Advertisement
Basic Operations
VOLUME +
, iPod & iPhone
and CD
have a tactile dot.
VOLUME +
has a tactile dot.
Loading an iPod
Playing an iPod
Press iPod & iPhone
and power turns on (direct power-on).
"DC OUT" appears in the display (AC only) and the
iPod begins to play automatically.
You can operate the connected iPod by the unit or the
iPod buttons.
To
Press PUSH OPEN
.
Pause playback
The door for the iPod is opened.
Insert your iPod onto the connector.
Stop playback
Close the door until it clicks.
Go to the next
Tips
track
• When using an iPod nano 1st generation/iPod nano 2st generation
(aluminum), you can adjust the position of the connector so that the
Go back to the
iPod is placed in the middle.
previous track
• When using an iPod other than iPod nano 1st generation/iPod nano
Locate a point
2st generation (aluminum), slide the connector to the right.
while listening to
Notes
the sound
• When using the unit with AC, the unit will automatically turned on.
• When connecting an iPod during the playback, the unit continues
Locate a point
the playback of the iPod even after the connection.
while observing
on the iPod
display
Select a menu
Go back to the
previous menu
Notes
• You may use the universal adaptor supplied with your iPod for a
more customized fit. The iPod may be docked without the use of an
adaptor.
• If you connect the iPod when another function is in use, the
To change the cover
function will change to iPod automatically.
• Apple's iPod Universal Dock Adapter (not supplied) can be used
When using an iPod touch/iPhone, you can replace the
with this unit.
cover with the exchangeable lid (supplied).
• To use an iPod, refer to the user's guide of your iPod.
• Before disconnecting the iPod, pause playback.
To use the unit as a battery charger (AC only)
You can use the unit as a battery charger. The charging
status appears in the iPod display. For details, see the
Exchangeable lid (supplied)
user's guide of your iPod.
On copyrights
Remove the cover
• iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• iPhone is a trademark of Apple Inc.
• All other trademarks and registered trademarks are of
their respective holders. In this manual, ™ and ® marks
are not specified.
Playing a CD
1
Press PUSH OPEN/CLOSE
Press the latches on both sides of the door at the
the label side up in the CD compartment.
same time.
To close the CD compartment, press PUSH OPEN/
Remove the cover
.
CLOSE
Shut the door until it clicks.
Insert the exchangeable lid
2
Press CD
The player plays all the tracks once.
Insert the tabs of the exchangeable lid into the
slots.
To
Push the upper part of the exchangeable lid in until
it clicks into place.
Pause playback
Note
Stop playback
Confirm the latches are correctly engaged on both sides.
Go to the next
track
Go back to the
previous track
Locate a point
while listening to
the sound
Locate a point
while observing
the display
Remove the CD
Selecting a CD play mode
Press MENU/MODE
(iPod
on the remote)
until "
1", " ", "SHUF", "SHUF" and " ", "PGM", or
"PGM" and " " appear in the display. Then proceed as
follows:
To Select
Select
Repeat a
"
1"
single track
Repeat all
" "
Press
tracks
iPod & iPhone ( on
Shuffle play "SHUF"
the remote).
To resume play, press it again.
Repeat tracks
"SHUF"
in random
and " "
order
Program
"PGM"
play
(forward) or
(backward)
while playing and hold it until
you find the point.
(forward) or
(backward)
in pause and hold it until you
Programed track
find the point.
Press MENU/MODE
(MENU
on the remote) and
or
to select a menu, and then press
Repeat
"PGM"
programed
and " "
ENTER
.
tracks
Press MENU/MODE
(MENU
on the remote).
To cancel the selected play mode
Press MENU/MODE
repeatedly until the selected mode disappears from the
display.
To check the programed track and playing
order in the display
To check the order of tracks before playing, press
DISPLAY•ENTER
Every time you press the button, the track number
appears in the programed order.
To change the current program
Press
once if the CD is stopped and twice if the CD
is playing. The current program will be erased. Then
create a new program following the programing
procedure.
Tip
You can play the same program again, since the program is saved
until you open the CD compartment.
Listening to the radio
and place a disc with
1
Press RADIO•BAND•AUTO PRESET
(direct power-on) or press RADIO
.
repeatedly on the remote.
Each time you press the button, the indication
changes as follows:
"FM" "AM"
2
Hold down TUNE + or –
digits begin to change in the display.
The player automatically scans the radio frequencies
and stops when it finds a clear station.
If you can't tune in a station, press the button
repeatedly to change the frequency step by step.
When an FM stereo broadcast is received, "ST"
appears.
(CD
on the remote).
Tips
• If the FM broadcast is noisy, press MENU/MODE
Track number
Playing time
on the remote) until "Mono" appears in the display and the radio
will play in monaural.
• If you touch or operate an iPod connected to this unit while
listening to AM/FM, noise may occur. Avoid touching or operating
the iPod in this case.
• If you are listening to the radio with an iPhone connected to the
unit, interference with radio reception may occur. Remove the
Press
iPhone in this case.
• If you hear noise from the AM/FM radio while supplying power to
CD ( on the remote).
an iPod ("DC OUT" indicator appears in the display), press and
To resume play, press it again.
hold MENU/MODE
seconds to stop the power supply to the iPod ("DC OUT" indicator
disappears from the display).
Changing the AM tuning interval
If you need to change the AM tuning interval, do the
following:
(forward) or
(backward)
1
While keeping the RADIO•BAND•AUTO PRESET
while playing and hold it until
and MENU/MODE
you find the point.
power cord from the wall outlet.
(forward) or
(backward)
2
While keeping the RADIO•BAND•AUTO PRESET
in pause and hold it until you
and MENU/MODE
find the point.
power cord to the wall outlet.
PUSH OPEN/CLOSE
The tuning interval is changed and "AM 9" or "AM
10" appears in the display for 4 seconds.
After changing the tuning interval, you need to reset
your preset radio stations.
Presetting radio stations
(MODE
on the remote)
You can store radio stations into the player's memory.
You can preset up to 30 radio stations, 20 for FM and 10
for AM in any order.
1
Press RADIO•BAND•AUTO PRESET
the remote) to select the band.
Then do this
Press
or
to
2
Hold down RADIO•BAND•AUTO PRESET
select the track that you want
on the remote) for 2 seconds until "AUTO" flashes
in the display.
to repeat, then press CD
(
on the remote).
3
Press DISPLAY•ENTER
Press CD (
on
The stations are stored in memory from the lower
the remote).
frequencies to the higher ones automatically.
Press CD (
on
the remote).
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
Press CD (
on
the remote).
1
Press RADIO•BAND•AUTO PRESET
the remote) to select the band.
Press
or
then
2
Tune in a station you want.
press DISPLAY•ENTER
3
Hold down DISPLAY•ENTER
(ENTER
on the remote)
remote) for 2 seconds until the preset number
for the tracks (up to 20) you
flashes in the display.
want to program in the order
4
you want. Then press CD
Press PRESET + or –
until the preset number you
(
want for the station flashes in the display.
on the remote).
5
Press DISPLAY•ENTER
Playing order
The new station replaces the old one.
Tip
The preset radio stations remain in memory even if you unplug the
AC power cord or remove the batteries.
Press
or
then
press DISPLAY•ENTER
(ENTER
on the remote)
Playing preset radio stations
for the tracks (up to 20) you
want to program in the order
1
Press RADIO•BAND•AUTO PRESET
you want. Then Press CD
the remote) to select the band.
(
on the remote).
2
Press PRESET + or –
to tune in the stored station.
(MODE
on the remote)
Using the display
iPod mode
To use iPod backlight
(ENTER
on the remote).
Press DISPLAY
on the remote.
CD mode
To check the total track number and playing
time
In stop mode, press DISPLAY•ENTER
on the remote).
To check the remaining time
Press DISPLAY•ENTER
remote) repeatedly. The display changes as follows:
The current track number and playing time
The current track number and the
remaining time of the current track*
The number of tracks left and remaining
repeatedly
time on the CD
and BAND
* For tracks numbered over 20, the remaining time appears as "- -:- -"
in the display.
Radio mode
To display the frequency or a preset station
until the frequency
number
Each time you press DISPLAY•ENTER
on the remote), the display changes to the frequency or a
preset station number ( if you have preset any).
Connecting optional components
You can enjoy the sound from an optional component
(MODE
such as a portable digital music player through the
speakers of this unit. Be sure to turn off the power of
each component before making any connections. For
details, refer to the instruction manual of the component
to be connected.
1
Connect the AUDIO IN jack
unit to the line output jack of the portable digital
music player or other components using an audio
connecting cable (not supplied).
(MODE
on the remote) for a few
2
Turn the unit and the connected component on.
3
Press AUDIO IN
and start playing sound on the
connected component.
The sound from the connected component is output
from the speakers of this unit.
To connect the unit to a TV or VCR, use an extension
cable (not supplied) with a stereo-mini jack on one
pressed, disconnect the AC
end and two phono plugs on the other end.
pressed, reconnect the AC
(BAND
on
(BAND
(ENTER
on the remote).
(BAND
on
(ENTER
on the
(ENTER
on the remote).
(BAND
on
(DISPLAY
(DISPLAY
on the
(DISPLAY
on the back of the
Advertisement
