Page 1
To ensure the smooth handling of your warranty please write the serial number of your device into the box. In the case of warranty you are expected to send it to- gether with a copy of your invoice to your nearest TEAC sales representative.
1. IMPORTANT SAFETY INSTRUCTIONS CAUTION: – Read all of these instructions. – Save these instructions for later use. – Follow all warnings and instructions later on the audio equip- ment. 1) Read Instructions – All the safety and operating instructions should be read before the product is operated.
Page 6
10) Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to pro- tect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similiar surface.
Page 7
17) Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 18) Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the fol- lowing conditions: a) When the power supply cord or plug is damaged.
CopyStation). To make copies no other devices like PCs or anything else are needed. The TEAC Dupli CopyStations can be used to duplicate DVD/CD-ROM material of which you own copyright or for which you have appropriate permission.
CD-R Dupli 14/40 or CD-R Dupli 7/40 or CD-R Dupli 4/40 1 User's Manual 1 Warranty Booklet 1 Cable used to connect the basic unit to the drive extension unit (TEAC DVD/CD Dupli 14/4 and TEAC CD-R Dupli 14/40 only) 2.2 Installation...
The picture shows the CopyStation TEAC DVD Dupli 4/4 POWER switch Press this switch once to power on the unit, and again to turn it off. The 2 lines LCD displays the menus and submenus available, and also provides information on the status of the current operation, as well as displaying error messages, etc.
Page 11
Button Panel The buttons ENT, ESC, V and W are used to select menu options and to set configuration parameters. Their functionality is described in de- tail in paragraph 3.1 Buttons and LCD. Source Drive The source drive is used to hold the source DVD/CD (original media which shall be copied).
ENTER key of PC keyboards. The button ESC is used to cancel a selected function. After you power on,and the TEAC Dupli CopyStation detects installed hardware like source drive, DVD/CD writer, it will execute a self-test for seconds.
W to select other functions. 3.2 About optional HDD Optionally TEAC Dupli CopyStations are also available with an inte- grated hard disk. This feature allows to make copies not only 1:1 of DVD/CD master media. The optional hard disk also allows to make copies of image files stored on the hard disk.
Page 14
Important During operation do not press any button on your CopyStation, because interruption will harm the device, and DVDs/CDs will be damaged. 3.2.2 Copying Without a HDD If your CopyStation is not equipped with the optional hard disk, the operation procedures will be as follows: O Place a source DVD/CD into the source drive.
4. FUNCTIONS There are 12 functions: Copy, Test, Test & Copy, Verify, Compare, Prescan, Disc Info, Select Source, Image, Edit Track, Setup and Ad- vanced Setup. Among the 12 functions, Edit Track is designed exclu- sively for editing a collection of favorite songs from CDs. During opera- tion if you do not understand an LCD message, you can see Appendix.
When copying comes to an end, LCD will show the results as follows. The passed DVDs/CDs will eject automatically. 1.Copy OK: 03 4.2 Test Function 2.Test is to simulate the copying progress. When simulation finishes, there will be no data really written into DVDs/CDs. Select function 2.
LCD will show the testing information as follows. Testing- DVD 4213.4MB d:20:15 When the test comes to an end, LCD will show the results as follows. 2.Test OK: 03 Note Stopping the test halfway does not affect the DVD-R/RWs or CD-R/RWs, but if the DVD-RWs/CD-RWs contain impor- tant data, they may be destroyed.
When the test finishes, actual copying will begin as shown below. Copying- DVD 0% 4213.4MB d:20:15 When the whole process finishes, LCD will show the results as follows. 3.Test & Copy OK: 03 4.4 Verify Function 4.Verify is to examine if the target DVDs/CDs can be read correctly after copying.
When verification comes to an end, LCD will show the results as fol- lows. 4.Verify OK: 03 4.5 Compare Function 5.Compare is to make a comparison between the source DVD/ CD and the target DVDs/CDs after copying. Select function 5. Put the source DVD/CD onto source drive and the target DVDs/CDs onto the writers.
Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the comparison is identical, LCD will show the message as follows. Src: 02 DVD-RW Identical If comparison fails, LCD will show the failure.
Press ENT to prescan. LCD will show the scanning information as fol- lows. Scaning- DVD 0% 4213.4MB 40:40 When scanning finishes, and the source DVD/CD can be read cor- rectly, LCD will show the results as follows. PreScan OK! 4.7 Disc Info Function 7.Disc Info is to show the basic information of source DVD/ Select function 7.
4.8 Select Source Function 8.Select Source is to let you select the data on DVD/CD source drive, DVD/CD Writers or the optional HDD as the source from which copying will be done. Select function 8. 8.Select Source Press ENT, and then press V W to select the source as shown below. Src: DVD-ROM 01 IDE1 Master After selecting the source, you can press ENT, and LCD will show the...
4.9 Image Function 9.Image is valid only when you have installed an optional hard disk. This function includes 6 parts. They are Load, Delete Image, Image Info, Compare Image, Select Partition and Select Src Drive. The loaded data is called an image file. Select function 9.
After the image file is successfully loaded, LCD will show the results as follows. Image load OK If there is an image file existing in the current partition, the system will ask you whether to overwrite it or not. Please use V W to confirm Yes or No.
Page 25
After the image file is deleted, LCD will show the results as follows. Partition A: Image is deleted 4.9.3 Image Info This function is to show the basic information of an image file stored in a particular partition of the optional hard disk. First, select the function by pressing W.
Page 26
Press ENT, and LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 1:05:06 When comparison comes to an end, LCD will show the results as fol- lows. Compare OK: 1 Fail: 0 Diff: 0 Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total:...
4.9.5 Select Partition This function is to select a partition in the optional hard disk. First, select the function by pressing W. 9-05.Image P: A Select Partition Each partition will occupy 5GB. The number of partitions is dependent on the optional hard disk’s capacity. The partitions is alphabetically ar- ranged.
First, select the function by pressing W. 9-06. Image P: A Image Src Drive Then, use V W to select source drive or any of the DVD/CD writers as the source. Select Img Src: 01 IDE1 DVD-ROM After selecting the source such as DVD-ROM, you can press ENT, and LCD will show the message as follows.
4.10.1 CD to CD On the above figure press ENT, and you will enter the following figure. Here the function CD to CD is to let you select a track or more from CD-ROM, and then copy into blank CD-R/RWs. 10-01.
Page 30
After selecting, please use V to move to the “End” menu as shown below. Select Track: End 1Trk03:25 Press ENT to finish the CD editing, and use V W to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 1/10 - >...
Page 31
The CopyStation will ask if you want to keep editing. Please use V W to confirm Yes or No. as shown below. Continue edit next Disc?Yes If you want to keep editing, the current source CD will eject automati- cally, and the system will ask you to insert another new CD as shown below.
Page 32
Press ENT to finish the CD editing, and use V W to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 2/10 - > 2/2 On the above figure 2/2 means the second track of all tracks we have selected, and so far we have selected two tracks from two different CDs.
Page 33
On the above figure Press ENT. The CopyStation will ask if you want to close all CDs’ sessions. Please use V W to confirm Yes or No as shown below. Close all disc’s session? Yes After deciding to close, LCD will show the message as follows. Closing Session Please wait--- 4.10.2 CD to HDD...
Page 34
Suppose we decide to select the first track, then press ENT. A “+” will appear beside 1/10 as shown below. But pressing ENT again may can- cel the selection. Select Track: +1/10 03:25 After selecting, please use V to move to the “End” menu as shown below.
Page 35
The system will ask if you want to keep editing. Please use V W to confirm Yes or No. as shown below. Continue edit next Disc?Yes If you want to keep editing, the current source CD will eject automati- cally, and the system will ask you to insert another new CD as shown below.
Page 36
Then, the track as an image file will be loaded into the optional HDD. LCD will show the loading information as follows. Load- P0 -24X Edit 2/10 - > 2/2 When loading comes to an end, LCD will show the message as fol- lows.
Page 37
When burning finishes, LCD will show the results as follows. Burn Complete ! OK: 03 On the above figure press ESC to enter the following figure. Now press W to move the data from the optional HDD template into a certain partition.
If the chosen partition has contained image data, the system will ask to overwrite or keep the data. Here please use V to overwrite. Image Exists Overwrite?Yes After pressing V, LCD will show the moving information as follows. Moving to P: A When moving finishes, LCD will show the results as follows.
Page 39
Use V W to select the track you want to play. Select Track: 1/10 03:25 After selecting and pressing ENT, LCD will show the playing informa- tion below. Playing Track-1 00:00 / 03:25 4.10.4 Close Session This function is to close CDs and let no data written into. After closing, you can put the CDs on any normal player and listen.
Press ENT to enter the following figure. Closing Session Please wait--- When closing finishes, LCD will show the results as follows. Closing Complete OK :3 Fail :0 4.11 Setup Function 11.Setup lets you change the default settings. Once you change a setting, remember to press ENT to save it. However, it is suggested to use the defaults for the optimal operation.
4.11.1 Language On the above figure press ENT, and you will enter the following figure. The function Language lets you select a language in which messages can be shown on LCD. 11-01. Setup Language Press ENT to enter the following figure. Here LCD only supports Eng- lish.
4.11.3 Read Speed On the above figure press ESC and W to enter the following figure. The function Read Speed lets you control the reading speed of target DVDs/ CDs. 11-03. Setup Read Speed Press ENT to enter the following figure. The default is maximum, but there are still other choices like 32X, 16X and 8X.
4.11.5 Startup Menu On the above figure press ESC and W to enter the following figure. Startup Menu lets you select any one of the functions except Adv Setup as the first item appearing on the menu whenever you turn on the CopyStation.
4.11.7 Auto Compare On the above figure press ESC and W to enter the following figure. Auto Compare is to compare automatically the source DVD/CD and the target DVDs/CDs after copying. 11-07. Setup Auto Compare Press ENT to enter the following figure. The default is Off. Press W to select On.
4.11.9 Eject Disc On the above figure press ESC and W to enter the following figure. Eject Disc provides three choices. They are Eject Good Only, Eject All Disc, and Do Not Eject. Eject Good Only means that the DVDs/CDs will eject automatically only when they are copied successfully.
Press ENT to enter the following figure. The default is On. Press W to select Off. Burn On The Fly If your CopyStation doesn’t have the optional hard disk available, LCD will show the message as follows. No Valid HDD ! 4.11.11 Burn Mode On the above figure press ESC to return to Function 11, and then select part 11 Burn Mode as the following figure shows.
On the above figure press ESC and W to enter the following figure. Device Info shows the information of the source drive and any of the DVD/CD Writers you have installed. 11-13. Setup Device Info Press ENT to enter the next figure. 01 IDE1 Master DVD-ROM : TEAC 4. Functions...
Page 48
Press ENT to enter the next figure. DVD-ROM DVD-116 1.22 Press W twice to enter the next figure. 02 IDE2 Master DVD-RW : TEAC Press ENT to enter the next figure. DVD-RW DVR-103 1.80 4.11.14 System Info On the above figure press ESC and W to enter the following figure.
Page 49
4.11.15 Quick Erase On the above figure press ESC and W to enter the following figure. Quick Erase is to erase the data on the DVD/CD Re-Writeable discs quickly. 11-15. Setup Quick Erase Press ENT to enter the next figure. Use V W to confirm Yes or No. All data will be lost, erase?Yes After confirming Yes and pressing ENT, LCD will show the message as...
4.11.16 Full Erase On the above figure press ESC and W to enter the following figure. Full Erase is to erase the data on the DVD/CD Re-Writeable discs com- pletely. Compared with Quick Erase, Full Erase takes longer time to do the job.
4.12 Adv Setup Function 12 Adv Setup lets you change the system configuration. This function includes 13 parts. They are UnderRun Protect, Overburn, Read Error Skip, Format HDD, Verify HDD, Burn-in, H/W Diagnostic, Load Default, CD+G, ISRC and Switch Link-Host. On the above figure press ESC to return to Function 11.
4.12.2 Overburn On the above figure press ESC and W to enter the following figure. Overburn lets you decide whether to copy beyond the limit or not. 12-02. Adv Setup Overburn Press ENT to enter the following figure. The default is Off. Press W to select On.
4.12.4 Format HDD On the above figure press ESC and W to enter the following figure. Format HDD is to partition the optional hard disk. But before format- ting, all data on the optional hard disk will be deleted. 12-04. Adv Setup Format HDD Press ENT to enter the next figure.
Page 54
Press ENT to enter the next figure. Use V W to confirm Disk or Parti. Verify Disk or Partition? Disk Press ENT to verify. After verification LCD will show the results as fol- lows. Verify Hard Disk 4.12.6 Burn-in On the above figure press ESC and W to enter the following figure. Burn-in is to simulate the copying progress many times.
Page 55
Press ENT and use V W to select the time of simulation such as 1, 2, 3...1000 or Run Continuous. The figure below shows Run Continuous. Sel burn-in num: Run Continuous Press ESC, ENT, W to select Erase & Copy as the following figure shows.
Page 56
Press ENT to enter the next figure. Follow the instructions on LCD to do the button test. After that, the CopyStation will do the self-test of SDRAM, the hardware connection test and flash test. All test results will be shown on LCD. It is the easiest way to know if the system can work well.
When default loading finishes, LCD will show the results as follows. Load Default 4.12.11 CD+G On the above figure press ESC and W to enter the following figure. CD+G is a kind of special copying format. This function supports the special format.
Page 58
Press ENT to enter the next figure. The default is Off. Press W to select ISRC 4.12.13 Switch Link-Host On the above figure press ESC and W to enter the next figure. Switch Link-Host lets you switch to the link-host mode if your CopyStation has connected with a PC.
5. TROUBLESHOOTING 5.1 About LCD After powering on if there is no LCD, please check if the connection of power cord is firm and the environment of power outlet is normal. 5.2 About Error Messages During Copy, Test, Compare and Verify, etc. if you press ESC to abort, an error message will appear on LCD.
5.4 About Buttons If you press any one of the four buttons on the panel, but there is no response, it is likely that the button cannot function well. Please inspect the jumper setting. 5.5 About DVD/CD Disc Not Readable After copying if the DVD/CD disc is not readable, please use Compare to examine, or get another source drive to test.
6. TECHNICAL SUPPORT In case the TEAC Dupli CopyStation does not operate normally in the environment specified in this manual, contact the representative from whom you purchased the drive or our nearest sales office to you. Technical Service Depots (Europe)
7. SPECIFICATION 7.1 DVD/CD Dupli Model DVD Dupli 14/4 DVD Dupli 7/4 DVD Dupli 4/4 DVD-ROM TEAC DV-516E Performance max. 48 x CD, max. 16 x DVD DVD-Writer 14 x TEAC DV-W50E TEAC DV-W50E TEAC DV-W50E Performance max 4 x DVD-R / 2 x DVD-RW / max 16 x CD-R / 8 x CD-RW...
APPENDIX: LCD MESSAGES A.1 Normal Conditions: Initialize SDRAM ......Initialize the memory of the system. Detect Drives ..Detect what drives are connected with the system. User Abort ..........Cancel the job during operation. Analyzing ............Analyze the source disc. Source Drive Not Ready ....
Press a Key to Eject Good Disc ... Press any ket to eject the good disc after copying Press a Key to Eject Fail Disc ..Press any key to eject the failed disc after copying. DVD-RW does not Support the Func ..DVD-RW doesn’t support this function.
Verify Disk or Partition? ....Do you want to verify the hard disk or just a partition? Verify Hard Disk OK! ....The hard disk is verified successfully. Verify Hard Disk Fail! ..... The hard disk is not verified successfully. Verify Partition Header! ........