Central Machinery 44991 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Drill
  5. 44991
  6. Assembly and operating instructions manual

Central Machinery 44991 Assembly And Operating Instructions Manual

Mini vertical milling/drilling machine
Hide thumbs

Advertisement

Table of Contents

MINI VER
MINI VER
MINI VER TICAL MILLING/
MINI VER
MINI VER
DRILLING MACHINE
DRILLING MACHINE
DRILLING MACHINE
DRILLING MACHINE
DRILLING MACHINE
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2000 by Harbor Freight Tools
this manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
TICAL MILLING/
TICAL MILLING/
TICAL MILLING/
TICAL MILLING/
44991
®
. All rights reserved. No portion of
®

Advertisement

Table of Contents
loading

Related Manuals for Central Machinery 44991

Summary of Contents for Central Machinery 44991

  • Page 1 Copyright © 2000 by Harbor Freight Tools this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353...

  • Page 2: Specifications

    Do not force tool. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool capacity. SKU 44991 Specifications DESCRIPTION 120 VAC, 60 Hz, single phase...
  • Page 3 If there is any doubt, do not operate the tool. 19. Use proper size and type extension cord. If an extension cord is required, it must be SKU 44991 Page 3...

  • Page 4: Installation

    When unpacking, check to make sure the following parts and accessories are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

  • Page 5: Operation

    An optional oil pan can be placed under the machine before it is mounted to the table. Before operation, loosen the slide, worktable, and drill-mill spindle. They were locked for shipping. Remove all packing material and clean machine with nonflammable solvent. Oil the machine according to the lubrication requirements before running the machine.
  • Page 6 Using a plastic hammer, gently tap the Taper Shank (B) until it breaks free. Place a cushion on the Working Table (19) to protect the assembly if it falls out. Replace the Taper Shank Cutter with the Drill Chuck (or other tool) if desired. Travel Adjustment Adjusting the Limit Block (65) can control the travel of the Spindle Box.
  • Page 7 Fine Feeding Wheel (93). Refer to the ruler on the Vertical Support to determine drilling or milling depth. Caution: Keep hands and fingers clear of the working table and workpiece while the machine is in operation. SKU 44991 Page 7 (68)

  • Page 8: Maintenance

    BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 44991 Maintenance Page 8...

  • Page 9: Parts List

    Parts List NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 44991 Page 9 REV 03/05...
  • Page 10 SKU 44991 Page 10 REV 11/02...
  • Page 11 Longitudinal (Y) Axis and Cross (X) Axis Assembly Drawing SKU 44991 Page 11...
  • Page 12 Vertical (Z) Axis Assembly Drawing SKU 44991 Page 12...
  • Page 13 Spindle and Gear Box Assembly Drawing SKU 44991 Page 13...

Table of Contents