Output Terminals - Sanyo TLS-9024P Instruction Manual

OUTPUT TERMINALS

SW OUT Terminal
When recording, a pulse signal is output at the SW OUT
terminal.
This terminal is usually connected to the switch input
(SW IN) of devices like a camera switcher unit, or a
quad compressor.
FIELD: 20 msec.
FRAME: 5 msec.
SW OUT Terminal Output Setting
1
Press the MENU button until the (SET UP 4) menu
is displayed.
ø The FIELD (or FRAME) setting is flashing.
@@@@@@@<SET@UP@4>
öSW@OUT
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@3H@@@@@@@@@@@@Y
öTHREAD@CHECK@@@Y
öVIDEO@LOSS@@@@@N
öREC@SPEED@@@@@@N
NOTE:
œ If "TIMING" is set to FRAME (see step 4),
"FRAME" will be indicated instead of "FIELD".
2
Turn the SHUTTLE ring, to set the desired pulse
signal interval.
Available settings are:
FIELD . . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field
FRAME . . . . . 01, 02, 03, 04, 05, 10, 30 or 60
frame
3
Turn the JOG dial clockwise until the "TIMING"
setting is flashing.
4
Turn the SHUTTLE ring, to set "FIELD" or "FRAME".
FIELD . . . . . . 1 pulse is output after each set
number of fields.
FRAME . . . . . 1 pulse is output after each set
number of frames.
5
Turn the JOG dial clockwise until the "3H" setting is
flashing.
6
Turn the SHUTTLE ring, to set the desired "3H"
mode.
Y . . . . . . . . . . When recording in 3-hour mode,
a pulse signal is output.
N . . . . . . . . . . When recording in 3-hour mode,
a pulse signal is not output.
7
Press the SEARCH/AUDIO ON button to save the
settings.
5V (H)
(Output impedance: 5.7 k )
0V (L)
TAPE END OUT Terminal
œ During recording, when the end of the tape is
reached or when the tape counter reading indicates 2
hours 57 minutes or more, the output becomes 0V
(Low).
œ To reset the output, press the STOP or EJECT
button.
œ During autorepeat recording, when the end of the
tape is reached, the output becomes 0V (Low) for
about 2 seconds only.
Tape end or 2 57
H
Output reset
TAPE END OUT Terminal Output Setting
1
Press the MENU button until the (SET UP 3) menu
is displayed.
@@@@@@@<SET@UP@3>
öALARM@MODE@@@@@@@Y1
öALARM@SPEED@@@@@@3H
öALARM@DURATION@@@20S
öTAPE@END@MODE@@@@REW
öTAPE@END@OUT@@@@@-3M
öCLOG@DETECT.@@@@@Y
öRS-232C@@@@@@@@@@19200
2
Turn the JOG dial, until the "TAPE END OUT"
setting is flashing.
3
Turn the SHUTTLE ring, to select the desired output
mode.
–3M . . . . . . . The output becomes 0 V (Low)
END . . . . . . . The output becomes 0 V (Low)
4
Press the SEARCH/AUDIO ON button to save the
setting.
32
00
M S
5V (H)
(Output impedance: 5.7 k )
0V (L)
when the tape counter reaches
"2 57 00 " and/or when the
H M S
tape reaches the end.
when the tape reaches the end.
English