Harman Kardon AVR 155 Owner's Manual page 28

System Configuration
When the
CHANNEL ADJUST
appears, the test tone is off. Use the
Navigation Button to select any channel
for adjustment using an external source, such as
a test disc, from which to judge the output levels.
After the fi cursor is pointing to the channel to
be adjusted, press the / Navigation Button
‹ ›
to raise or lower the output level.
However, before proceeding with any manual
adjustment we recommend that you first use the
AVR's internal test tone generator and automatic
sequencer to send a tone to each channel so that
you may verify that all speaker connections have
been properly made.
5. To turn the test tone on and have it automati-
cally circulate among the channels where a
speaker has previously been configured (see
page 21), press the Navigation
⁄ / ¤
until the fi cursor is pointing to
Button
the line on the menu.
TEST TONE SEQ
Next, press the / Navigation Button
‹ ›
until is shown. At this time
AUTO
the test tone will immediately begin to circu-
late clockwise around the room, playing for
two seconds in each speaker before switching
to the next speaker position. The fi cursor will
blink next to the active speaker to indicate
which speaker the sound should be coming
from.
IMPORTANT NOTE: Because this test noise will
have a much lower level than normal music, the
volume must be lowered after the adjustment for
all channels is made, but BEFORE you return to
the main menu and the test tone turns off.
NOTE: Remember to verify that the speakers have
been properly connected. As the test noise
circulates, listen to make certain that the sound
comes from the speaker position shown in the
Main Information Display Ò. If the sound
comes from a speaker location that does NOT
match the position indicated in the display, turn
the AVR off using the Main Power Switch 1
and check the speaker wiring or connections to
external power amplifiers to make certain that
each speaker is connected to the correct output
terminal.
28 SYSTEM CONFIGURATION
menu first 6. After checking for speaker placement, let the
test noise circulate again, and listen to see
⁄ / ¤
which channels sound louder than the others.
Using the front left speaker as a reference,
press the
‹ / ›
to bring all speakers to the same volume level.
When one of the
test noise circulation will pause on the channel
being adjusted to give you time to make the
adjustment. When you release the button, the
circulation will resume after five seconds. The
on-screen cursor fi and the test noise can also
be moved directly to the speaker to be
adjusted by pressing the
on the remote.
7. Continue to adjust the individual channels
until the volume level sounds the same from
each speaker. Note that adjustments should be
made with the
remote only, NOT the main volume controls.
Buttons on the remote
buttons is pushed, the
‹ / ›
buttons
⁄ / ¤
Buttons on the
‹ / ›
If you are using a sound-pressure level (SPL)
meter for precise level adjustment with the test
tone, open the main Volume Control
–15dB and set the individual output level for
each channel so that the meter reads 75dB,
C-Weighted Slow. After all settings are made turn
the main volume down.
You may also make these same adjustments with
complete manual control over the channel being
adjusted by pressing the Navigation
⁄ / ¤
until the fi cursor is pointing to the
Button
line on the menu and then
TEST TONE SEQ
using the / Navigation Button
‹ ›
select in the highlighted video. In the
MANUAL
mode, the test tone will also start
MANUAL
immediately, but the tone will only be moved to
another channel by pressing the
⁄
Navigation Button . When the manual
sequencing mode is active, the tone is turned off
by pressing the Navigation Button
⁄ / ¤
until the fi cursor is pointing to the
line and the / Navigation Button
TONE
‹ ›
is then pressed to select
OFF
highlighted video.
If you find that the output levels are either
uncomfortably low or high, you may repeat the
procedure. Return to Step 2 and adjust the
master volume either slightly higher or lower to
accommodate your particular room layout and
your tastes. You may repeat this procedure as
many times as necessary to achieve a desired
result. In order to prevent possible damage to
your hearing or your equipment, we emphasize
that you should avoid setting the master volume
above 0dB.
When all channels have an equal volume level,
the adjustment is complete. Use the
Buttons to move the fi cursor next to the
line, and press the
TEST TONE
until the word OFF appears to stop the
test tone.
Note that any time a given surround mode is
selected, even for a different source input, these
output level settings will be used. However, the
output levels must be set independently for each
surround mode, including variations such as Dolby
Pro Logic II-Movie versus Dolby Pro Logic II-Music.
Although this may seem to be tedious, it is neces-
sary in order to optimize the AVR's performance
when differing methods are employed to steer the
audio materials to the various channels. However,
the AVR will carry over the settings for one mode
to the same mode in a different channel configu-
ration, such as Dolby Pro Logic II-Movie and Dolby
Pro Logic II-Movie. If you wish, as a shortcut to
get started quickly, you may set the levels for
Dolby Pro Logic II-Movie and copy down those
settings, reentering them for each of the Dolby
modes and entering the settings only for those
speakers which are available for each mode.
to
to
/ ¤
TEST
in the
/
⁄ ¤
/ Buttons
‹ ›