Table of Contents
Advertisement
Grill
Lighting
Instructions
1. Before
each
use, check
all hoses
for cracks,
nicks,
cuts,
burns
or abrasions.
If a hose is damaged
in any way,
do
not use your
grill before
replacing
the hose with
an
authorized
part from the Parts
List. Also
make
sure all
gas supply
connections
are securely
tightened.
2. Familiarize
yourself
with
the safety
and Use and Care
instructions
in this manual.
Do not smoke
while
lighting
grill or checking
gas supply
connections.
3. Be sure the LP Gas tank
is filled.
4. Open the Grill Lid.
5. Check
that the end of each
Burner
Tube
is properly
located
over each
Valve Orifice.
Failure
to replace
a faulty
hose,
secure
gas
supply
connections
or to open
the
Lid
before
proceeding
to the
Lighting
Procedures
could
result
in a fire
or explosion
that
could
cause
serious
bodily
injury,
death,
or property
damage.
6. Set Control
Knobs to OFF and open the LP Gas
tank
valve SLOWLY
1/4 of a turn.
|
OFF
Open
LP
Gas_
7. Push and turn the Control
Knob to HIGH.
l
HIGH
t
OFF
((3
)
8. immediately
press
the
Electric
ignitor
for
3-4
seconds
to light
the
Burner.
PRESS
9. If ignition
does
not occur
in 5 seconds,
turn gas off at
source
and turn Control
Knobs
OFF.
Wait at least 5
minutes
for gas to clear,
then
retry.
If your grill still fails
to light turn the burner
Control
Knob(s)
and gas source
OFF and conduct
a leak test of ALL
gas connections
and gas sources
as explained
in the Use and Care
section
of this manual.
If no leaks are detected,
wait 5
minutes
for any gas to clear
and repeat
the lighting
procedure.
Back
Burner
Lighting
Instructions
1. Follow
steps
1 through
6 of the Grill Lighting
Instructions.
2. Push
and turn the Control
Knob
to ON.
Immediately
press
the Electric
ignitor
for 10 seconds
to light the
Burner.
I
ON
PRESS
3.
If ignition
does not occur
in 5 seconds,
turn gas off
at source
and turn Control
Knobs
OFF.
Wait at least
5 minutes
for gas to clear, then
retry.
If your grill still
fails to light turn the Control
Knob
and gas source
OFF and conduct
a leak test as explained
in the
Use and Care section
of this manual.
If no leaks
are detected,
wait 5 minutes
for any gas to clear
and repeat
the lighting
procedure.
4.
After Burner
is lit, turn the tank valve SLOWLY
one
more
1/4 of a turn for 1/2 of one complete
turn.
IMPORTANT:
Do not use the Back Burner
and Main
Burners
at the same
time.
Backburner
is for Rotis-
serie
Cooking
only.
Side
Burner
Lighting
Instructions
1. Follow
steps
1 through
5 of the Grill Lighting
instructions.
2. Open
Side Burner
Lid.
3. Set Control
Knobs to OFF and open
the LP Gas
tank
valve SLOWLY
1/4 of a turn.
4. Push and turn the Control
Knob to HIGH.
The built-in
spark
ignitor
will light the Burner
automatically.
5. You may have to push and turn the Control
Knob
up
to 3 or 4 times to light.
6. If ignition
does
not occur,
turn gas off at source
and
turn Control
Knobs
OFF.
Wait
at least 5 minutes
for
gas to clear, then retry.
If your grill still fails to light turn
the burner
Control
Knob
and gas source
OFF
and
conduct
a leak test as explained
in the Use and Care
section
of this manual.
If no leaks are detected,
wait
5 minutes
for any gas to clear and repeat
the lighting
procedure.
Manually Lighting
Your
Grill
By Paper
Match
To light your
gas grill by match,
insert a match
into the
Lighting
Stick and follow
steps 1 through
6 of the Grill
Lighting
instructions.
Then,
light the match
and place
Lighting
Stick
through
the Lighting
Hole on the left side
of the grill as shown
below.
Turn
the nearest
Control
Knob
to the HIGH
setting
to release
gas. The Burner
should
light
immediately.
10. After one Burner
is lit, turn the tank valve SLOWLY
one
more
1/4 of a turn for 1/2 of one complete
turn.
11. Repeat
steps
to light each
burner
individually.
Turn
other
burners
to HIGH
to light as you move
towards
the
fuel source.
Lighting
Hole
Lighting
St
Match
18
Advertisement
Table of Contents
