Page 1 Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo with in-dash six CD AM/FM stereo cassette with CD Navigation system Climate Controls Electronic automatic temperature control Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control...
Page 2: Table Of Contents
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Tires, Wheels and Loading Tire Information Changing tires Lug Nut Torque Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch...
Page 4: Introduction
For more information on Ford Motor Company and its products visit the following website: • In the United States: www.ford.com •...
Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Page 6 In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access vehicle diagnostic information through a direct connection to your vehicle when diagnosing or servicing your vehicle.
Page 7 • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent,...
Page 8 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Lower Warning Anchor Child Seat Tether Brake System Anchor Brake Fluid -...
Page 9 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...
Page 10: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 Instrument Cluster Brake system warning light: To BRAKE confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position.
Page 12 Instrument Cluster Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter. Engine coolant temperature: Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter.
Page 13 Instrument Cluster Low fuel (if equipped): Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.
Page 14 Instrument Cluster WARNING CENTER The instrument cluster is equipped with a warning center that will provide the following warning messages: Bulb warning: Displays when one of the exterior front turn/park lamps or rear brake/turn/tail lamps bulb has burned out. Depress the RESET control to return to the Trip odometer display.
Page 15: Gauges
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
Page 16 Instrument Cluster • Optional instrument cluster Trip odometer: Registers the miles (kilometers) of individual journeys. To reset, depress the RESET control. To switch the display from Trip A to the Trip B, depress the A/B control. • Standard instrument cluster •...
Page 17: Entertainment Systems
Entertainment Systems AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CD RADIO (IF EQUIPPED) 1. Seek: Press and release SEEK for previous/next strong station or track. 2. Rewind: In CD mode, press until desired selection is reached. Fast forward: In CD mode, press until desired selection is reached. TEXT: TEXT is only available when equipped with Satellite radio.
Page 18 Entertainment Systems Occupancy: Press DSP again to change the occupancy mode to optimize sound for ALL SEATS, DRIVER SEAT or REAR SEATS. Press SEL to scroll through settings. 4. Mute: Press to MUTE playing media; press again to return to playing media 5.
Page 19 Entertainment Systems Traffic: In FM mode with RDS ON, this feature allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data).Traffic information is not available in most U.S. markets. FIND Program type: In FM mode and with RDS ON, this feature allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft,...
Page 20 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed.
Page 21 Entertainment Systems CAT: CAT is only available when equipped with Satellite Radio. Your Audiophile radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Lincoln dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit available only in the continental United States.
Page 22 Entertainment Systems Treble: Allows you to increase or decrease the audio system’s treble output. Press TREB then press SEL to decrease or increase the treble levels. 4. Balance: Allows you to shift speaker sound between the right and left speakers. Press BAL then press SEL to shift sound to the left or right Fade: Allows you to shift speaker...
Page 23 Entertainment Systems FF (fast forward): Works in tape and CD modes. In the tape mode, tape direction automatically reverses when the end of the tape is reached. In CD mode, FF advances the CD within the current track. 9. Mute: Press to mute the playing media.
Page 24 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 25 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 26: Navigation System
Entertainment Systems AUDIO SYSTEM WARRANTY AND SERVICE Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. LINCOLN NAVIGATION SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Lincoln Navigation System which allows you to listen to the radio, play CDs and also navigate the vehicle using a navigation DVD.
Page 27 Entertainment Systems 1. VOL-PUSH: Press to turn the system ON/OFF. Turn to adjust the audio volume level. 2. AUDIO: Press to enter audio mode and access radio, CD, CDDJ, DVD (if equipped) settings. 3. MAP: Press to enter map mode and view your current vehicle position on the map.
Page 28 Entertainment Systems Quick Start — How to get going To play a radio station: 1. Ensure that the vehicle ignition is on. 2. Press AUDIO. 3. Select AM, FM1 or FM2. 4. Press TUNE to adjust manually up ( ) or down ( ) the frequency band.
Page 29 Entertainment Systems To load CDs: 1. Press CD OPEN CLOSE at the bottom of the screen to load a CD. (The screen will open). 2. Press LOAD and select the desired slot. Or, press and hold LOAD to auto load all available slots. The slot indicator lights blink rate will increase when the system is ready to accept a disc.
Page 30 Entertainment Systems 2. Press DEST. The warning screen will appear. After reading, press AGREE. The screen will show a map with your current location. Press DEST again. 3. Select the desired type of destination entry. You may select “Address”, “Point of Interest”, “Emergency”...
Page 31 Entertainment Systems 4. Press DEST at the bottom of the map screen. 5. Choose the desired route by pressing the NEXT button (if it appears). There can be up to three alternative routes. 6. Press START to begin the navigation guidance. To adjust the voice guidance volume: VOL PUSH AUDIO...
Page 32 Entertainment Systems Press VOICE briefly (on your steering wheel controls) and the voice icon appears on the Navigation display. Press REPEAT to hear the previous command repeated from the navigation system. The voice activated command feature will not operate if a map DVD is not inserted into the navigation DVD unit.
Page 33 Entertainment Systems Commands that jump over screens: • Current position • Current location • Map While in navigation map mode, the following commands are available: • Zoom in • Zoom out • Minimum scale • Maximum scale • North up •...
Page 34 Entertainment Systems • Chinese food • Continental restaurant • Continental food • French restaurant • French food • Italian restaurant • Italian food • Japanese restaurant • Japanese food • Mexican restaurant • Mexican food • Seafood restaurant • Seafood •...
Page 35 Entertainment Systems • Change to arrow guidance • Change to arrow guide • Turn list guidance • Turn list guide • Change to turn list guidance • Change to turn list guide • Entire route map • Entire route • Route overview •...
Page 36 Entertainment Systems Volume/power control Press knob to turn the audio system on/off. Turn to raise or lower volume. The levels will be displayed on the screen. To activate the navigation mode, press MAP or DEST. To adjust the navigation voice output level, select the NAV MENU button via the map screen.
Page 37 Entertainment Systems 3. SCV is located in the middle of the screen. Press to turn on. 4. Select setting 1 to 7 or turn off. The recommended level for the speed compensated volume is from level 1 through level 3. When activated, level 1 is the minimum setting and level 7 is the maximum setting.
Page 38 Entertainment Systems Tune adjust Press TUNE to manually move down/up ( ) the frequency band. In CD mode, press TRACK to select the previous/next ( Scan Press SCAN for a brief sampling of SOUND all listenable stations and CD tracks. SEEK TUNE Press again to disable and remain on...
Page 39 Entertainment Systems Starting autoset memory preset 1. Select a frequency band using SOUND AM/FM1/FM2. SEEK TUNE AUTO SET SCAN PRESET SCAN TRAFFIC INFO SET PTY 87.9 89.9 98.1 98.5 106.3 107.9 2. Press AUTO SET. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Page 40 Entertainment Systems Traffic function Select TRAFFIC for traffic SOUND information broadcast from certain SEEK TUNE stations which will automatically AUTO SET SCAN PRESET SCAN interrupt radio or CD playback at a preset volume level. TRAFFIC INFO SET PTY 87.9 89.9 98.1 98.5 106.3...
Page 41 Entertainment Systems • All • Classical • Country • Information • Jazz • Religious • Rock • Soft • Top 40 Once PTY has been programmed, press SEEK ( ) or SCAN to initiate a search up or down the frequency. Preset scan and Autoset also initiate PTY searches.
Page 42 Entertainment Systems 4. Press +/— to increase/decrease the levels. Bass : Allows you to increase or decrease the audio system’s bass output. Treble : Allows you to raise or lower the audio system’s treble output. Fade : Allows you to adjust the amount of sound emitted from the front and rear speakers.
Page 43 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 44 Entertainment Systems Press CD. CD play will begin where it stopped last. Loading a CD: 1. Press CD OPEN CLOSE on the bezel. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 45 Entertainment Systems 2. The navigation screen will fold down, allowing you access to the in-dash six CD system. 3. Press LOAD and the desired CD slot number. The indicator light will blink slowly at first, then quickly, signaling the system is ready. 4.
Page 46 Entertainment Systems Rewind/fast forward in CD mode Press to reverse or advance ) in the current CD track. Scan feature in CD mode Press SCAN to hear a brief sampling of all tracks on the current CD. Press again to disengage and remain with the current track.
Page 47 Entertainment Systems Pause In CD mode, press PAUSE to pause the current track. Press again to continue playing. Map mode Map display information To access the map display, press MAP on the bezel. Once pressed, the current map display will appear on the screen showing the current vehicle location.
Page 48 Entertainment Systems • Touch one of the arrow buttons repeatedly for the map to be displayed again at the final zoom level. • Touch one of the segments of the scale indicator for the map to be displayed at the selected zoom level. Additional map function buttons To initiate the display of additional map function buttons, tap the map...
Page 49 Entertainment Systems Route preferences After entering a destination, the Route preferences will appear on the screen showing what is currently selected. You may choose to activate/deactivate selections which the system will factor in when calculating your route. Those options are: •...
Page 50 Entertainment Systems You will be able to view the information (if available) as well as choose to store the destination as a memory point by pressing OK. Screen symbols Navigation symbol — Indicates the current vehicle position and points to the direction in which the vehicle is currently traveling.
Page 51 Entertainment Systems Avoid areas or points — The “X” symbol indicates a point. to be avoided in route calculations. If the avoid point is enlarged to an avoid area, it will appear on the screen as a shaded box. Way point symbol — Indicates the location of a way point (locations you wish to visit in route to your ultimate destination) on the map.
Page 52 Entertainment Systems Once pressed, the Navigation Menu will display showing the following options: • Route Options/Preferences • Navigation Set Up • Display Options • Stored Locations • On Route Scroll • Voice Guidance/Volume Depending upon whether or not a route is active will determine if route options/route preferences is contained on the Navigation Menu.
Page 53 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Navigation set up The Navigation Set up screen will allow you to make adjustments to...
Page 54 Entertainment Systems Restore system defaults Resets all system user-selectable options to the default (automatic) values (i.e. guidance, voice, search area and route preferences). Calibration This feature is helpful if the car has been towed, or if you notice it is not registering at the correct vehicle location on the map.
Page 55 Entertainment Systems Display Options The Display Options screen will allow you make adjustments to the navigation display screen. You can choose from: • Map Mode (Dual or Full) • Guidance Mode (Arrows or Turn list) • Guidance Display (On or Off) •...
Page 56 Entertainment Systems In this screen, you can select from Memory Points, Special Memory Points, Home, Avoid Area, Destination and Way Point, or Previous Destination. Please refer to the Destination menu section for a complete description of the functions. On route scroll The system automatically scrolls through the entire planned navigation route either forwards or...
Page 57 Entertainment Systems Voice guidance/volume Allows you to turn the voice guidance option on/off and to determine the volume level of the guidance voice prompts. To adjust: 1. Press the MAP hard key. 2. Press “Nav Menu” at the bottom left hand corner of the screen. 3.
Page 58 Entertainment Systems Home To set home for the first time: 1. Press MAP. 2. Press “Nav. Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “Add”. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 59 Entertainment Systems 6. Select the desired menu item you wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). 7. Enter the required details. 8. Press OK to set the home position. To view home, press the home icon (house) on the Destination Entry screen.
Page 60 Entertainment Systems To view the set home position 1. Press MAP. 2. Press “Nav. Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “List”. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 61 Entertainment Systems Deleting a home location 1. Press MAP. 2. Press “Nav. Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “Delete”. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 62 Entertainment Systems 6. Press YES to confirm. Special memory points There are five possible special memory points that you can set. To set a memory point: 1. Press the MAP hard key. 2. Press “Nav. Menu”. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 63 Entertainment Systems 3. Press “Stored Locations”. 4. Press “Special Memory”. 5. Press “Add” and select a position. 6. Select point 1–5. 7. Input a destination. 8. Press OK. Once all five special memory points are entered, the “Add” control will read as “Full”.
Page 64 Entertainment Systems 3. Press “Stored Locations”. 4. Press “Special Memory”. 5. Press “Delete”. The list will display. 6. Select the special memory point to delete. 7. Press “Del. all” to delete all entered special memory points. 8. Press “Yes” to confirm. Detour options You may engage the detour option once a route has already been calculated by the system.
Page 65 Entertainment Systems Press DETOUR to activate. Use the soft controls to select and enter the number of miles you want to deviate off of the current road. Press DETOUR to confirm the selection and to activate the detour around the specified areas. Press NEW ROUTE if you would like the system to plan a different route.
Page 66 Entertainment Systems Avoiding an area while under guidance For one reason or another, you may choose to avoid a certain area while in route to your destination. To select the area to avoid: • From the MAP screen, press Nav Menu.
Page 67 Entertainment Systems Deleting areas to avoid To delete a selection from the “Avoid area” list: • From the stored locations menu, select “Avoid area”. • Press DELETE • Select the desired area to be deleted. • Press DEL. ALL to delete all stored areas.
Page 68 Entertainment Systems Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped).
Page 69 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Destination entry Selecting a destination Press DEST to set a destination.
Page 70 Entertainment Systems Search area The mapped areas covered by your map DVD are reflected in the Search Area map that is displayed on the Destination Entry screen. Your navigation system uses a regional search area. This area is the area from which navigational directions will be used.
Page 71 Entertainment Systems Points of interest (POI) Select “Point of Interest” from the Destination Entry Menu. In this next menu, you will have the following options: • By Name— Enter POI name on the keyboard. Touch “List” to display the list of matching points of interest.
Page 72 Entertainment Systems Deleting stored locations Your navigation system allows you to delete any stored locations (previous destinations, memory points, special memory points, home, avoid areas, destination and way points, etc.) To delete any of these stored locations: 1. Press the MAP hard key. 2.
Page 73 Entertainment Systems 4. Select the desired item you wish to delete (previous destination, memory point, etc.). 5. Press “Delete” at the bottom of the screen. 6. The list of stored locations will be displayed. 7. Select (touch) the entry to be deleted.
Page 74 Entertainment Systems Adding a memory point You may add more memory points to be stored in the system. 1. With the map displayed, touch your finger to the screen to scroll to the desired location. When you reach the desired location, remove your finger from the screen and the map will stop scrolling.
Page 75 Entertainment Systems 4. Select “Memory Point”. 5. Press “Add” at the bottom of the screen. 6. Select the desired menu item. 7. Enter/select any required details. The new point will be added to the stored list of memory points. 8. Press OK. The new point will be added to the list of stored memory points.
Page 76 Entertainment Systems 3. Press “Stored locations”. 4. Press “Memory Point”. 5. Press LIST 6. Select the desired entry to view its location details. Sorting memory point lists 1. Access the desired list. 2. Press the button to sort the list as desired (i.e.
Page 77 Entertainment Systems current vehicle location. When sorting by icon, the icons are listed in the order they appear on the icon selection screen. Choosing from the icon list After selecting a location, press ICON to edit. There will be 15 normal and three sound icons displayed.
Page 78 Entertainment Systems Freeway Entrance/Exit To set a freeway entrance or exit as a destination: 1. Press the DEST hard key. 2. Press “ Next page” to access the second page of the Destination Entry menu. 3. Select “Freeway Entrance/Exit”. 1. Enter freeway name— Enter the freeway name using the keyboard.
Page 79 Entertainment Systems Destination and way points The Store Dest. & Way Point menu is used after a destination or way point has been entered for the first time using the Destination Entry menu. You can store and delete destinations and way points (locations you wish to visit in route to your ultimate destination).
Page 80 Entertainment Systems Editing and changing order of way points and destination Press “Chg. Order” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display.
Page 81 Entertainment Systems Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination. Press “Next”...
Page 82 Entertainment Systems Menu mode To access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen.
Page 83 Entertainment Systems • Screen off — Allows you to turn off the navigation screen. System setup The system set up menu contains the following user settings: • Audible Feedback — Press to activate audible voice navigation commands. Press again to deactivate.
Page 84 Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines. Do not attempt to service, repair or modify the system. See your Ford or Lincoln Mercury dealer. The driver must not attempt to operate any detailed operation of the navigation system while the vehicle is in motion.
Page 85 Ford or Lincoln Dealer. Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 86 Entertainment Systems traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal. • Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.
Page 87 Entertainment Systems • Not harmful but not recommended- ammonia cleaner, neutral detergent. • Harmful to system and not recommended- acid cleaner, alkali cleaner, benzene cleaner. Do not clean any part of the system with benzene, paint thinner or any other solvent. Do not spill liquids of any kind onto the unit.
Page 88: Climate Controls
Climate Controls DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM (IF EQUIPPED) 1. A/C control: Press to turn on and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature. 2. Recirculation control: Press to engage/disengage.
Page 89 Climate Controls 5. DUAL zone selector: Press to DUAL toggle the system between single zone and dual zone control. (Defrost): Distributes outside air through the windshield defroster ducts and the demister outlets. Can be used to clear ice or fog from the windshield.
Page 90 Climate Controls 15. Fan Speed: Press to manually increase/decrease fan speed. In manual mode, the display will show with a bar graph to indicate fan speed. Fan speed can be manually adjusted in AUTO mode. To allow the system to automatically control fan speed, press AUTO. 16.
Page 91 Climate Controls 1. A/C control: Press to turn on and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature. 2. Recirculation control: Press to engage/disengage. Used to manually enable or disable recirculated air operation.
Page 92 Climate Controls Airflow direction control: Press to toggle through the air distribution modes listed below. The selected mode will illuminate in the display. : Distributes air through the windshield defroster ducts, demister outlets and the front and rear seat floor ducts. The system will automatically provide outside air to reduce window fogging.
Page 93 Climate Controls show . This allows the seats to automatically heat or cool based on the climate control temperature selected. Press either control to disengage. 14. Driver’s side temperature control: Controls the temperature on the driver side of the vehicle in dual zone and controls the temperature of the entire vehicle in single zone.
Page 94 Climate Controls • Remove any snow, ice or leaves from the air intake area at the base of the windshield. • With the ignition in the OFF position after operating the vehicle, some vehicle sounds related to the climate control system may be heard. •...
Page 95: Rear Window Defroster
The filter is located just in front of the windshield under the cowl grille on the passenger side of the vehicle. For more information, or to replace the filter, see your Ford or Lincoln Mercury dealer. 2005 Lincoln LS (dew)
Page 96: Lights
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 97 Lights Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is pulled toward you and is in any of the following positions: • Parking lamps • Low beams • Autolamps (when active) Foglamps will turn off when the highbeams are activated.
Page 98 Lights Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during parklamp, headlamp and autolamp operation. • Rotate up to brighten. • Rotate down to dim. •...
Page 99: Turn Signal Control
Lights tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens (use the low beam center mark). 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood.
Page 100: Bulb Replacement
Lights INTERIOR LAMPS Map lamps The map lamps and controls are located on the dome lamp. Press the controls in front of each map lamp to activate the lamps. BULBS Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur.
Page 101 Lights Function Trade Number Foglamp 9145 Foglamp (LSE only) H11LL Tail lamp, brakelamp, side lamp 3157K Rear turn lamp 3157 A/K (amber) Backup lamp License plate lamp High-mount brakelamp LED* Map lamp (with moon roof) Rail lamp (rear) Map lamp (front) Sun visor lighted mirror lamp E9SB-13465-BA Glove compartment...
Page 102 Install the new bulb in reverse order, while also replacing the seal on the bulb retaining cover. The kits for replacement seals are available at Lincoln or Ford dealers. Replacing HID headlamp bulb (if equipped) The low beam headlamps on your vehicle use a “high intensity discharge”...
Page 103 Install the new assembly in reverse order, while also replacing the seal on the bulb retaining cover. The kits for replacement seals are available at Lincoln or Ford dealers. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 104 Lights Replacing front parking lamp/turn signal lamp bulbs 1. Remove the headlamp assembly as described under Replacing headlamp bulbs earlier in this section. 2. Turn the bulb counterclockwise and pull it straight out of the headlamp assembly. Install the new bulb in reverse order. Replacing foglamp bulbs 1.
Page 105: Driver Controls
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: •...
Page 106 Driver Controls 2. Firmly press the release tab from the bottom side of the wiper arm to unlock wiper blade from wiper arm. 3. Pull the wiper blade down toward the windshield to remove it from the arm. 4. Attach the new wiper to the wiper arm and reposition the clip until it locks.
Page 107 Driver Controls refer to the Message Center in the Driver Controls chapter. When the key is inserted into the ignition, the column will return to the previous setting. Note: The easy entry/exit feature will prevent the steering wheel from returning to the memory position until the key is inserted into the ignition.
Page 108 Driver Controls Storage compartment Press to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object. Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet for this will damage the outlet and blow the fuse.
Page 109: Power Windows
Driver Controls POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Page 110: Mirrors
Driver Controls When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Restoring the Express up functionality Under low battery power conditions, Express Up only functionality may be lost.
Page 111 Driver Controls the clear state to the non-glare state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind, it will automatically adjust (darken) to minimize glare at night only. The mirror will automatically return to the clear state whenever the vehicle is placed in R (Reverse)(when the mirror is on).
Page 112 Driver Controls The compass reading will remain fixed when significant levels of magnetic interference are experienced (such as steel bridges). The compass will return to normal operation upon leaving the magnetized area. If highly magnetized items (such as magnetic mount antennas) are placed very near the compass the display will change to “C”.
Page 113 Driver Controls 1. Start the vehicle. 2. Press and hold the COMP side of the control until “C” appears in the mirror display. 3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until the display reads a direction. 4.
Page 114: Speed Control
Driver Controls Fold-away mirrors (if equipped) Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position.
Page 115 Driver Controls Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release 2.
Page 116 Driver Controls Resuming a set speed Press the RES control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed:...
Page 117 Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal . This will not erase your vehicle’s previously set speed.
Page 118 Driver Controls In AM, FM1, or FM2 mode: • Press to select preset MUTE stations within the selected radio band. In Tape mode: • Press to select the next selection on the tape. MEDIA In CD mode: • Press to select the next selection on the CD.
Page 119 Driver Controls Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation control features when the vehicle is equipped with the navigation feature. Audio control features Press MEDIA to select: • AM, FM1, FM2, or •...
Page 120 Driver Controls Navigation control features Press and hold VOICE until the voice icon appears to use the navigation voice guidance. Press REPEAT control to hear previous command repeated from the navigation system. MOON ROOF (IF EQUIPPED) To open the moon roof: •...
Page 121 Driver Controls • To close from the vent, intermediate and full open positions, push the rear portion of the control forward. Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. When closing the moon roof, you should verify it is free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Page 122 Driver Controls Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink buttons be erased for security purposes, refer to Programming in this section.
Page 123 Driver Controls 5. Press and hold the just-trained HomeLink button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink button is pressed and released. Note: To program the remaining two HomeLink buttons, begin with Step 2 in the “Programming”...
Page 124 Driver Controls seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink . The indicator light will flash slowly and then rapidly after HomeLink accepts the radio frequency signal. • Proceed with Step 4 in the “Programming” section. Operating the HomeLink Wireless Control System To operate, simply press and release the appropriate HomeLink button.
Page 125: Message Center
Driver Controls For questions or comments, contact HomeLink at www.homelink.com or 1–800–355–3515. CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment.
Page 126 Driver Controls RESET Press this control to select and reset functions shown in the FUEL, SETUP and STATUS controls. SETUP Press this control for the following displays: • Units (English/Metric) • Autolocks • Easy Exit Seat (if equipped) • Autolamp Delay •...
Page 127 Driver Controls Message center functions Dist To Empty (DTE) Selecting this function from the FUEL control estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel.
Page 128 Driver Controls You may notice gradual improvement in fuel economy over the course of your vehicle’s break-in period (approximately 1,000 miles [1,600 kilometers]). 1. Press the FUEL control to display miles to empty. Press again to display average fuel economy. 2.
Page 129 Driver Controls Easy exit seat (if equipped) 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the easy entry/exit ON or OFF. Autolamp delay 1. Select this function from the SETUP control for the current display mode.
Page 130 Driver Controls System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds.
Page 131 Driver Controls Warnings Status Low brake fluid level Warning returns after the ignition key is turned from OFF to RUN Check tail lamps Check brake lamps Check front turn lamps Check side repeater lamps (if equipped) Check rear turn lamps Check Traction Control Check AdvanceTrac (if equipped)
Page 132 Driver Controls PASSENGER REAR DOOR AJAR. Displayed when the passenger side rear door is not completely closed. PARK BRAKE ON & NEED SERVICE. Displayed when the park brake is ON and malfunctioning. If the warning stays on or continues to come on, contact your dealer as soon as possible.
Page 133 Driver Controls LOW BRAKE FLUID. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. CHECK TAIL LAMPS. Displayed when the tail lamps are activated and at least one is burned out.
Page 134 Driver Controls and 0%, the CHANGE A/C FILTER SOON message will be displayed. When A/C filter life left reaches 0%, the A/C FILTER CHANGE REQUIRED message will be displayed. To reset the A/C filter monitoring system to 100% after each A/C Filter change: 1.
Page 135 Driver Controls 3. After a successful reset, the message center will display OIL LIFE SET TO 100%. SERVICE PARK BRAKE. Displayed when the park brake needs servicing. If the warning stays on or continues to come on, contact your dealer as soon as possible. APPLY PARK BRAKE.
Page 136 Driver Controls The remote trunk release control and power door locks will be disabled when the vehicle perimeter alarm system is armed. This control will not work until the vehicle perimeter alarm system is disarmed. Refer to Perimeter Alarm System in the Locks and Security chapter. FUEL DOOR RELEASE Press the remote fuel door release control on the instrument panel to...
Page 137 Driver Controls 2. Push the ashtray drawer in to close. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: 1. Cupholders 2. Sliding arm rest (lift latch to slide forward or rearward) Note: Slide the arm rest to the rearward position to open the utility compartment 3.
Page 138 Driver Controls CARGO NET (IF EQUIPPED) The cargo net secures lightweight objects in the cargo area. This net is not designed to restrain objects during a collision. There are four straps on the net and six anchors in the trunk that can be used for securing different sized objects.
Page 139: Locks And Security
Locks and Security KEYS Your vehicle is equipped with two master keys and a valet key lock system. The master key will access the driver’s door, trunk, glove box, remote trunk release control and ignition. The valet key will access door and ignition only.
Page 140 Locks and Security seconds to begin to open all the windows and moonroof. Releasing control on the remote entry transmitter, or returning the key to the center position will stop all motion. Note: The ignition must be in the 2 (OFF) position and the accessory delay feature must not be activated in order for this feature to operate.
Page 141 Locks and Security Childproof door locks • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on the rear edge of each rear door and must be set separately for each door.
Page 142 Locks and Security Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.
Page 143 Locks and Security The remote entry system allows you to perform the following tasks using the remote entry transmitter: • unlock the vehicle doors. • lock all the vehicle doors. • open the trunk. • activate the personal alarm. • open all windows and moonroof (if equipped).
Page 144 Locks and Security 2. Press and release again within five seconds to unlock all the doors. The remote entry system comes with an illuminated entry feature. This feature turns on the puddle lamps and the interior lamps for 20 seconds or until the ignition is turned to the 5 (START) position.
Page 145 Locks and Security Sounding a panic alarm Press on the remote transmitter to activate the alarm. Press a second time to deactivate the alarm. You may also deactivate the alarm in the following ways: • Press on the remote transmitter. •...
Page 146 Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery.
Page 147 Locks and Security To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 4 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 4 (RUN).
Page 148 Locks and Security • the ignition is in the 4 (RUN) position, • you shift into forward or reverse, and • the vehicle speed is greater than 3 mph (5 km/h). Relock The autolock feature repeats when: • either door is opened then closed while the ignition is in the 4 (RUN) position, and •...
Page 149 Locks and Security 2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press any control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to associate with the Driver 1 or Driver 2 positions.
Page 150 Locks and Security 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. Enter a sixth digit to indicate which personality feature should be recalled by the personal code. Note: The lock motors will cycle, locked then unlocked.
Page 151: Anti-Theft System
Note: The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to...
Page 152 If two previously programmed coded keys are not available, you must take your vehicle to an authorized Ford dealer to have the spare coded key(s) programmed. Please read and understand the entire procedure before you begin.
Page 153 Locks and Security 1. Insert the first previously programmed coded key into the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in the 4 (RUN) position for at least three seconds, but no more than ten seconds). 2. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition.
Page 154 Locks and Security The system is ready to arm whenever key is removed from the ignition. Any of the following actions will prearm the alarm system: • Press the control on the remote entry transmitter. • Press the driver or passenger interior power door lock control while that respective door is open, then close the door.
Page 155: Seating And Safety Restraints
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Page 156 Seating and Safety Restraints Using the manual lumbar support (if equipped) The lumbar control is located on the front of the seat cushion. Turn to adjust lumbar support. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat.
Page 157 Seating and Safety Restraints Rotate the vertical control to adjust the seatback. • Driver • Passenger Slide the control forward or backward to move the seat forward or backward. • Driver • Passenger Move the control up or down to move the seat up and down.
Page 158: Electronic Automatic Temperature Control
Seating and Safety Restraints Deactivating/activating the easy entry/easy exit feature The easy entry/easy exit feature can be turned off or on through the vehicle message center (if equipped). If your vehicle does not have a message center, the feature can be turned off or on by your dealer. Memory seats/steering column/mirrors/adjustable pedals (if equipped) This system allows automatic...
Page 159 Seating and Safety Restraints Climate controlled seats air filter replacement The climate controlled seat system includes air filters that must be replaced periodically. Refer to the Scheduled Maintenance Guide for more information. • There is a filter located under each front seat. •...
Page 160 Seating and Safety Restraints • Remove filter. To install a filter: • First, position the filter in it’s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Page 161 Seating and Safety Restraints Push control to lower head restraint. Rear heated seats (if equipped) • Push the indicated side of the button for low heat. • Push again to deactivate. • Push the indicated side of the button for high heat. •...
Page 162: Safety Restraints
Seating and Safety Restraints To lower the seatback(s), pull the release handle(s) located inside the trunk. Fold the seatback(s) down. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback.
Page 163 Seating and Safety Restraints • Driver and front passenger side air bags • Driver and passenger side air curtains (if equipped) • Front safety belts with pretensioners, energy management retractors, and safety belt usage sensors • Driver’s seat position sensor •...
Page 164 Seating and Safety Restraints allows your Personal safety system to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage air bags and safety belt pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Personal safety system to tailor the deployment level of the driver dual-stage air bag based on seat position.
Page 165 Seating and Safety Restraints Warning light section in the Instrument cluster chapter. Routine maintenance of the Personal safety system is not required. The Restraints control module (RCM) monitors its own internal circuits and the circuits for the air bag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, and driver seat position sensor.
Page 166 Seating and Safety Restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair.
Page 167 Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. Energy management feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.
Page 168 Seating and Safety Restraints Automatic locking mode How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 169 Seating and Safety Restraints After any vehicle collision, the combination lap and shoulder belt system at all passenger seating positions must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly, in addition to other checks for proper seat belt system function.
Page 170 Seating and Safety Restraints Front safety belt height adjustment The driver and front seat outboard positions are equipped with a height adjuster. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, push the button and slide the height adjuster up or down.
Page 171 Seating and Safety Restraints If... Then... The driver’s safety belt is The safety belt warning light and buckled before the ignition indicator chime remain off. switch is turned to the RUN position... BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function.
Page 172 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare 36700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers.
Page 173 Seating and Safety Restraints Reasons given... Consider... “I’d rather be thrown Not a good idea. People who are ejected are clear” 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. Do not sit on top of a buckled safety belt to avoid the BeltMinder chime.
Page 174 (if equipped), shoulder belt guide on seatback (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced.
Page 175: Air Bags
Seating and Safety Restraints Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. For proper care of soiled safety belts, refer to Interior in the Cleaning chapter.
Page 176 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifying or adding equipment to the front end of the vehicle...
Page 177 Seating and Safety Restraints Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
Page 178 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 179 Seating and Safety Restraints • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system wiring (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power, the air bag ignitors and safety belt pretensioners.
Page 180 Do not attempt to service, repair, or modify the air bag SRS, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle should always wear their safety belts even when an air bag SRS is provided.
Page 181 Seating and Safety Restraints not of the type sufficient to cause activation. Side air bags are designed to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation.
Page 182 Seating and Safety Restraints Side air curtain system (if equipped) Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag.
Page 183 Do not attempt to service, repair, or modify the side air curtain system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a side air curtain. See your Ford or Lincoln Mercury dealer.
Page 184 Seating and Safety Restraints How does the side air curtain system work? The design and development of the side air curtain system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group.
Page 185 Seating and Safety Restraints impact collisions. The seat-mounted side air bag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collision. The side air curtain system SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air curtain and seat-mounted side air bag inflation.
Page 186: Child Restraints
Seating and Safety Restraints Any difficulty with the system is indicated by one or more of the following: • The readiness light (same light as used for front air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned to the RUN position.
Page 187 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 188 Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? •...
Page 189 Seating and Safety Restraints The shoulder belt should cross the chest, resting snugly on the center of the shoulder. The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Page 190 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LATCH and tether anchors.
Page 191 Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 192 Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 193 Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 194 Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.
Page 195 Seating and Safety Restraints 6. Install the child safety seat tightly using the LATCH anchors or safety belts. Follow the instructions in this chapter. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases.
Page 196 LATCH attachments. Two plastic LATCH guides can be obtained at no charge from any Ford or Lincoln/Mercury dealer. They snap onto the LATCH lower anchors in the seat to help attach a child seat with rigid attachments.
Page 197: Tires, Wheels And Loading
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 198 Tires, Wheels and Loading The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 199 (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company. Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and...
Page 200 (if equipped), at least monthly and before long trips. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial type tire pressure gauge rather than a stick type tire pressure gauge.
Page 201 Tires, Wheels and Loading pressure should never be set lower than the recommended pressure on the tire label or certification label. When weather temperature changes occur, tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
Page 202: Tire Information
Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 203 Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 204 Tires, Wheels and Loading • Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise •...
Page 205 Tires, Wheels and Loading 3. Lift the trunk cargo cover and remove the spare tire, jack and lug wrench. 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 206 Tires, Wheels and Loading 5. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. Never use the rear differential as a jacking point. To lessen the risk of personal injury, do not put any part of your body under the...
Page 207: Lug Nut Torque
M12 x 1.5 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel.
Page 208 Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1.
Page 209 Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) 81 mph (130 km/h) 87 mph (140 km/h) 99 mph (159 km/h) 106 mph (171 km/h) 112 mph (180 km/h) 118 mph (190 km/h)
Page 210 Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 ⁄...
Page 211 Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks.
Page 212 Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 213 Tires, Wheels and Loading the road in adverse (wet, snowy, etc.) conditions. Visually check your tires for uneven wear, looking for high and low areas or unusually smooth areas. Also check for signs of tire damage. When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to prevent your vehicle from skidding and hydroplaning.
Page 214 If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have a qualified technician at a Ford or Lincoln Mercury dealer check the wheel alignment periodically.
Page 215 Tires, Wheels and Loading help your tires wear more evenly, providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km). • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) •...
Page 216: Vehicle Loading
Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 217 Tires, Wheels and Loading capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Safety Certification Label and Tire Label: Base Curb Weight –...
Page 218 Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 219 Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door.
Page 220 Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door.
Page 221 Tires, Wheels and Loading Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb.
Page 222 Tires, Wheels and Loading The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity. You decide to go golfing. Is there enough load capacity to carry you, 4 of your friends and all the golf bags? You and four friends average 220 lb.
Page 223: Trailer Towing
If a distance of 50 miles (80 km) or a speed of 35 mph (56 km/h) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. Improper removal/installation of the driveshaft may cause damage to the driveshaft and internal transmission components.
Page 224: Driving
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. (The steering wheel will not lock after key removal.) 2. OFF, shuts off the engine and all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Page 225 Driving Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas.
Page 226 Driving • Turn the key to 4 (ON) without turning the key to 5 (START). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Page 227: Brakes
Driving 3. After idling for a few seconds, apply the brake, shift into gear and drive. Using the engine block heater (if equipped) An engine block heater warms the engine coolant which aids in starting and heater/defroster performance. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -10°F (-23°C) or below.
Page 228 Driving keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a little farther as soon as ABS braking is done and normal brake operation resumes. These are normal characteristics of the ABS and should be no reason for concern.
Page 229 Driving Parking brake To set the parking brake, pull the lever up. To release the parking brake, make sure the ignition is turned to ON, depress the brake pedal, then gently push the parking brake lever down. The BRAKE warning lamp will BRAKE illuminate and will remain illuminated until the parking brake...
Page 230 Driving • Do not operate the vehicle with a low power steering pump reservoir fluid level (below the MIN mark on the reservoir). If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: •...
Page 231 Driving The Traction Control switch, located on the center console by the gearshift lever, has an indicator light that illuminates when the system is off. The Traction Control system will automatically turn on every time the ignition is turned off and on. If you should become stuck in snow or ice or on a very slippery road surface, try switching the Traction Control...
Page 232 Driving AdvanceTrac enhances your vehicle’s stability during maneuvers that require all available tire traction, like in wet/snowy/icy road conditions and/or when performing emergency maneuvers. In an emergency lane-change, the driver will experience better overall vehicle traction, and have better control of the vehicle. The AdvanceTrac system helps the driver maintain steering control if the vehicle begins to slide excessively left or right or spin out.
Page 233 Driving indicator light in the instrument cluster remains on while the engine is running, have the system serviced immediately. Pressing the control once will disable the AdvanceTrac stability enhancement and the engine power reduction portion of the traction enhancement feature; the brake portion of the traction enhancement feature will still function normally.
Page 234: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the RUN position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and the brake pedal depressed: 1.
Page 235 Driving Driving with a 5–speed automatic transmission This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected.
Page 236 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 237 Driving • Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed. 1 (First) This position allows for first gear only. • Provides maximum engine braking. • Will not downshift into first gear at high speeds; will cause the transmission to downshift to a lower gear, then allows for first gear when the vehicle reaches slower speeds.
Page 238 Driving Manual shift mode With the gearshift lever in D5 (Overdrive), the gearshift lever can be moved to the right and into the manual shift mode. The transmission will remain in the manual shift mode until the gearshift lever is moved back to D5 (Overdrive).
Page 239 Driving • If shifter (-) is tapped more than once in rapid succession, the transmission will downshift only into the next lower gear, then when the vehicle reaches a speed below a calibrated entry speed, the transmission will allow a downshift into the next lower gear if again selected by the driver.
Page 240 Driving To help avoid personal injury, always use caution when in R (Reverse) and when using the rear park assist. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting objects to avoid damaging the vehicle.
Page 241 Driving The rear park assist is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. A park assist control allows the driver to disable the system only when the ignition is ON, and the gear selector is in R (Reverse).
Page 242: Roadside Emergencies
50,000 miles (80,000 km) on Lincoln vehicles. Roadside assistance will cover: • a flat tire change with a good spare (except Ford GT which has a tire inflation kit) • battery jump start • lock-out assistance (key replacement cost is the customer’s responsibility) •...
Page 243: Fuel Pump Shut-Off Switch
1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673;...
Page 244: Fuses And Relays
Roadside Emergencies This switch is located in the driver’s footwell, behind the kick panel. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button.
Page 245 Roadside Emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard Maxi Fuse link maxi rating fuses fuses fuses cartridge fuses Grey Grey — — — Violet Violet — — — Pink Pink — — — — — —...
Page 246 Roadside Emergencies OWNER'S MANUAL RELAY 1 The fuses are coded as follows. Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Starter relay coil Radio ABS/TCS/AdvanceTrac Cluster, Powertrain Control Module (PCM) relay, Fuel pump relay, REM Restraints Control Module (RCM) OBD II DDM, DSM, Anti-theft LED, Power mirror switch, Electric Park Brake switch, PCM...
Page 247 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Left front turn, Left front sidemarker, Left front park lamps Left front high beam Electrochromic mirror Cluster DATC O/D cancel, ABS/Traction-Assist switch Heated seat controls, Climate control seat module RCM, Alternator warning lamp Radio, CIA, Navigation unit...
Page 248 Roadside Emergencies Front power distribution box The front power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Page 249 Roadside Emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 10A* A/C clutch, Coolant control valve, Auxiliary coolant pump — Not used 15A* Fog lamp 20A* Horn 15A* Fuel injectors, Electric cooling fan, Mass Air Flow (MAF) sensor 15A* Transmission solenoid, EGR...
Page 250 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 30A** Heated wiper park 30A** ABS module — Not used 30A** Blower motor — Not used — Not used 30A** Electric park brake 30A** Wiper motor 30A** Starter solenoid 40A** ABS motor —...
Page 251 Roadside Emergencies The trim panel must be removed and the carpet on the front passenger side must be lifted to access this fuse. See a qualified technician to have this fuse replaced, if necessary. Rear power distribution box The rear power distribution box is located in the luggage compartment under the spare tire well cover.
Page 252 Roadside Emergencies 1 2 3 4 5 6 7 8 9 > PBT < 10 11 12 13 14 15 16 17 18 RELAY MINI-FUSE CARTRIDGE FUSE RELAY RELAY RELAY RELAY RELAY RELAY DIODE 01 DIODE 02 SEE OWNER'S MANUAL CONSULTER LA GUIDE The high-current fuses are coded as follows.
Page 253: Jump Starting
Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 20A* Subwoofer amp 30A* THX amp, Subwoofer amp 20A** REM - Left rear window 30A** Front window motors 20A** Driver lumbar, Power seats 20A** Ignition switch 30A** SSP4 30A** SSP3 40A** P-J/B...
Page 254 Roadside Emergencies Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter. Preparing your vehicle Your battery is located in the trunk of your vehicle. When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy.
Page 255 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 256 Roadside Emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 257 Roadside Emergencies 4. Make the final connection of the negative (-) cable to the spare tire tie-down stud. (Your vehicle may be equipped with a plastic cap on top of the tire tie-down stud. This cap must be removed prior to attaching the cable to the stud.) Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 258 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the spare tire tie-down stud. 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Page 259 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 260: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If the vehicle is towed by other means or incorrectly, vehicle damage may occur.
Page 261: Customer Assistance
Relationship Center at 1-800-521-4140. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 262 If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 263 Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the...
Page 264 THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford...
Page 265 • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s).
Page 266 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 267 4,600 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your dealer for complete...
Page 268 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 269: Reporting Safety Defects (U.s. Only)
Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. REPORTING SAFETY DEFECTS (U.S. ONLY)
Page 270: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 271 Cleaning • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish.
Page 272 Cleaning • 3.0L DOHC V6 engine • 3.9L-4V V8 engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer.
Page 273 Cleaning • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause.
Page 274 Cleaning • Do not use household or glass cleaners as these may damage the finish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: • Remove dust and loose dirt with a vacuum cleaner. •...
Page 275 FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 276 Cleaning Motorcraft Vinyl Cleaner (Canada only) (CXC-93) Motorcraft Vinyl Conditioner (Canada only) (CXC-94) Motorcraft Wheel and Tire Cleaner (ZC-37–A) 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 277: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 278: Engine Compartment
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located at the bottom left of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood by pushing upward on the handle.
Page 279 Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter. 2005 Lincoln LS (dew)
Page 280: Engine Oil
Maintenance and Specifications State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.
Page 281 Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, or between the lower and upper holes (depending on application), the oil level is acceptable.
Page 282 Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises of knock may be experienced.
Page 283: Battery
Maintenance and Specifications It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which is located in the luggage compartment, next to the spare tire.
Page 284 Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 285: Engine Coolant
Maintenance and Specifications If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal.
Page 286 If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant (yellow-colored), VC-7–A (U.S., except CA, OR and NM), VC-7–B (CA, OR and NM), meeting Ford Specification WSS-M97B51–A1. 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt)
Page 287 • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, VC-2 and VC-3 (US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection.
Page 288 Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.
Page 289 Maintenance and Specifications Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Page 290 Maintenance and Specifications How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the H (hot) area. • The symbol will illuminate. • The symbol will illuminate. • The symbol will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
Page 291 Maintenance and Specifications Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
Page 292 Maintenance and Specifications • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. •...
Page 293 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 294 Maintenance and Specifications If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Page 295 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 296 Maintenance and Specifications possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,000 miles (1,600 km) of driving (engine break-in period). You will get a more accurate measurement after 2,000 miles-3,000 miles (3,000 km–5,000 km).
Page 297 Maintenance and Specifications 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used.
Page 298 Maintenance and Specifications • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy.
Page 299 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 300 Maintenance and Specifications Please consult your Warranty Guide for complete emission warranty information. On board diagnostics (OBD-II) Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD-II). This OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 301 Maintenance and Specifications • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature.
Page 302 Maintenance and Specifications BRAKE FLUID RESERVOIR The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
Page 303: Air Filter(S)
Maintenance and Specifications Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Loosen the hose clamp on the outlet tube at the air filter housing. 2.
Page 304: Part Numbers
Maintenance and Specifications 5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unmetered air to enter the engine if not properly seated.
Page 305: Refill Capacities
Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used.
Page 306 Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. Refer to Lubricant Specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Add the coolant type originally equipped in your vehicle.
Page 307: Lubricant Specifications
Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake fluid Motorcraft High PM-1 ESA-M6C25-A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Door Silicone XL-6 ESR-M13P4-A weatherstrips Lubricant Door latch, hood Multi-Purpose...
Page 308 Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water.
Page 309 Maintenance and Specifications VEHICLE DIMENSIONS Vehicle dimensions Inches (mm) (1) Overall length 194.3 (4936) (2) Overall width 80.1 (2034) (3) Overall height 56.1 (1424) (4) Wheelbase 114.5 (2909) (5) Tread - Front 60.6 (1540) (5) Tread - Rear 60.7 (1543) 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA_English (fus)
Page 310 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
Page 311 Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) The vehicle identification number (VIN) contains the following information: 1.
Page 312 Maintenance and Specifications Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certification label. The following table tells you which transmission or transaxle each code represents. Code Description Five-speed automatic overdrive (5R55S) Five-speed automatic overdrive (5R55S) with Select Shift 2005 Lincoln LS (dew) Owners Guide (post-2002-fmt)
Page 313: Accessories
LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local authorized Lincoln or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 314 Accessories Scuff plates Speed control Lifestyle Bike racks Cargo organization and management Peace of mind Airbag anti-theft locks First aid and safety kits Full vehicle covers Engine block heaters Mobile-ease hands free communication system Remote start Vehicle security systems For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...
Page 315: Index
Index acid, treating emergencies ..283 jumping a disabled battery ..253 Accessory delay ......110 maintenance-free ....283 replacement, specifications ...304 AdvanceTrac ......231 servicing ........283 Air bag supplemental restraint BeltMinder .........171 system ......175, 179, 182 and child safety seats ....177 Brakes ........227 description ....175, 179, 182 anti-lock ......227–228 disposal ........186 anti-lock brake system (ABS)
Page 316 ....307–308 Emergency Flashers ....243 Cruise control (see Speed control) ....114 Emission control system ..299 Customer Assistance ....242 Engine ........308–309 Ford accessories for your cleaning ........271 vehicle ........275 coolant ........285 Ford Extended Service fail-safe coolant ......289 Plan ..........267 idle speed control ....283...
Page 317 Index specifications ....307–308 GAWR (Gross Axle Weight Rating) Exhaust fumes ......227 calculating .......222 GVWR (Gross Vehicle Weight Rating) calculating .......222 Fail safe coolant ......289 Floor mats .........137 Fluid capacities ......305 Hazard flashers ......243 Head restraints ....155, 160 Foglamps ........97 Headlamps ........96 Fuel ..........291 aiming ........98 calculating fuel...
Page 318 Index positioning .......202 select button ......125 warning messages ....130 storage ........202 Mirrors .......107, 110 Jump-starting your vehicle ..253 automatic dimming rearview mirror ........110 fold away .........114 Keyless entry system ....149 heated ........113 autolock ........147 programmable memory ..148 side view mirrors (power) ..113 Keys ...........139 positions of the ignition ..224 Moon roof ........120...
Page 319 Index fluid, checking and adding ..301 Select Shift Transmission fluid, refill capacity ....305 (SST) shifter ......237 fluid, specifications ..307–308 Servicing your vehicle ....277 Power Windows ......109 Setting the clock AM/FM/In-dash 6 CD ....19 AM/FM/Tape/CD .......23 Spark plugs, Radio ........17, 21 specifications .....304, 308–309 Rear Park Assist .......239 Specification chart,...
Page 320 Index Towing ........223 Vehicle Identification Number recreational towing ....223 (VIN) ..........311 trailer towing ......223 Vehicle loading ......216 wrecker ........260 Ventilating your vehicle ...227 Traction control ......230 Transmission ......234 brake-shift interlock (BSI) ..234 fluid, checking and adding Warning lights (see Lights) ..10 (automatic) ......302 fluid, refill capacities ....305 Washer fluid ......279...

Ford Lincoln LS 2005 Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Quick Links

Table of Contents

Related Manuals for Ford Lincoln LS 2005

Summary of Contents for Ford Lincoln LS 2005

Table of Contents