Panasonic TH-42LFP30W Operating Instructions Manual page 50

Options Adjustments
Item
Locks the input switch operation.
Off
Notes:
Input lock
• Only the adjusted signal is displayed (see page 15).
• Input switch can be used when this is set to "Off".
Off
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
On: Locks all the button on main unit.
Button lock
Sets Button lock with the unit buttons in the following procedure.
Off: Press
MENU&ENTER: Press
On: Press
Off
Off: You can use all of the buttons on the remote control.
User1: You can only use
Remocon User level
User2: You can only use
User3: Locks all the buttons on remote control.
Enable: Enables the "Off-timer function".
Off-timer function Disable: Disables the "Off-timer function".
Note: When "Disable" is set, the Off-timer is cancelled.
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Initial Power Mode
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Off
You can set the power-on delay time of the displays to reduce the power load, when you press
turn on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display's setting individually.
Off:
Power On Screen
1 to 30 (sec.): Set the power-on delay time (second).
Delay
Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
Clock Display
Whether to show/hide No activity power off Precautions at the time of power ON is set.
Power On Message
On: The warning precautions are shown at the time of power ON.
(No activity power
Off: The warning precautions are not shown at the time of power ON.
off)
Note: This setting is enabled only if "No activity power off" is "Enable" (see page 31).
Set this function to maintain the image quality when the product is used in a low temperature
environment of 39 °F/4 °C or lower.
Off: Normal standby operation
On: Image is muted at standby and backlight is turned on when the inside temperature of the display
When this function is set to "On", the following message appears at standby.
Winter Mode
Notes:
• Do not unplug the power cable while using the product with this function "On".
• When this function is set to "On", the power consumption at standby is approx. 100 W.
• Turn this function "Off" to use this product in an environment of 39 °F/4 °C or higher.
Sets the lock setting for the display Power switch.
On: Power switch operation is disabled.
Power Switch Lock
Off: Power switch operation is enabled.
42
VIDEO Component/RGB
On MENU&ENTER
and
four times→Press
four times→Press
four times→Press
User1 User2
,
button on the remote control.
On Standby
Power returns in power On. (Power Indicator : green)
1 2 3.... 30
The display will be turned on at the same time as
After pressing , the display will be powered on with time delay depending on this setting.
Note: When "PRESENT TIME Setup" is not set, the clock is not displayed even
10:00
if "Clock Display" is "On". (see page 27)
is 32 °F/0 °C or lower to prevent decreasing the temperature. Backlight is turned off when the
inside temperature is 50 °F/10 °C or higher.
Winter mode is active.
Adjustments
PC DVI
buttons on main unit.
four times→Press
four times→Press
four times→Press
User3
, , , buttons on the remote control.
HDMI1 HDMI2 Off
four times→Press
four times→Press
four times→Press
is pressed.
button is pressed.
to