Panasonic NV-FJ620 Operating Instructions Manual page 18

Power save:
– Set Power save mode as follows:
[ON]:
[OFF]:
Refer to the followings when [Power save] is set to
[ON].
– [VCR display] is automatically set to [OFF].
– To turn the VCR on, keep the [VCR-ON/OFF] button
pressed on the VCR main unit. It is not possible to
turn it on with the remote control.
– The Power save function does not work in the timer
recording standby mode. After all programmed timer
recordings have been made, and after all
programmed data have been erased, the VCR
switches over to the Power save mode.
– When the VCR is off, Pay TV programmes cannot be
watched on the TV because the signal from the
connected decoder is not looped through. To watch
them, turn on the VCR. (For NV-FJ620 Series,
NV-FJ621 Series and NV-FJ616 Series)
VCR display:
– Set the brightness of the VCR display as follows:
[ON]:
[OFF]:
[DIMMED]:
OSD:
– Set OSD mode as follows:
[4:3]:
[16:9]:
– Even if setting to [16:9], indications may be cut off
depending on the TV.
[OFF]:
AV2:
– Set the external source equipment as follows:
[DECODER]:
[EXT LINK 1]:
[EXT LINK 2]:
[EXT]:
18
To reduce the VCR's power
consumption when the VCR is
switched off.
The power consumption is greatly
reduced when the VCR is turned off.
The power consumption is not reduced
when the VCR is turned off.
For automatic change of the brightness
of the VCR display when the VCR is
switched off.
Indications are brightly lit.
Indications are not lit.
Indications are dimly lit.
For automatic display on the TV
screen of the TV station information,
type of sound system of the
programme being watched and the
sound playback mode. (See page 19.)
Indications can be displayed on the TV
screen.
Indications can be displayed on the TV
screen when using wide type of TV
screen and selecting the wide screen
mode on the TV setting.
No indications appears.
To select the type of external source
equipment which is connected to the
VCR's AV2 21-pin socket.
(For NV-FJ620 Series, NV-FJ621
Series and NV-FJ616 Series)
When a decoder is connected.
When a digital receiver which transmits
a special control signal recordings via
the 21-pin Scart cable, for example the
F.U.N. receiver (TU-DSF30/S3) is
connected for the linked timer
recordings. (See page 11.)
When an external equipment with a
timer function is connected for the
linked timer recordings. (See page 11.)
When another VCR or a satellite
receiver is connected.
AV: To select the type of external source
equipment which is connected to the
VCR's AV1 21-pin socket.
(For NV-SJ220 Series)
– Set the external source equipment as follows:
[TV/EXT]: When TV, another VCR or a satellite
receiver is connected.
[EXT LINK 1]: When a digital receiver which transmits
a special control signal recordings via
the 21-pin Scart cable, for example the
F.U.N. receiver (TU-DSF30/S3) is
connected for the linked timer
recordings. (See page 11.)
[EXT LINK 2]: When an external equipment with a
timer function is connected for the
linked timer recordings. (See page 11.)
TV system: To select the type of colour TV system
to be used during playback or during
recording from an external source.
– Set the colour TV system as follows:
[PAL]: When PAL system is used.
[MESECAM]: When SECAM system is used.
Press the [OK] button to conclude the setting.
OK
Press the [EXIT] button to exit the On Screen Display.
EXIT