Page 1: Table Of Contents
Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo AM/FM stereo cassette AM/FM stereo with CD AM/FM stereo cassette with CD AM/FM stereo with cassette and in-dash six CD Climate Controls Manual heating and air conditioning Automatic temperature control Rear window defroster Lights Headlamps...
Page 2 Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Changing tires Lug Nut Torque Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Traction control Air suspension Transmission operation Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch...
Page 4: Introduction
State of California to cause cancer and birth defects or other reproductive harm. CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
Page 5 SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Page 6 • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent,...
Page 7 Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger air bag.
Page 8: Vehicle Symbol Glossary
Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Child Seat Tether Anchor Anti-Lock Brake System Powertrain Malfunction Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist...
Page 9 Vehicle Symbol Glossary Power Windows Front/Rear Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Check fuel cap 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) Introduction...
Page 10: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Page 12 Instrument Cluster Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately. Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system...
Page 13 Never remove the coolant reservoir cap while the engine is running or hot. Traction control AdvanceTrac active (if equipped): Illuminates when the Traction control system is active. It will be lit for a minimum of four seconds or for the duration of the Traction Control event, refer to the Driving chapter for more information.
Page 14 Instrument Cluster Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on. MESSAGE CENTER INDICATOR LIGHTS (IF EQUIPPED) Speed control: Illuminates when the speed control is activated.
Page 15: Gauges
Instrument Cluster Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened. GAUGES Standard instrument cluster gauges 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)
Page 16 Instrument Cluster Optional instrument cluster gauges Speedometer: Indicates the current vehicle speed. • Standard instrument cluster • Optional instrument cluster Engine coolant temperature gauge: • Standard instrument cluster 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) 60 70 0 0 0 0 0 0 0 km/h km/h TEMP...
Page 17 • Optional instrument cluster Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool, refer to What you should know about fail-safe...
Page 18 Instrument Cluster Trip odometer: Registers the miles (kilometers) of individual journeys. • Standard instrument cluster To reset, depress the control. • Optional instrument cluster Refer to Electronic Message Center in the Driver Controls chapter for Trip A and Trip B features. Battery voltage gauge (if equipped): Indicates the battery voltage when the ignition is in the...
Page 19 Engine oil pressure gauge (if equipped): Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed.
Page 20: Entertainment Systems
Entertainment Systems AM/FM STEREO (IF EQUIPPED) PUSH TONE 1. Seek: Press to find the next strong station down/up the frequency band. 2. Tune: Press to manually change radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. 4.
Page 21 Entertainment Systems 5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. Tone: Press TONE until the PUSH desired level — Bass, Treble, Fade TONE appears on the display. Turn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped).
Page 22: Am/Fm Stereo Cassette
Entertainment Systems AM/FM STEREO CASSETTE (IF EQUIPPED) 14 15 16 17 VOL - PUSH ON BASS TREB SEEK SCAN TUNE 1. Balance: Press to shift sound to the left/right speakers. 2. Fade: Press to shift sound to the rear/front speakers. 3.
Page 23 Entertainment Systems next selection). Then, press REW (for the beginning of the current selection) or FF (to advance to the next selection). The tape MUST have a blank section of at least four seconds duration between programs. 5. Side 1–2: Press to change tape SIDE 1 - 2 direction.
Page 24 Entertainment Systems 13. AM/FM: Press to choose a frequency band in radio mode. 14. Bass: Press decrease/increase the bass output. 15. Treble: Press decrease/increase the treble output. 16. EJ (Eject): Press to eject a tape. 17. Cassette door: Insert a cassette into the cassette door. 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)
Page 25: Am/Fm Stereo With Cd
AM/FM STEREO SINGLE CD PREMIUM AUDIO SYSTEM (IF EQUIPPED) 1. CD slot: Insert a CD, label side up. With the ignition on, the radio will begin play when a CD is inserted. If the ignition is off, press CD prior to inserting a disc. Do not force a disc into the system as damage could result.
Page 26 Entertainment Systems 5. Eject: Press to eject the CD. If the disc is not removed within the allotted time, the system will automatically reload the CD and begin play. Note: The eject function will work when the ignition is turned off. 6.
Page 27 Entertainment Systems When activated, AUTOSET will momentarily appear in the display when any of the preset controls are pressed. Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting.
Page 28: Am/Fm Stereo Cassette With Cd
Entertainment Systems 16. SCAN: Press SCAN to hear a brief sampling of radio stations or CD tracks. Press again to stop. PREMIUM/AUDIOPHILE SATELLITE COMPATIBLE AM/FM STEREO SINGLE CD/CASSETTE SYSTEM (IF EQUIPPED) 1. CD slot: Insert a CD, label side up. With the ignition on, the radio will begin to play a CD once inserted.
Page 29 3. BASS: Press BASS; then press SEL-TEXT decrease/increase the level of bass output. TREB (Treble): Press TREB; then press SEL-TEXT decrease/increase the level of treble output. 4. BAL (Balance): Press BAL; then press SEL-TEXT to shift sound to the left/right speakers. FADE: Press FADE;...
Page 30 Entertainment Systems stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40.
Page 31 Dolby: Works in tape mode to reduces tape noise and hiss. Press MENU until DOLBY XX appears in the display. Press toggle ON/OFF. The Dolby noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation.
Page 32 Entertainment Systems 13. SCAN: Press SCAN to hear a brief sampling of radio stations, selections or CD tracks. Press again to stop. 14. SHUF (Shuffle): Press to play the tracks on the current CD in random order. Press again to stop. 15.
Page 33: Am/Fm Stereo With Cassette And In-Dash Six Cd
Entertainment Systems AUDIOPHILE AM/FM STEREO IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED) 1. CD slot: To insert a CD, press LOAD. When the system is ready, insert a CD, label side up. 2. SEEK: Press to access the next/previous radio station or CD track.
Page 34 Entertainment Systems 4. MUTE: Press to mute the playing media. Press again to return to the playing media or turn the volume control to adjust the volume. 5. Eject: Press to eject CD(s) when the ignition is on or off. Numbers will illuminate in the display indicating which CD slots are loaded with CDs.
Page 35 Entertainment Systems 9. MENU: Press MENU repeatedly to access RDS on/off. SEL-TEXT to toggle RDS on/off. Press MENU again to access Program type mode or Show Type mode. (MENU must be pressed within 10 seconds to proceed to the next RDS mode.) The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RDS technology to transmit information.
Page 36 Entertainment Systems Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting. Press MENU to access and use SEL-TEXT to adjust the volume setting.
Page 37 RADIO FREQUENCIES AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors that can affect radio reception: •...
Page 38 (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 39: Climate Controls
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
Page 40: Automatic Temperature Control
Climate Controls To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
Page 41 3. Fan speed: Turn to manually increase or decrease fan speed. 4. Defrost: Distributes outside air through the windshield defroster vents and the side window demisters. 5. Floor/defrost: Distributes outside air through the windshield defroster vents, floor vents and the side window demisters. 6.
Page 42: Rear Window Defroster
Climate Controls • Remove any snow, ice or leaves from the air intake area at the base of the windshield. To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3.
Page 43: Lights
HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 44 Lights Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Page 45: Turn Signal Control
Domelamp Control The panel dimmer control also controls the domelamp operation. • Rotate the thumbwheel fully to the right, past detent to activate the domelamp. • In order to turn off the domelamp, rotate the thumbwheel to the left. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.
Page 46: Bulb Replacement
Lights With overhead console With overhead console and moon roof To turn on the map lamps, press the map lamp control. REAR COURTESY/READING LAMPS Rotate the lens to illuminate the lamp. With the lens in the flat position, the courtesy lamp lights when: •...
Page 47 Replacing exterior bulbs Check the operation of all the bulbs frequently. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility.
Page 48 Lights 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
Page 49 Lights 5. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front parking lamp/turn signal bulbs The park/turn lamp bulbs can be replaced without removing the headlamp assembly.
Page 50 Lights 1. Make sure headlamp switch is in OFF position, then open the trunk and remove plastic retainer to expose the lamp assembly hardware. 2. Carefully pull the carpet away to expose the plastic retainer. 3. Remove three nut and washer assemblies and the lamp assembly from the vehicle.
Page 51 Lights Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws, grommets and the license plate lamp assembly from the trunk lid. 2. Carefully pull the bulb from the socket and push in the new bulb. 3.
Page 52 Lights 3. Carefully pull the bulb socket out of the lamp assembly. 4. Pull the bulb straight out of the socket and push in the new bulb. To install, reverse the removal procedure. Overhead console lamps To remove and replace the lamps in the overhead console: 1.
Page 53: Driver Controls
MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
Page 54: Steering Wheel Adjustment
Driver Controls Poor wiper quality can sometimes be improved by cleaning the wiper blades, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.
Page 55 Slide on rod feature (if equipped) Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield. OVERHEAD CONSOLE WITHOUT MOON ROOF (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.
Page 56 Driver Controls 3. Press and hold the MODE control until VAR appears in the display, then release. The display should show the current zone number. 4. Press the MODE control until the desired zone number appears. The display will flash and then return to normal operation.
Page 57 Driver Controls 3. From a blank display press and release the MODE button once. The directional heading will be displayed. Note: If the compass is de-calibrated, CAL will be displayed in the right corner of the display. Refer to “Calibration mode” in this section for more details.
Page 58 Driver Controls 4. Determine which magnetic zone you are in by referring to the zone map. 5. Repeatedly press and release the RESET button to scroll through the zones 1–15 until the desired zone is displayed. 6. Press the MODE button to save the new zone setting and return to the compass normal mode.
Page 59 Driver Controls 4. Press the RESET button to de-calibrate the compass. The display will read CIRCLE SLOWLY TO CALIBRATE for a few seconds and then display a direction with CAL displayed on the right side. 5. Drive the vehicle in a tight circle in a magnetically clean area such as an open parking lot.
Page 60 Driver Controls Programming Do not program the HomeLink with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of the HomeLink . It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal.
Page 61 3. Simultaneously press and hold both the HomeLink and hand-held transmitter button. The message CHANNEL “X” (1,2 or 3) TRAINING will appear on the display. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming”...
Page 62 Driver Controls If the indicator light(s) underneath the house icon blink rapidly for two seconds and then turn to a continuous light, proceed with steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn”...
Page 63 Operating the HomeLink Wireless Control System To operate, simply press and release the appropriate HomeLink button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time.
Page 64 Driver Controls 1. Press and hold the desired HomeLink button. DO NOT release the button. The display will read CHANNEL “X” (1,2 or 3) TRANSMIT 2. The display will change to CHANNEL “X” (1,2, or 3) TRAINING after 20 seconds. Without releasing the HomeLink button, follow step 2 in the “Programming”...
Page 65: Power Windows
POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Page 66: Mirrors
Driver Controls POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.
Page 67: Speed Control
(darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up.
Page 68 Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release 2. Accelerate to the desired speed. 3. Press the SET + control and release it.
Page 69 Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed:...
Page 70 Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previously set speed.
Page 71 In any mode: • Press VOL + or - to adjust the volume. Climate control features • Press TEMP + or - to adjust temperature. MOON ROOF (IF EQUIPPED) To open the moon roof: • Press and hold the control forward to raise the moon roof to the vent position (when the glass panel is closed).
Page 72 Driver Controls Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening.
Page 73 Driver Controls 1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1 to program additional hand-held transmitters to the remaining two HomeLink buttons. This will erase previously programmed hand-held transmitter signals into HomeLink .
Page 74 Driver Controls 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink button.
Page 75 Operating the HomeLink Wireless Control System To operate, simply press and release the appropriate HomeLink button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time.
Page 76: Message Center
Driver Controls ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you to: • see problems such as door ajar, air suspension, trunk ajar, washer fluid low •...
Page 77 Press this control to switch the electronic instrument cluster display and the message center display from metric to English units. Select Each press of the SELECT control will select a different function. • Press the right side of the control to advance the function to the right.
Page 78 Driver Controls Message center functions DISTANCE TO EMPTY (DTE) This function estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will flash for 5 seconds and sound a tone for 1 second when you have approximately: •...
Page 79 • variations in top-off procedure from one fill-up to another • rounding of the displayed values to the nearest 0.1 gallons (liter) Press the RESET control while AVG ECON is displayed to reset the function. The average displayed is the average since the last reset.
Page 80 Driver Controls INTERIOR TRUNK CONTROL The remote trunk release control is located on the driver’s door trim panel and can be operated at any time. You can render the switch inoperable by locking the button with your master key. CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs.
Page 81 Driver Controls POSITIVE RETENTION FLOOR MAT Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 82: Locks And Security
Locks and Security KEYS The vehicle is equipped with a master (black) key and valet (gray) key lock system. The master key will access doors, trunk, glove box, ignition and remote trunk release. The valet key will access doors and ignition only.
Page 83 Locks and Security Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 84 Locks and Security Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.
Page 85 The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features operate with the ignition in any position, except in the 3 (ON) , with the transmission not in either P (Park) or N (Neutral).
Page 86 Locks and Security 3. Cycle the ignition from the 4 (ON) to the 3 (OFF) position. 4. Press the power door unlock control three times. 5. Turn the ignition to the 4 (ON) position. The doors will lock and unlock. 6.
Page 87 Locks and Security To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.
Page 88 Locks and Security • Perform the following programming procedure yourself: Place the key in the ignition and cycle from 1 (OFF/LOCK) to 3 (ON) eight times in rapid succession within 10 seconds. After doors lock/unlock, press any control on all transmitters (up to four).
Page 89 Locks and Security Autolock (if equipped) This feature automatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (ON) position, • the brake pedal is depressed, • you shift into any gear. Relock The autolock feature repeats when: •...
Page 90: Anti-Theft System
Locks and Security KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you 7 8 9 0 can: • lock or unlock the vehicle doors without using the key. • open the trunk. See also Remote entry system in this chapter for more information. Your vehicle has a factory-set 5–digit code that operates the keyless entry system.
Page 91 3. Enter a second personal 5-digit code. Each number must be entered within five seconds of each other. 4. Press 3 • 4 to store the second personal code. 5. The doors will again lock then unlock to confirm programming of the new code.
Page 92 Note: The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues.
Page 93 • When the ignition is in the 3 (ON) position, the indicator will glow for 3 seconds to indicate normal system functionality. If a problem occurs with the SecuriLock rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for service.
Page 94 Locks and Security will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your dealership to have the spare coded key(s) programmed.
Page 95: Seating And Safety Restraints
Seating and Safety Restraints SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 96 Seating and Safety Restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the manual recline function (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 97 Seating and Safety Restraints To adjust the front seatback using the manual recliner: • Lift and hold the handle located on the side of the seat. • Lean against the seatback to adjust it to your desired position. You can recline the seat back or bring it forward.
Page 98 Seating and Safety Restraints Adjusting the power front seats – door mounted controls (if equipped) The controls for the power seats are located on the inside of each front door. Never adjust the driver’s seat or seatback when the vehicle is moving.
Page 99 Seating and Safety Restraints Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)
Page 100: Safety Restraints
Seating and Safety Restraints Seat mounted cup holders and armrest storage compartment (if equipped) Your vehicle is equipped with cup holders in the rear seat armrest. To access the cup holders, rotate armrest into use position. Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Page 101 Seating and Safety Restraints How does the Personal Safety System work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM).
Page 102 Seating and Safety Restraints in rear-facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by seat belts or child safety seats and they move forward during pre-crash braking.
Page 103 Seating and Safety Restraints of the safety belts and helps properly position the occupant relative to the airbag to improve protection. The safety belt pretensioners can be either activated alone or, if the collision is of sufficient severity, together with the airbags. Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled...
Page 104 Seating and Safety Restraints To reduce the risk of injury, make sure children sit in the back seat where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Page 105 Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 106 Seating and Safety Restraints Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and prevents more belt from being pulled out if the belt is pulled out too quickly. The belt will unlock when you stop pulling on it. Automatic locking mode In this mode, the shoulder belt is pre-locked.
Page 107 This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision to verify that the automatic locking retractor feature for child seats is still working properly.
Page 108 Seating and Safety Restraints Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Lap belts Adjusting the front center seat lap belt The lap belt should fit snugly and as low as possible around the...
Page 109 Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON...
Page 110 Seating and Safety Restraints If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph...
Page 111 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work”...
Page 112 Seating and Safety Restraints Reasons given... “I have an airbag” “I’d rather be thrown clear” Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the BeltMinder feature please follow the directions stated below.
Page 113 Seating and Safety Restraints • The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.
Page 114: Airbags
(if equipped), shoulder belt guide on seatback (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced.
Page 115 Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Ford Motor Company recommends that a certified technician inspect all steering column assemblies in use in vehicles involved in a collision.
Page 116 Seating and Safety Restraints Do not attempt to service, repair, or modify the steering column, its adaptive module, or its fuses. See your Ford or Lincoln/Mercury dealer. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably.
Page 117 Seating and Safety Restraints Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
Page 118 Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 119 Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 120 Seating and Safety Restraints Even with the front passenger sensing system, children 12 and under should be properly restrained in the back seat. When the front passenger seat is occupied and the sensing system has turned off the passenger’s frontal airbag, the passenger airbag off or pass airbag off indicator will light and stay lit to remind you that the front passenger frontal airbag is off.
Page 121 If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide.
Page 122 Seating and Safety Restraints Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 123 Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
Page 124 Seating and Safety Restraints The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side airbags are designed to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration.
Page 125: Child Restraints
Seating and Safety Restraints Disposal of airbags and airbag equipped vehicles (including pretensioners) See your local dealership or qualified technician. Airbags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
Page 126 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 127 Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top...
Page 128 Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child.
Page 129 80 lb. (36 kg) using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LATCH and tether anchors.
Page 130 Seating and Safety Restraints 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat...
Page 131 Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it.
Page 132 Seating and Safety Restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
Page 133 Seating and Safety Restraints 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Page 134 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat.
Page 135 Seating and Safety Restraints If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Page 136: Tires, Wheels And Loading
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 137 The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 138 (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company. Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and...
Page 139 (if equipped), at least monthly and before long trips. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial type tire pressure gauge rather than a stick type tire pressure gauge.
Page 140 Tires, Wheels and Loading inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label. When weather temperature changes occur, tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
Page 141: Changing Tires
Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 142 Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 143 • Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs •...
Page 144 Tires, Wheels and Loading 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. 3. Remove the spare tire and the jack.
Page 145 4. Remove the lug wrench from the jack. Rotate the lug wrench socket out from the handle. 5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle.
Page 146 Tires, Wheels and Loading • Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. To lessen risk of personal injury, do not put any part of your body under the vehicle while changing a tire.
Page 147: Lug Nut Torque
20 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel.
Page 148 Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1.
Page 149 Note: You may not find this information on all tires because it is not required by federal law. Letter rating Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR.
Page 150 Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 course as a tire graded 100.
Page 151 Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks.
Page 152 Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 153 Tires, Wheels and Loading TIRE CARE Improper or inadequate vehicle maintenance can also cause tires to wear abnormally. Here are some of the important maintenance items: Tire wear Measure and inspect the tire tread on all your tires periodically. Advanced and unusual tire wear can reduce the ability of tread to grip the road in adverse (wet, snowy, etc.) conditions.
Page 154 If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have a qualified technician at a Ford or Lincoln Mercury dealer check the wheel alignment periodically.
Page 155 The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance and longer tire life.
Page 156 Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 157: Vehicle Loading
Follow these guidelines when using snow tires and chains: • Either cable type chains or SAE class S chains can be used. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. •...
Page 158 Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Safety Compliance Certification Label on the B-Pillar or the edge of the driver’s door.
Page 159 Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)
Page 160 Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door.
Page 161 GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.
Page 162 Tires, Wheels and Loading mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your dealership (or the RV and Trailer Towing Guide provided by your dealership) for more detailed information.
Page 163: Trailer Towing
capacity to carry you, 4 of your friends and all the golf bags? You and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) –...
Page 164 Tires, Wheels and Loading Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. The GCW of your vehicle and trailer should not exceed 6,600 lb. (2,993 kg).
Page 165 Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow When towing a trailer: •...
Page 166: Recreational Towing
• Maximum distance is 50 miles (80 km) If a distance of 50 miles (80 km) or a speed of 35 mph (56 km/h) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.
Page 167: Driving
STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational.
Page 168 Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
Page 169 5. Turn the key to 3 (ON) without turning the key to 4 (START). CHECK FUEL SUSP CHECK FUEL ENGINE VOLTS FUEL < FUEL FILL DOOR CHECK ENGINE CHECK FUEL – Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced.
Page 170 Driving Starting the engine 1. Turn the key to 3 (ON) without turning the key to 4 (START). 2. Turn the key to 4 (START), then release the key as soon as the engine starts. Excessive cranking could damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again.
Page 171: Brakes
BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance information for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 172 Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Page 173 Parking brake with auto-release (if equipped) Apply the parking brake whenever the vehicle is parked. To set the parking brake: 1. Move the gearshift to P (Park). 2. Push pedal downward. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released.
Page 174: Traction Control
Driving If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the lever to manually release the parking brake. TRACTION CONTROL (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control system.
Page 175 Do not attempt to service, repair, or modify the steering column, its adaptive module, or its fuses. See your Ford or Lincoln Mercury dealer. To prevent damage to the power steering system, never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running.
Page 176: Air Suspension
Driving It is also important to maintain a proper power steering fluid level in the power steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). •...
Page 177: Transmission Operation
This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk.
Page 178 Driving 2. Locate the access plug on the underside of the steering column cover. 3. Remove the access plug using a flat head screwdriver. Insert the screwdriver into the access hole nearest the steering wheel. Then push and hold the override button using a flat head screwdriver. Apply the brake pedal and shift the transmission into N (Neutral) while continuing to depress the override button.
Page 179 2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral). When the key is in the ignition and in the ACC position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed.
Page 180 Driving • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Page 181 If your vehicle is equipped with a floor-shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift handle. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. • Standard instrument cluster • Optional instrument cluster Drive (not shown) Drive is activated when the transmission control switch is pressed.
Page 182 Driving 2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to (Overdrive), move the gearshift lever into the (Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed.
Page 183 Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine.
Page 184: Roadside Emergencies
50,000 miles (80,000 km) on Lincoln vehicles. Roadside assistance will cover: • a flat tire change with a good spare (except Ford GT which has a tire inflation kit) • battery jump start • lock-out assistance (key replacement cost is the customer’s responsibility) •...
Page 185: Hazard Flasher Switch
Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140.
Page 186: Fuses And Relays
Roadside Emergencies The fuel pump shut-off switch is located on the left side of the trunk behind the left rear tail light and the trunk liner. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2.
Page 187: Passenger Compartment Fuse Panel
Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse Mini Standard rating fuses fuses...
Page 188 Roadside Emergencies The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) Relay Passenger Compartment Fuse Panel Description Taxi, Cluster, Lighting Control Module (Interior Lighting) Ignition (ON) - Electronic Automatic Temperature Control (EATC) module, A/C mode switch (vehicles equipped with EATC only)
Page 189 Fuse/Relay Fuse Amp Location Rating 7.5A 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies Passenger Compartment Fuse Panel Description Ignition (ON) - Cluster LCM (Park lamps, Switch illumination) Ignition (ON) - Rear Air Suspension Module (RASM), Variable Assist POwer Steering (VAPS) LCM (Headlamps, Cornering lamps)
Page 190 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating Relay 1 Full ISO relay 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) Passenger Compartment Fuse Panel Description Left-hand low beam, DRL Ignition (ON/ACC) - Back-up lamps Right-hand low beam, DRL Ignition (ON/ACC) - Restraint Control Module (RCM), Occupant Classification Sensor (OCS), Passenger Air bag Deactivation...
Page 191 Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 192 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 20A* 25A* 10A* 20A* 10A* 15A* 30A* 20A* 15A* 20A* 15A* 25A* 20A* 20A* 20A* 20A* — — 15A* 15A* 15A* — — 40A** 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description Ignition switch (Key in, RUN 1,...
Page 193 Fuse/Relay Fuse Amp Location Rating 50A** 50A** 40A** 30A** 40A** 40A** 20A** 20A** 30A** 50A** 30A** 40A** 50A** 50A** 50A** 50A** 50A** 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies Power Distribution Box Description Cooling fan Instrument panel (I/P) fuse box feed #1, I/P fuses 23, 25, 27 and 31 Instrument panel (I/P) fuse box feed #2, I/P fuses 1, 3, 5, 7 and 9...
Page 194 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 50A** ⁄ ISO relay — ⁄ ISO relay ⁄ ISO relay — ⁄ ISO relay — — ⁄ ISO relay Full ISO relay Full ISO relay Full ISO relay Full ISO relay Diode Diode Diode 20A Circuit...
Page 195: Jump Starting
Relays Relays are located in the power distribution box and should be replaced by qualified technicians. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Page 196 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 197 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 198 Roadside Emergencies 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.
Page 199 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 200: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Before your vehicle can be towed, the air suspension control in the luggage compartment must be turned to the OFF position (if equipped).
Page 201: Customer Assistance
Center at 1-800-392-3673 (FORD). Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 202 If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 203 Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the...
Page 204 THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford...
Page 205 • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s).
Page 206 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 207 4,600 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this 2005 Crown Victoria (cro)
Page 208 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 209: Reporting Safety Defects (U.s. Only)
Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. REPORTING SAFETY DEFECTS (U.S. ONLY)
Page 210: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 211 • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish.
Page 212 Cleaning • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer.
Page 213 • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly.
Page 214 FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they...
Page 215 Cleaning vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Car Care Kit (ZC-26) Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S.
Page 216: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 217: Engine Compartment
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3.
Page 218: Engine Oil
In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 219 Maintenance and Specifications 2. Turn the engine off and wait up to 10 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5.
Page 220 Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician.
Page 221: Engine Oil And Filter Recommendations
Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 222: Battery
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to scheduled maintenance information for the service interval schedules.
Page 223 Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 224: Engine Coolant
Maintenance and Specifications • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in scheduled maintenance information.
Page 225 Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Page 226 • Add Motorcraft Premium Gold Engine Coolant (yellow-colored), VC-7–A (U.S., except CA, OR and NM), VC-7–B (CA, OR and NM), meeting Ford Specification WSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan.
Page 227 Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.
Page 228 Maintenance and Specifications Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this section.
Page 229 Maintenance and Specifications What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
Page 230: Fuel Information
Maintenance and Specifications • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage.
Page 231 Maintenance and Specifications If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Page 232 Maintenance and Specifications splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling.
Page 233 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 234 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 235 Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. •...
Page 236 Maintenance and Specifications For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Page 237 Maintenance and Specifications Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel.
Page 238 The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting 2005 Crown Victoria (cro)
Page 239 Maintenance and Specifications emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Page 240 Maintenance and Specifications These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the Check engine/Service engine soon light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
Page 241 Maintenance and Specifications 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range.
Page 242 Maintenance and Specifications weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature. 2.
Page 243 Maintenance and Specifications The transmission fluid should be in this range if at normal operating temperature (150°F-170°F [66°C-77°C]). The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe range may result in transmission failure.
Page 244: Air Filter(S)
Maintenance and Specifications If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
Page 245: Part Numbers
Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used.
Page 246: Refill Capacities
Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. Refer to Lubricant Specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Ensure the correct automatic transmission fluid is used. MERCON and MERCON V are not interchangeable.
Page 247: Lubricant Specifications
9/16 inch (6 mm to 14 mm) below the bottom of the filler hole. Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark.
Page 248 Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Add 4 oz. (118 ml) of Additive Friction Modifier XL–3 or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok rear axles.
Page 249 Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio VEHICLE DIMENSIONS (AT CURB MASS) Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear Denotes long wheel base 2005 Crown Victoria (cro)
Page 250: Certification Label
2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus) MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXXXXXXXXX FRONT GAWR: XXXXXX/XXXXXXX REAR GAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL...
Page 251 Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) The Vehicle Identification Number (VIN) contains the following information: 1.
Page 252 Maintenance and Specifications Transmission/Transaxle code designations You can find a transmission/transaxle code on the Safety Compliance Certification Label . The following table tells you which transmission or transaxle each code represents. Code Description Four-speed automatic overdrive (4R70E) - Livonia Four-speed automatic overdrive (4R70E) - Sharonville 2005 Crown Victoria (cro) Owners Guide (post-2002-fmt)
Page 253: Accessories
In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications. Ford Motor Company will repair or...
Page 254 Accessories Peace of mind First aid and safety kits Full vehicle covers Locking gas cap Remote start Vehicle security systems Mobile-Ease hands-free communication system For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...
Page 255: Index
ABS (see Brakes) ...171 Air cleaner filter ...244–245 Air conditioning ...40 Air suspension ...176 description ...176 Airbag supplemental restraint system ...114–115, 122 and child safety seats ...117 description ...115, 122 disposal ...125 driver airbag ...117, 123 indicator light ...122, 124 operation ...117, 123 passenger airbag ...117, 123 side airbag ...122...
Page 256 ...228, 246 specifications ...247, 249 Cruise control (see Speed control) ...67 Cupholder(s) ...100 Customer Assistance ...184 Ford accessories for your vehicle ...214 Ford Extended Service Plan ...207 Getting assistance outside the U.S. and Canada ...208 Getting roadside assistance ...184 Getting the service you need ...201...
Page 257 recommendations ...221 refill capacities ...246 specifications ...247, 249 Exhaust fumes ...170 Fail safe cooling ...229 Floor mats ...81 Fluid capacities ...246 Fuel ...230 calculating fuel economy ...59, 235 cap ...232 capacity ...246 choosing the right fuel ...233 comparisons with EPA fuel economy estimates ...238 detergent in fuel ...234 filling your vehicle with...
Page 258 Index Keyless entry system ...90 autolock ...89 keypad ...90 programming entry code ...90 Keys ...82, 93 positions of the ignition ...167 Lamps autolamp system ...43 bulb replacement specifications chart ...47 daytime running light ...43 headlamps ...43 headlamps, flash to pass ...44 instrument panel, dimming ...44 interior lamps ...45–47, 52 replacing bulbs ...46–47, 49, 51...
Page 259 Rear window defroster ...42 Relays ...186, 195 Remote entry system ...84 illuminated entry ...88 locking/unlocking doors ...85 opening the trunk ...86 replacement/additional transmitters ...87 Roadside assistance ...184 Safety Belt Maintenance ...114 Safety belts (see Safety restraints) ...100, 103, 105–107 Safety defects, reporting ...209 Safety restraints ...100, 103, 105–107 belt minder ...109...
Page 260 Index Towing ...163 recreational towing ...166 trailer towing ...163 wrecker ...200 Traction control ...174 Traction-lok rear axle ...182 Transmission ...177 brake-shift interlock (BSI) ...177–178 fluid, checking and adding (automatic) ...241 fluid, refill capacities ...246 lubricant specifications ..247, 249 Trunk ...83 remote release ...80, 86 Turn signal ...45 Vehicle dimensions ...249...

This manual is also suitable for:

2005 crown victoria 2006 crown victoria

Ford 2005 Grand Marquis Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Tires, Wheels and Loading

Driving

Roadside Emergencies

Customer Assistance

Cleaning

Maintenance and Specifications

Accessories

Index

Quick Links

Table of Contents

Related Manuals for Ford 2005 Grand Marquis

Summary of Contents for Ford 2005 Grand Marquis

This manual is also suitable for:

Table of Contents