Related Manuals for Zanussi ZUD 7154
Summary of Contents for Zanussi ZUD 7154
- Page 1 KÜHL- GEFRIERSCHRANK REFRIGERATEUR- CONGELATEUR TWEEDEURS- KOELKAST FRIDGE-FREEZER ZUD 7154 BEDIENUNGSANLEITUNG MODE D’EMPLOI GEBRUIKSAANWIJZING INSTRUCTION BOOKLET 2222 257-14...
- Page 2 WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings.
-
Page 3: Table Of Contents
Environment Protection Installation During normal operation, the condenser and This appliance does not contain gasses compressor at the back of the appliance heat which could damage the ozone layer, in up considerably. For safety reasons, minimum either its refrigerant circuit or insulation ventilation must be as shown in the relevant materials. -
Page 4: Installation
INSTALLATION Cleaning the interior If this appliance featuring magnetic door seals is to replace an older appliance Before using the appliance for the first time, having a spring lock (latch) on the door or wash the interior and all internal accessories lid, be sure to make that spring lock with lukewarm water and some neutral soap unusable before you discard the old... -
Page 5: Location
Location Fig. 1 Fig. 1 This appliance is designed to be built-in to a space having the dimensions given in Fig. 1. Fig. 2 The height of the appliance can be altered if required by means of adjustable feet situated at 100-170 D506 its base (Fig. -
Page 6: Fitting A Decorative Door Panel
Fitting a decorative door panel Fig. 6 Important :The components needed to fit the decorative panel have been pre-fitted on the appliance. The brackets are secured to the panel by means of the 7 Ø 3.5x13 screws supplied. Before starting to fit the panel, remove the large top bracket by unscrewing -1cm the screws and adjusting pins prefitted on... - Page 7 Fig. 11 Fig. 11 Once the door has been correctly aligned, tighten the holding nuts on the fixing brackets and attach the appliance to the adjacent units and the bottom of the work surface (Fig. 11). D517 Fig. 12 Fig. 12 If the appliance has been fitted into a space 820 mm high and the maximum height of the base plate is 100 mm, fit the front cover plate by...
-
Page 8: Electrical Connection
Changing the opening direction of the door Fig. 15 Having changed the opening direction of the appliance door, it is advisable to also change the opening direction of the freezer compartment door. To do this, proceed as follows: Fig. 15 Unscrew the two fixing screws to remove the lower hinge from the door (Fig. -
Page 9: Use
Operation drawer(s). For safety, store in this way only one or two days at the most. Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat Cooked foods, cold dishes, etc: these should knob, clockwise, beyond the «O» (STOP) be covered and may be placed on any shelf. -
Page 10: Storage Of Frozen Food
Wrap up the food in aluminium foil or polythene Thawing and make sure that the packages are airtight. Deep-frozen or frozen food, prior to being used, It is advisable to show on the single food packet or on the write-on produce strips to be found on can be thawed in the refrigerator compartment the front part of the storage baskets the or at room temperature, depending on the time... -
Page 11: Positioning The Door Shelves
Fig. 19 Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be adjusted in height. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes off, then reposition as D006 required. -
Page 12: Maintenance
MAINTENANCE Unplug the appliance before carrying out any Interior light maintenance operation. The light bulb inside the refrigerator Warning compartment can be reached as follows: This appliance contains hydrocarbons in its cooling unscrew the light cover securing screws; unit maintenance and recharging must therefore only be carried out by authorized technicians.