Table of Contents
Advertisement
OPERATION OF REMOTE CONTROL
Universal Remote Control
With the purchase of your Digital Tuner you also have
received the latest innovation in remote control technology.
With its easy-to-use push button keypad, your remote can
control your Digital Tuner and most infrared remote con-
trolled TVs, VCRs and cable TV converters as well.
NOTE
• Depending on the model, year produced, brand and type of TV, cable TV
converter box, and VCR, some models may not be compatible with the
remote control.
• Some brands of TV or cable TV converter box may not enable channel
selection until the
is pressed.
Example:
To select channel 24,
(1) Press
(2) Press
(3) Press
For detailed information on the use of your cable TV converter box or TV,
refer to their operating manuals.
Using Your Remote Control with the Digital Tuner
After installing the batteries, press DTV button. (If you can
change the channel of the Digital Tuner by pressing CH UP
(
) or DOWN (
) on the remote control, it is in the
Digital Tuner position.)
USING YOUR REMOTE CONTROL WITH A VCR
Once you make certain the remote control has "identified" your remote controlled VCR, the remote control is ready to
operate your unit. The various VCR function buttons on the remote control will not operate your VCR if those functions are
not found on your unit.
• All VCR buttons will operate whether the remote control is in DTV, TV or CATV modes.
• For detailed information on the use of the VCR, refer to the operation manual of the VCR.
REWIND 1
Press to rewind a tape. For some
VCRs you may need to press STOP
first, then REWIND.
In Playback mode, hold button down to
view picture moving rapidly in reverse.
PLAY 3
Press to play back a tape.
PAUSE 8
Press to temporarily stop the tape during
playback or recording. Press again to release
Pause.
STOP
Press to stop the tape.
NOTE
• When operation buttons common to the DTV, TV and cable TV converter
box (such as the CHANNEL UP/DOWN buttons) are pressed, the remote
control mode select button for the device being controlled will light up. To
operate a device other than that currently being controlled, press the
appropriate remote control mode select button and then the desired
operation button.
"Identifying" Remote TV, VCR and Cable TV Con-
verters
Your remote control has been set at the factory to operate
your Digital Tuner and many remote controlled TVs, VCRs,
and cable converters. However, in some cases an easy
one-time set-up step may be necessary before the remote
will operate these devices.
• In this set-up step, the remote locates and memorizes the
remote control transmitter codes for the TV, VCR or cable
converter.
• Once "identified", the remote sends the proper remote
signals to operate the electronic devices.
• This procedure will not have to be repeated until power to
the remote is interrupted due to a battery failure.
INFO
ª
5
MENU
·
∞
CH LIST
CC
1
2
3
VIEW MODE
4
5
6
CLEAR
7
8
9
ENT
CH RETURN
0
100
DTV/480I
AUDIO
INPUT
AIR/CABLE
1
3
¡
REW
PLAY
FF
5
8
7
¶
VCR CH
PAUSE
STOP
REC
∞
VCR
POWER
DIGITAL TUNER
Numeric buttons
Use to enter two-digit code numbers when
identifying your VCR.
ENTER
FF ¡
Press to rapidly advance the tape. For some
VCRs, you may need to press STOP first, then
FF.
In Playback mode, hold button down to view the
picture moving rapidly in forward direction.
VCR CHANNEL UP (5) / DOWN (∞)
Press to scan up or down through the channels
on the VCR.
VCR POWER
Press to turn the VCR on and off.
RECORD ¶
Press to begin recording.
45
Advertisement
Table of Contents
