Central Machinery 47158 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Drill
  5. 47158
  6. Assembly and operating instructions manual

Central Machinery 47158 Assembly And Operating Instructions Manual

Micro mill/drill machine
Hide thumbs

Advertisement

Table of Contents

MICRO MILL/DRILL MACHINE
Model 47158
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
Copyright
by Harbor Freight Tools
. All rights reserved. No portion of this
©
®
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.

Advertisement

Table of Contents
loading

Related Manuals for Central Machinery 47158

Summary of Contents for Central Machinery 47158

  • Page 1 Harbor Freight Tools . All rights reserved. No portion of this © ® manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.

  • Page 2: Specifications Table

    Electrical Requirements  Speed Ranges Maximum Chuck Capacity 5/64” Drill Bit / 5/64” End Mill / 3/4” Face Mill Maximum X Travel Maximum Y Travel Maximum Z Travel X, Y, Z Graduations Table Size Table Slot Throat Depth Swing Diameter...
  • Page 3 Also, use an ANSI approved dust mask if the operation produces excessive dust. ANSI approved safety impact eyeglasses and dust masks are available from Harbor Freight Tools. DRESS SAFELY. Do not wear loose clothing or jewelry, as they can become caught in moving parts.

  • Page 4: Specific Product Warnings And Precautions

    Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use the Micro Mill/Drill Machine in areas near flammable chemicals, dusts, and vapors. Do not use the Micro Mill/Drill Machine in a damp or wet location.
  • Page 5 Worktable (part #105) with a vise or clamps. If the workpiece begins to spin, do not attempt to stop it with your hands. Turn the Micro Mill/Drill Machine OFF, and wait until the workpiece stops spinning before attempting to remove it.
  • Page 6 When unpacking, check to make sure all the parts shown on the Parts Lists on pages 12 and 13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
  • Page 7 Use the four mounting holes in the Base (part #74) of the Micro Mill/Drill Machine as a template, and trace with a pencil on the top of the workbench four 3/8” diameter mounting holes . Then, temporarily remove the Micro Mill/Drill Machine from the workbench.
  • Page 8 Then, secure the Micro Mill/Drill Machine to the workbench, using the four 3/8” diameter bolts of appropriate length, four lock washers, and four nuts as mentioned in Step #. MACHINE ADJUSTMENT INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 14.

  • Page 9: Operating Instructions

    Worktable with clamps (not provided). (See Figure B, and Assy. Diagram.) Insert the shank of the drill bit/cutting tool (not provided) all the way up into the Chuck (part #13). Then, use the Chuck Key to tighten the Chuck onto the drill bit/cutting tool.
  • Page 10 If necessary, use the Lifting Hand Wheel, Longitudinal Feed Hand Wheel, Cross Feed Hand Wheel, and Fine Feeding Hand Wheel (parts #97) to adjust the Micro Mill/Drill Machine for the work to be done. NOTE: Do not attempt to make any further adjustments while the machine is running.

  • Page 11: Inspection, Maintenance, And Cleaning

    Do not use damaged equipment. DAILY: With a soft brush, cloth, or vacuum, remove all debris from the Micro Mill/ Drill Machine. Then, use a premium quality, lightweight machine oil to lubricate all moving parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.

  • Page 12: Parts List

    PARTS LIST Clutch For technical questions, please call 1-800-444-3353. SKU 47158 Page 1...
  • Page 13 PARTS LIST Variable Speed High/Low Speed Power Cord/ Lengthways For technical questions, please call 1-800-444-3353. SKU 47158 Page 13...

  • Page 14: Assembly Diagram

    ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. For technical questions, please call 1-800-444-3353. SKU 47158 Page 14...

  • Page 15: Schematic Diagram

    SCHEMATIC DIAGRAM Yellow Lamp (fault) Green Lamp Fuse Potentiometer Forward/Off/Reverse Motor Switch 110V/60Hz REV 08/04 For technical questions, please call 1-800-444-3353. SKU 47158 Page 15...

  • Page 16: Wiring Diagram

    WIRING DIAGRAM REV 07/06 For technical questions, please call 1-800-444-3353. SKU 47158 Page 16...

Table of Contents