INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Device overview...
Page 3
MENU button - to activate the setup menu. Arrow buttons - to selection items and input data in lists and selection menus. Volume control - turn clockwise to increase the volume, anticlockwise to decrease the volume. OK button - to confirm menu entries and start the scan function in the various audio modes.
Page 4
TravelPilot. Union. You can view the guarantee condi- es provide incorrect or unoptimised navi- tions at www.blaupunkt.de or ask for them gation due to improper operation, changes The TravelPilot is a radio navigation sys- directly at: to the traffic flow regulation, construction tem the size of a standard car radio.
Overview of navigation functions N1 NAVI N1 ENTER N1 LIST LAST DESTN CITY CITY... BERLIN, UNT BERLIN ER DEN LIN Press the NAV button 7 once in order to button : to select the first Use the The selected place name is then displayed switch from the radio or CD-changer (op- letter of the required place in the text input in the list of destination places.
Page 6
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP FM 1 EUROPE FM 1 EUROPE N1 SELECT 07p16 CITY STREET T M C T M C B6/WESTSCH CENTRE NELLWEG SPEC DESTN In the following selection, choose between When you have finished entering the desti- The current audio source is displayed STREET, CENTRE or SPECial DESTinatioN.
Safety information The TravelPilot has been designed for use in passenger cars. Special information such as height restrictions or maximum permitted road load, which is required for navigating trucks and buses, is not included on the navigation CDs. Inserting / removing a CD •...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Device overview ....162 Navigation ......181 Radio mode ......205 How navigation works ....... 181 Convenient RDS functions (AF, REG) ..205 Overview of navigation Inserting the navigation CD ...... 181 Switching to radio mode ......
Page 9
CD changer mode ....215 Setup - basic settings ... 222 Calibrating the device ... 232 Switching to CD changer mode ....215 Setting the maximum power-on New installation .......... 232 volume - “ON VOLUME” ......223 Selecting CDs ..........216 Calibration after a tyre change ....
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Compatible navigation CD-ROMs The TravelPilot can only be used with navigation CD-ROMs that are labelled with a “DX”. If no CD-ROM is inserted in the unit, a message informing you of this appears in the display.
About these instructions The aim of these instructions is to familiarize you with the functions of the Travel- Pilot and ensure that you can safely and successfully operate the unit. Before starting to use your TravelPilot, please read these instructions carefully and keep them in a safe place in your vehicle.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Removable control panel Theft protection As a way of protecting your car radio against theft, the unit is equipped with a removable control panel (flip-release panel). Without this control panel, the car radio is worthless to a thief.
Attaching the control panel Slide the control panel straight into the device’s bracket. Close the control panel. Note: When attaching the control panel, make sure you do not press the display. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Switching the device on/off To switch your TravelPilot on, press button 3. The device plays the last active audio source at the volume level that was set when the unit was switched off. You can limit the power-on vol- ume to a maximum value.
Selecting the operating mode N1 NAVI To select navigation mode, LAST DESTN press the NAV button 7. BERLIN, UNT The navigation memory bank that you used last and the last destination ER DEN LIN in this memory bank are displayed. To select radio mode, press the FM•AM button 4.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Adjusting the volume To increase the system volume, turn the volume control 2 in a clockwise direction. To decrease the system volume, turn the volume control 2 in an anticlockwise direction. Whilst you are making your adjustments, the currently set value is dis- played in the top line of the display.
Page 17
Automatically putting through telephone calls If the device is suitably connected to a car telephone, the telephone call will be outputted over the TravelPilot’s loudspeakers. TELEPHONE appears in the top line of the display. You can set the volume level for telephone calls. For further information, read the section entitled “Setting the volume for telephones - TEL VOLUME”...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Display The TravelPilot’s display contains all the navigation information (e.g. visual driv- ing recommendations), menus and lists, as well as the radio, CD and CD chang- er (optional) audio sources. The display’s brightness and readability can be optimised to suit the viewing angle in your vehicle.
Switching on a coded device after disconnection from the battery power supply If you switch on a coded unit after having disconnected it from the battery power supply (for instance, after having carried out a repair to the vehicle), a message will appear requesting that you enter the code.
Page 20
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Entering the wrong code number If you inadvertently entered and confirmed the wrong code, you can enter it again. To prevent thieves from working out the numerical code by trial and error, the unit will be locked for one hour if the code is entered incorrectly three times.
Navigation The TravelPilot’s navigation system helps you find your way to destinations quickly and safely without first having to spend time studying a roadmap. When naviga- tion is active, you will be guided by the device’s voice output feature. The sys- tem will warn you in good time about approaching turning-off points.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Note: The process of loading the software from the navigation CD N1 NAVI must not be interrupted. LAST DESTN Starting navigation BERLIN, UNT Press the NAV button 7 whilst the unit is switched on. ER DEN LIN The last destination in the current navigation memory bank is displayed for seven seconds.
After navigation is activated using the NAV button 7, the last destination of the N1 NAVI current memory bank is displayed for seven seconds. After the seven seconds have elapsed or after the ESC button 8 has been pressed, a menu for select- LAST DESTN ing the destination type (CITY or SPECial DESTinatioN) is displayed.
Page 24
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Example: If you are entering a street name and there are no streets N1 ENTER beginning with the letter A in the destination town, the letter A will not be displayed. Similarly, the letter C will not be displayed if you CITY entered B as the first letter and there are no streets in the destina- tion town with the BC letter combination.
Page 25
If you want to accept the name, press the OK button ;. N1 ENTER The entered name is displayed in the list of place names (if entering a place) or street names (if entering a street). CITY BERLIN Deleting letters To delete an incorrect letter that you entered accidentally, button :.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Entering a destination - place N1 SELECT If you want to drive to a destination in a place, you first have to specify a place name. DESTN TYPE... Select the CITY menu item in the navigation menu. CITY The text input line for entering the place name appears (for further infor- SPEC DESTN...
Note: A requirement is that the appropriate data are available on the N1 ENTER navigation CD. If data are not available for certain items, they will not be displayed. STREET UNTER DEN Entering a destination - street, intersection and house number LINDEN Select the STREET menu item.
Page 28
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Note: A requirement is that the appropriate data are available on your navigation CD. If data are not available for certain items, they will not be displayed as options. Entering a destination - intersection N1 ...
You can now start navigation using the OK button ;. Plus Point: After you have finished entering the destination and before starting navigation, you have the option of storing the destination in the destination memory. For further information, read the section entitled “Destination memory”.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Special destinations Special destinations that can be used when entering a destination are combined in categories. Some special destinations (see the list below) are available na- tionally and others are only available in the surrounding area of your destination or current position.
Page 31
– Petrol station, in the destination surrounding area / current position – Culture/arts, in the destination surrounding area / current position – Car workshops, in the destination surrounding area / current position Note: The selection of categories available for various places can vary.
Page 32
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Special destinations - national destinations As your special destination you can select motorway junctions, motorway serv- ice stations, airports and border crossings from the entire region covered by the navigation CD that you are currently using. All you need to know to use this feature is the name of the destination that you require.
Special destinations - position surrounding area You can select special destinations relevant to the area around your current vehicle position. Plus Point: This is helpful, for instance, if you are looking for the nearest petrol station. Press the NAV button 7. The last destination in the current navigation memory bank is displayed for seven seconds.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP To access destinations from the destination memory, press the NAV button 7. The last destination in the current navigation memory bank is displayed for seven seconds. After the seven seconds have elapsed or after the ESC button 8 has been pressed, a menu for selecting the destination type (CITY or SPECial DESTinatioN) is displayed.
Navigation (route guidance) N1 NAVI Starting navigation NEW DESTN... Once you have entered a destination, the destination address appears in the display. If you want to start a navigation session in order to be guided to this BERLIN, UNT destination, ER DEN LIN press the OK button ;.
Page 36
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Plus Point: If you deviate from the recommended route, the system auto- FM 1 EUROPE matically calculates a new route from the current vehicle position to the already entered destination. 07p16 Driving recommendations T M C B6/WESTSCH The visual driving recommendations appear in the middle of the display.
Cancelling navigation (route guidance) FM 1 EUROPE To cancel an active navigation session, press the ESC button 8. CANCEL A confirmation request appears. ROUTE T M C If you are sure you want to cancel navigation, GUIDANCE? press the OK button ;. Dynamic navigation During dynamic navigation, the TravelPilot analyses digital traffic information messages and uses this information when planning the route.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP The latest message appears in the display. The message number and OO1 / OO3 the number of messages in memory are displayed in the top line. OO1 is always the latest message. If no messages are stored in memory, an appropriate notice will be displayed.
Note: For this reason try, if possible, to insert the navigation CD whilst still on the motorway so that this orientation process is speeded up. FM 1 EUROPE Bypassing a traffic jam during navigation TRAFFIC JAM... Alongside the ability to automatically bypass traffic jams with the aid of the dynam- ic navigation feature, the TravelPilot also gives you the option of manually entering T M C traffic jams or blocked sections of road during an active navigation session.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Defining route options ROUTE OPT You can customise the route to suit your requirements at any time, even during ROUTE OPTIONS an active navigation session. DYNAMIC T M C The configurable parameters are: ROUTE –...
If you want to close the selection menu, press the OK button ;. If no navigation session is active, the audio source will be displayed again. If navigation is active, you will be taken to the navigation session. Note: If you change the route options whilst a navigation session is active, the route will be recalculated.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Destination memory In the destination memory you can store destinations that you want to navigate to at some other point in time. You can also set your current position as a posi- tion marker and then access it from memory at some other point in time to use it as your destination.
Page 43
Storing the currently active destination in the destination memory N1 NAVI You can store the currently active destination of the navigation session in the destination memory. CURRENT DESTN During navigation, select the memory bank N1...N4 in which you want to BERLIN, UNT store the destination.
Page 44
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP button <. Press the N1 NAVI The current position is displayed. Whilst the position is being displayed, press one of the 1 - 6 buttons > CURRENT POS. for longer than two seconds to store the position marker to that button. UNTER DEN The text input line is displayed.
Radio mode FM 1 EUROPE This TravelPilot is equipped with an RDS radio receiver. Many of the receivable R D S FM stations transmit a signal that not only carries the programme but also addi- tional information such as the station name. O3 45 The station name appears in the display as soon as it is received.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Switching REG on/off Press the MENU button 1. button : until REG appears in the display. ON Keep pressing the R D S or OFF is displayed alongside REG. button :. O3 45 To switch REG on/off, press the Press the MENU button 1 or OK ;.
Tuning into a station There are various ways of tuning into a station. Automatic seek tuning button :. Press the The unit tunes into the next receivable station. Note: You can adjust the sensitivity of station seek tuning. For fur- ther information, read the section entitled “Setting seek tuning sen- sitivity”...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Storing stations Storing stations manually Select the required memory bank, i.e. FM1, FM2, FMT, or one of the MW or LW wavebands. Tune into the required station. Press one of the 1 - 6 station buttons > for longer than two seconds to store the station to that button.
Scanning receivable stations (SCAN) FM T SCAN You can briefly play (scan) all the receivable stations. The scanning time is 10 seconds. R D S Starting SCAN O3 45 Keep the OK button ; pressed for longer than two seconds. Scanning begins.
Page 50
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Switching traffic information priority on/off FM 1 EUROPE Press the TRAF button @. Traffic announcement priority is active when the symbol lights up in R D S the display. O3 45 Notes: You will hear a warning beep, if you leave the reception area of a traffic information station that you are currently listening to.
CD drive. CD-Rs (CDs that you have “burned” yourself) can generally also be played. Due to the varying quality of CDs, Blaupunkt cannot guarantee that this will work properly. CD-RWs cannot be played. To ensure the system functions properly, only use CDs labelled with the com- pact disc logo.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Carefully insert the CD with the printed side uppermost into the unit’s CD compartment. Push the CD until you feel some resistance. From this point onwards, the CD will be drawn in automatically. CD playback begins automatically after the CD has been checked.
Selecting tracks You can select tracks directly whilst a CD is playing. To select the next track, button :. press the button :, the first If the last track has been reached and you press the track of the CD will be selected. To repeat the current track or select the previous track, button :.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Scanning all tracks on a CD (SCAN) TO2/ 1O SCAN If you want to briefly play all tracks on a CD, proceed as follows: Keep the OK button ; pressed for longer than two seconds. All the tracks on the CD are briefly played in ascending order.
CD changer mode You can use the following Blaupunkt CD changers with the Travel-Pilot: – CDC - A08 – IDC - A09 Please refer to the installation and connection instructions supplied with your CD changer for information on how to install the CD changer in your vehicle and connect it to the TravelPilot.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Selecting CDs To select a CD, button : until the number of the required CD keep pressing the is displayed. CD playback begins. Selecting tracks To select the next track, button :. press the button :, the first If the last track has been reached and you press the...
Random play (MIX) MIX CD You can play the tracks on a CD or all the CDs in the changer in random order. M I X Random play MIX for all tracks on a CD O9:53 To only play the tracks on one CD at random, keep pressing the 2 MIX button >...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Scanning all tracks on all CDs (SCAN) SCAN If you briefly want to play (scan) all the tracks on all the inserted CDs, keep the OK button ; pressed for longer than two seconds. All the tracks are scanned starting from the current track.
Cancelling repeat To cancel the repeat function, keep pressing the 5 RPT button > until RPT no longer appears above the playing time display. Playback is then continued in ascending track order. Activating / deactivating traffic announcements (CD changer) TO1/ 12 D1O To switch traffic announcement standby on / off (see the section entitled “Traffic information”...
INTRODUCTION NAVIGATION RADIO MODE CD MODE REMOTE CONTROL CD CHANGER SETUP Steering wheel remote control The RC10 steering wheel remote control allows you to safely and conveniently access some of the TravelPilot’s primary functions from your steering wheel. and OK buttons on the remote control have the same functions as they do on the TravelPilot.
Muting You can mute the device’s volume using the remote control. Press the button. Cancelling mute If you want to cancel mute, press the button again or press the V+ or V- button. INTRODUCTION NAVIGATION RADIO MODE CD MODE REMOTE CONTROL CD CHANGER SETUP...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Setup - basic settings Setup mode allows you to adjust the TravelPilot’s basic functions to suit your needs. You can change the following device functions: ON VOLUME - Setting the maximum power-on volume NAVI VOLUME - Setting the navigation volume TA VOLUME - Setting the volume for traffic announcements...
Setting the maximum power-on volume - “ON VOLUME” ON VOLUME When the device switches on, it always plays at the volume level that was heard last. You can limit the power-on volume by setting a maximum value. R D S Press the MENU button 1.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP When you have finished making your changes, press the MENU button 1 or OK ;. If you do not want to apply the changes, press the ESC button 8. Setting the minimum volume for traffic announcements - “TA VOLUME”...
To help you configure the setting more easily, the volume will be increased / decreased as you make your changes. When you have finished making your changes, press the MENU button 1 or OK ;. If you do not want to apply the changes, press the ESC button 8.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Displaying scrolling text NAME Some radio stations use the RDS signal to transmit advertising or other informa- tion instead of their station name. These scrolling texts appear in the display. R D S You can deactivate the scrolling text display.
Switching the regional function on/off - “REG” Press the MENU button 1. button : until REG appears in the display. ON Keep pressing the R D S or OFF is displayed alongside REG. O3 45 button :. To switch REG on/off, press the When you have finished making your changes, press the MENU button 1 or OK ;.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Setting seek tuning sensitivity SEEK SENS You can choose whether the system should only tune into stations with a strong reception or whether it can also tune into those with a weak reception. R D S Press the MENU button 1.
The minutes flash. button :. Set the minutes by pressing the When you have finished making your changes, press the MENU button 1 or OK ;. If you do not want to apply the changes, press the ESC button 8. Setting the day/night display brightness You can adjust the brightness separately for day and night to suit your prefer- ences.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Display contrast CONTRAST 6 You can adjust the display contrast to suit your preferences. Press the MENU button 1. R D S button : until CONTRAST appears in the dis- Keep pressing the O3 45 play.
Note: Navigation voice output depends on the navigation CD being LANGUAGE used. The display content will be displayed in the selected language but the voice output might only be available in English. R D S To switch between the languages, press the MENU button 1.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Calibrating the device INSTALL The installation menu contains all the necessary items for preparing the Travel- NEW INSTLL Pilot for operation once it has been installed. TYRE CHNGE SYS TEST New installation MAN.
Page 73
The connection of the positive ignition terminal is tested next. INSTALL An ignition key appears in the display. Switch on the ignition within approx. the next 10 seconds. If the switching signal was detected, a smiling face appears. The reversing light function is tested next. A gear switch symbol appears in the display.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Calibration after a tyre change INSTALL It may be necessary to recalibrate the TravelPilot after a tyre change. NEW INSTLL Select TYRE CHaNGE from the installation menu. TYRE CHNGE Please drive along a route of between 4 and 10 miles with good GPS reception.
Carrying out the system test INSTALL You have the option of carrying out a system test. The system checks the GPS antenna and whether the reversing signal and the vehicle ignition are correctly NEW INSTLL connected to the system. TYRE CHNGE Select SYStem TEST from the installation menu.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Adjusting the audio settings and sound distribution settings The TravelPilot allows you to adjust the bass and treble for each audio source. Changes to the balance and fader sound distribution settings affect all the audio sources jointly.
Setting the left/right sound distribution (balance) BALANCE O To adjust the balance, press the AUD button ?. R D S BASS appears in the display. O3 45 button : until BALANCE appears in the dis- Keep pressing the play. button : to adjust the balance. Press the When you have finished making your changes, press the AUD button ? or OK ;.
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Equalizer DIGITAL EQ This unit is equipped with a digital equalizer. R D S The equalizer has five filters. You can individually boost or reduce one frequen- cy for each of the five filters (GAIN +8 to -8). O3 45 The following filters are available: SUB LOW EQ...
Help adjusting the equalizer Start by adjusting the treble and mid levels and finish by setting the bass levels. Sound Impression / problem Measures Bass sound is too weak Boost bass with Frequency: 50 to 100 Hz Level: +4 to +6 Dirty bass Reduce the lower mid level with Booming sound...
INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP Adjusting the equalizer Press the AUD button ?. button :. Select DIGITAL EQ using the button :, select the SUB LOW EQ, LOW EQ, MID EQ, Using the MID HIGH EQ or HIGH EQ filter that you want to adjust. Press the OK button ;.
Specifications Amplifier Output power: 4 x 25 watts sine in accordance with DIN 45 324 at 14.4 V 4 x 45 watts max. power Tuner Wavebands: 87.5 - 108 MHz 531 - 1,602 kHz 153 - 279 kHz FM frequency response: 35 - 16,000 Hz Frequency response: 20 - 20,000 Hz...