Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Chicago Electric 69066
Summary of Contents for Chicago Electric 69066
-
Page 2: Table Of Contents
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Page 2 For technical questions, please call 1-800-444-3353. Item 69066... -
Page 3: Electrical Safety
A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Item 69066 For technical questions, please call 1-800-444-3353. Page 3... -
Page 4: Reciprocating Saw Safety Warnings
These carry important safety information. in close proximity to heart pacemaker could cause If unreadable or missing, contact pacemaker interference or pacemaker failure. In Harbor Freight Tools for a replacement. addition, people with pacemakers should: 4. Avoid unintentional starting. • Avoid operating alone. -
Page 5: Vibration Safety
If any abnormal seek medical advice as soon as possible. vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. Item 69066 For technical questions, please call 1-800-444-3353. Page 5... - Page 6 Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Outlets for 2-Prong Plug Page 6 For technical questions, please call 1-800-444-3353. Item 69066...
-
Page 7: Extension Cords
Do not cover ventilation ducts. Keep flammable objects away. Amperes WARNING marking concerning Risk of Electric Shock. Properly connect power cord n 0 xxxx/min. No Load Revolutions per Minute (RPM) to appropriate outlet. Item 69066 For technical questions, please call 1-800-444-3353. Page 7... -
Page 8: Specifications
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 14. Functions Power Indicator Light (68) Trigger (67) Shoe (31) Trigger Lock Chuck (2) Saw Blade (32) Figure 1 Page 8 For technical questions, please call 1-800-444-3353. Item 69066... -
Page 9: Important Safety Information
Saw Blade to make sure it is securely locked in the Chuck. 3. Adjust the Pivot Shoe in or out as needed. 4. Tighten the Cap Screws. Do not over tighten. Item 69066 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Work Piece And Work Area Set Up
The power cord must reach the work area with enough extra length to allow free movement while working. Page 10 For technical questions, please call 1-800-444-3353. Item 69066... -
Page 11: General Operating Instructions
12. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then 3. Follow general cutting procedure above. store the tool indoors out of children’s reach. Item 69066 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Maintenance
3. Periodically blow dust and grit out of the motor vents using dry compressed air. Wear ANSI-approved safety goggles and NIOSH-approved breathing protection while doing this. Page 12 For technical questions, please call 1-800-444-3353. Item 69066... -
Page 13: Troubleshooting
See Extension Cords in Grounding section on page 6. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 69066 For technical questions, please call 1-800-444-3353. Page 13... -
Page 14: Parts List And Diagram
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-800-444-3353. Item 69066... -
Page 15: Assembly Diagram
Assembly Diagram 15 16 9 10 11 4 5 6 Item 69066 For technical questions, please call 1-800-444-3353. Page 15... -
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.