Automatic Code Entry; Learning Commands - Harman Kardon DPR 1005 Owner's Manual

Programming the Remote
Although the DPR remote is preprogrammed
with an extensive library of codes for many major
brands, it is also possible that you may have
attempted to program a product that is too new
or too old, and thus not all of its commands will
be in the code library. You may fill in the codes
for any button that does not operate properly by
using the learning technique shown on page 47.

Automatic Code Entry

In addition to manual code selection using the
brand name list, it is also possible to automati-
cally search through all the codes that are stored
in the DPR remote's library to see whether a
device will respond even if it is not listed among
the brands that appear when you program the
remote manually. To automatically search
through the codes that are available for a specific
device type (e.g., DVD, VCR), follow these steps:
1. Turn on the power to the device you wish to
program into the DPR remote. This is impor-
tant, as in a later step you will need to see
whether the device turns off to determine
whether the remote has been programmed for
the proper remote codes.
2. Press and hold the Program Button
about three seconds while the message shown
in Figure 15 appears in the remote's LCD
Information Display . Release the but-
ton when the red light under the Set Button
appears.
3. The remote's message (Figure
MAIN MENU
16) will appear in the LCD display and the Set
Button will remain illuminated in red.
Press the Set Button to begin the
process of selecting a device and locating the
proper remote codes.
4. will appear in the
SELECT A DEVICE
LCD display (Figure 17).
Press the Navigation Buttons
scroll through the list of device categories and
press the Set Button when the device
for which you wish to set the codes appears.
For this example, we will select "TV" to enter
the codes needed to operate your TV.
5. At the next menu screen on the remote (Figure
18), press the Navigation Buttons
so that the bottom line of the LCD display
reads (Figure 22) and then press the
AUTO
Set Button to enter the Automatic pro-
gramming mode.
P R O G R A M D E V I C E
A U T O
Figure 22
6. As instructed on the next menu screen, press
the Navigation Buttons
automatic code search process. Your confirma-
tion that the remote is sending out commands
is the movement of a square block across the
top line of the LCD display screen while the
bottom line reads
PLEASE WAIT...
also see the transmit icon in the upper right
corner of the LCD display's top line to remind
you that the remote is working even though
you may not see anything happening to the
device being programmed.
7. It will take a few seconds for the remote to
send out the first group of commands, after
which you will see a new display in the LCD
screen, as shown in Figure 23. Following the
instructions, if the device being programmed
has NOT turned off, press the
Buttons again to send another group of
codes. If the device being programmed has
turned off, skip to Step 9.
P O W E R O F F ?
Y -
1 ~ 0 N -
Figure 23
8. By pressing the
again, the remote will send out a new set of
commands. When it pauses, follow the instruc-
tions shown in Step 7. Depending on how
many codes are stored for a specific device
type, you may have to repeat this process as
many as fifteen times. Remember, if the device
turns off, skip to Step 9. When all the codes for
the device being programmed have been tried,
for
the instruction shown in Figure 24 will appear.
This means that the codes for the product you
are trying to program are not in the DPR
remote library and you will have to "learn"
them into the remote following the
instructions shown on page 47. Press the
Set Button
programming process.
R E A C H E N D P O I N T
E X I T - > S E T K E Y
Figure 24
9. If the device being programmed does turn off
after following the instructions in Step 7, you
to
will need to verify the code set by pressing the
Numeric Keys
in Figure 23. Point the remote at the device
being programmed, and press the "1" Button
to see whether the device turns back on.
10. After pressing and releasing the "1" Button
, check to see whether the device has
turned back on. If it has, skip to Step 12. If it
does not turn on, press the "2" Button
or the next button in the numeric sequence
if you are repeating the procedure, as
instructed by the LCD screen in Figure 25.
P O W E R O N ?
Y - S E T N -
Figure 25
to begin the
. You will
11. When pressing the "1" button does not turn
Navigation
12. When pressing one of the numeric keys in
Navigation Buttons
13. When the codes are saved, the remote will
as instructed to exit the

Learning Commands

On occasions when the DPR remote does not
contain the codes for a particular product's
remote in its built-in library, or when you wish to
program a missing or special function into one
button of a device, the DPR remote's learning
capability allows you to do that. To teach com-
mands from one product's remote into the DPR
remote, follow these steps:
in sequence, as instructed
The process requires that both the device's origi-
nal remote and the DPR remote be available.
Before pressing any buttons on either remote,
place them so that the IR transmitter on the
remote from the device to be programmed is
facing the Infrared Lens
remote. The two remotes should be no more than
,
an inch apart, and there should not be any direct
sunlight or other bright light source near the
remotes.
1. Press and hold the Program Button
1 ~ 0
2. The remote's
the device being programmed back on,
repeat the procedure by trying the remainder
of the Numeric Keys in sequence, each
time pressing and then releasing the button
to see whether the new device turns back on.
When it does, skip to the next step. However,
if you try all 10 numeric keys and find that
the unit will not turn on, you won't be able
to use this method to program the device.
Press the Clear Button to exit the
programming process. You'll need to follow
the Learning Commands instructions below
to enter the codes for this device into the
DPR remote.
Step 10 or 11 causes the device being
programmed to turn back on, follow the
instructions shown in Figure 22 and press the
Set Button within five seconds of the
device turning on. After you press the Set
button, the top line of the LCD display will
read and then the word
SAVING...
will flash four times in the center of the
bottom line.
return to normal operation, and whenever
you press the Input Selector Button
that was just programmed, the codes for the
new device will be used. If no further buttons
are pressed, the remote will revert back to
the default setting for DPR commands.
on the DPR's
about three seconds while the message shown
in Figure 15 appears in the remote's LCD
Information Display . Release the
button when the red light under the Set
Button appears.
message (Figure
MAIN MENU
16), will appear in the LCD display and the
Set Button will remain illuminated in
red. Press the Navigation Buttons
once so that Learn appears on the bottom line
PROGRAMMING THE REMOTE 47
SAVED
for