Table of Contents
Advertisement
HDMI Functions
Control with HDMI "
∗Enjoy additional HDMI Inter-Operability with Panasonic products which have "HDAVI Control" function.
HDMI connections to some Panasonic equipment (Panasonic DVD Recorder DIGA, Panasonic Player
theatre, Panasonic Amplifier, etc.) allow you to enjoy easy playback or home theatre.
About connections, see "External Equipment" (p. 44). Read the manuals of the equipment too.
This function needs an HDMI compliant (fully wired) cable.
Non-HDMI-compliant cables cannot be utilized.
Consult your local Panasonic dealer or refer to the URL for applicable equipment: www.panasonic.co.uk
Preparations
(For the first time / When adding new equipment, reconnecting equipment or changing setup)
After connection turn the equipment on and then switch the TV on.
Select the input mode to HDMI1, HDMI2 or HDMI3 (p. 16), and make sure that
an image is displayed correctly.
Display the menu
1
Select "Setup menu"
2
Ma in me n u
3
Select "Control with HDMI"
Setup menu
Q-Link
AV2 out
Control with HDMI
Off timer
Side panel
Power save
Power on preference
SD card LED
DVB Setup Menu
Owner ID
Shipping condition
4
Select "On"
IDTV
(default is On)
■
To return to TV
•
It is recommended that you use Panasonic's HDMI cable.
Recommended part number:
RP-CDHG15 (1.5 m)
RP-CDHG30 (3.0 m)
RP-CDHG50 (5.0 m)
42
(Continued)
Control
" ∗
TM
Ho me th e a tre
Pic tu r e me nu
access
So u n d me n u
select
Se tu p me n u
•
Displayed when Amplifier or Player theatre is connected.
This may be displayed after disconnecting the equipment.
In this case, set "Control with HDMI" in Setup menu to
"Off", then set to "On" again.
AV2
Monitor
On
Off
Off
select
Off
TV
On
select
Automatic Input switching-When the connected Panasonic equipment is operated,
Easy
input mode is switched automatically. When it is stopped operating, input mode is
playback
returned.
You can control the theatre speaker with TV's remote control.
This function is available when Panasonic Amplifier or Player theatre is connected.
Display the menu
Select "Home theatre" or "TV speaker"
M ai n me nu
H ome t he at re
Pict ure menu
Theatre
Sound me nu
speaker
Set up me nu
•
When selecting "Home theatre", the sound of TV speakers is mute.
•
When the equipment is turned off, TV speakers will be active.
When the connected Panasonic equipment starts playback or direct navigator or
Power on
function menu are activated, the TV is automatically turned on. (Only when TV is
link
in Standby mode.)
Power off
When TV is set to Standby mode, the connected Panasonic equipment is also
link
automatically set to Standby.
Note
•
Setup the equipment to enable this function. Read the manual of the equipment.
•
This function may not work normally depending on the equipment condition.
•
This function may not work normally when Panasonic Player theatre is connected.
•
The equipment can be operated by TV's remote control with this function on even if TV is in Standby mode.
•
Image or sound may not be available for the first few seconds when the playback starts.
•
Image or sound may not be available for the first few seconds when Input mode is switched.
•
Volume function will be displayed when adjusting the volume of the equipment.
•
Easy playback is also available by using the remote control for Amplifier. Read the manuals of Amplifier.
■
Home theatre:
Adjustment for equipment
(automatically turned on if it is in
access
Standby mode)
select
Volume up / down
Mute
■
TV speaker:
TV speakers are active.
43
Advertisement
Table of Contents
