HYDRO-HEATER Sanitizing Sink Heaters Food Rethermalizers/Bain-Marie Heaters Operating Manual This manual contains important safety information concerning the maintenance, use, and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor.
Hydro- Heater in the spaces below. Please have this information available when calling Hatco for service assistance. Model No. ____________________________________ Serial No. ____________________________________...
IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. WARNINGS Hatco 3CS2 and FR2 series units are designed for commercial use only by properly trained personnel! To avoid any injury or damage to the unit read and follow the instructions contained in this manual.
Page 4
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. CAUTIONS Do not overtighten unions or nuts. Overtightening may cause leaks. Do not turn the electrical current to the unit on until the holding vessel has been filled with water or element burnout may occur.
3CS2 MODELS The Hatco 3CS2 model heaters are designed for use with any manual dishwashing operation. The 3CS2 heater maintains sanitizing rinse water of 180ºF (82ºC) by using a special electronic temperature controller and “free flow”...
Hatco does not supply the vessel that contains the water, nor the system which determines how food is placed and held in the vessel. The Hatco FR2 unit attaches to the bottom of the vessel and supplies hot water to the vessel.
Install a fused disconnect switch or circuit breaker sized according to the applicable Electrical Rating Chart. The wiring from the switch or circuit breaker to the Hatco unit must be in accordance with local electrical requirements and codes For proper electrical installation conforming to local electrical codes consult a licensed electrical contractor.
PLUMBING An adhesive backed paper template is shipped with the unit and is used to locate the sink strainer holes. Use the following procedure to install the heater unit to the holding vessel. NOTE: The FR2 heater should be positioned with no more than 3' (914 mm) on either side when mounted under holding vessel.
Page 10
INSTALLATION CAUTION Do not overtighten unions or nuts. Overtightening may cause leaks. NOTE: A 3/4" (19 mm) hose or pipe may be connected to the heater sump drain and run to an open sight drain. The sump drain should not be permanently connected to the sanitary drain system.
START-UP PROCEDURES WARNINGS Hatco 3CS2 and FR2 series units are designed for commercial use only by properly trained personnel! To avoid any injury or damage to the unit read and follow the instructions contained in this manual. Do not operate this equipment unless you have read and completely understood the contents of this manual.
Page 12
NOTE: If unit displays “E1” or “E2” the internal water sensing probe is out of temperature range. If this occurs contact Hatco Parts and Service Team or an Authorized Service Agent in your area for assistance.
MAINTENANCE GENERAL WARNING To avoid any electrical shock hazard, or physical burns turn the power OFF at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. WARNING To prevent any injury or damage to the unit do not pull unit by power cord.
NOTE: Inlet strainer is the strainer closest to the front of the unit. 5. Attach power flush hose with adapter, Hatco part #05.06.010.00, to a fresh water supply and place into outlet (rear) strainer. Flush fresh water through heater unit until discharge from sump is clear.
MAINTENANCE DELIMING INSTRUCTIONS CAUTION Inspect daily for lime and sediment buildup inside unit. Excessive amounts can affect unit performance and reduce the operating life of the unit. NOTE: Product failure caused by liming or sediment buildup is not covered under warranty. CAUTION To avoid any damage to the heater unit use only delimers that are non-corrosive to aluminum, brass...
Page 17
Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure...
Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer’s sole expense.
NEW YORK GCS Service Acme American Repairs, Inc. Indianapolis 317-545-9655 Brooklyn Parts & Service Fax (800) 690-2966 Printed in U.S.A. November 2003 HATCO AUTHORIZED PARTS DISTRIBUTORS NEW YORK (continued) Alpro Service Co. 319-323-1823 Brooklyn Appliance Installation Buffalo Northern Parts Dist.