page 2 For technical questions, please call 1-800-444-3353. Item 92841...

  • Page 3: Personal Safety

    Use only lubricants supplied with the by qualified repair personnel. tool or specified by the manufacturer. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. Item 92841 For technical questions, please call 1-800-444-3353. Page 3...

  • Page 4: Air Source

    Risk of Respiratory Injury. Wear NIOSH-approved respirator. Cubic Feet per Minute flow SCFM at standard conditions WARNING marking concerning Risk of Explosion. National pipe thread, tapered National pipe thread, straight Page 4 For technical questions, please call 1-800-444-3353. Item 92841...

  • Page 5: Specifications

    § 25249.5, et seq.) Specifications Maximum Air Pressure 50 PSI 5.5 CFM @ 20 PSI Air Consumption 9 CFM @ 45 PSI Air Inlet 1/4" - 18 NPS Cup Capacity 33 oz. Item 92841 For technical questions, please call 1-800-444-3353. Page 5...

  • Page 6: Components And Controls

    Delayed or inadequate cleaning will permanently clog the Spray Gun. Components and Controls pattern Adjustment Knob Lock Ring Nozzle Fluid Knob Knob Trigger Cover Air Inlet paint Cup Figure A Page 6 For technical questions, please call 1-800-444-3353. Item 92841...

  • Page 7: Setup

    5. Turn on the air compressor according to more efficient, but are not required. the manufacturer’s directions and allow it to build up pressure until it cycles off. Item 92841 For technical questions, please call 1-800-444-3353. Page 7...
  • Page 8 7. Inspect the air connections for leaks. measure to attempt to discharge the tool in a Repair any leaks found. safe fashion after disconnecting to ensure that the tool is disconnected and unpowered. Page 8 For technical questions, please call 1-800-444-3353. Item 92841...
  • Page 9 NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Item 92841 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Page 10 For technical questions, please call 1-800-444-3353. Item 92841...
  • Page 11 (not included) and mix thoroughly. Use the proper thinner for the type of paint. Thin CAUTIOUSLY. Proceed slowly, adding minimal amounts at a time. DO NOT exceed the manufacturer’s thinning recommendations. Item 92841 For technical questions, please call 1-800-444-3353. Page 11...
  • Page 12 2. After setting up a piece of scrap material, squeeze the Trigger in short bursts while turning the Fluid Knob counterclockwise to set the amount of fluid. See Figure F: Fluid Adjustment. Page 12 For technical questions, please call 1-800-444-3353. Item 92841...

  • Page 13: Spraying Technique

    7. Clean Spray Gun thoroughly immediately Paint Cup and the other to operate the after EVERY use, according to Spray Gun, aim Nozzle at the workpiece. instructions on the following pages. Item 92841 For technical questions, please call 1-800-444-3353. Page 13...

  • Page 14: Maintenance

    • damaged air supply hose, • misalignment or binding of moving parts, • cracked or broken parts, and • clogged nozzle, • any other condition that may affect its safe operation. Page 14 For technical questions, please call 1-800-444-3353. Item 92841...
  • Page 15 Use old toothbrush and toothpicks to remove any paint. Solution Disposal After cleaning, dispose of cleaning solution according to the solution manufacturer’s directions and local hazardous waste standards. Item 92841 For technical questions, please call 1-800-444-3353. Page 15...
  • Page 16 Nozzle are plugged. left only 3. Damaged Needle. 3. Have qualified technician replace Needle. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Page 16 For technical questions, please call 1-800-444-3353. Item 92841...
  • Page 17 AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 92841 For technical questions, please call 1-800-444-3353. Page 17...

  • Page 18: Parts List And Diagram

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 18 For technical questions, please call 1-800-444-3353. Item 92841...

  • Page 19: Assembly Diagram

    NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Assembly Diagram Item 92841 For technical questions, please call 1-800-444-3353. Page 19...

  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents