Advertisement
Krypto Sync™
in master/slave configuration. The connection uses a 3.5mm stereo
microphone jack. The input is used when a unit has been selected as
a slave unit. The input connection requires a 3.5mm microphone jack.
7.
Master LED - This green LED will glow when the unit has been
designated a Master unit, in a Master/Slave configuration.
8. Dip Switches - When dipswitch #1 is in the "On" postion, the unit
is designated as the Master, in master/slave mode.
9. AC Adapater Connection - This connection is used to supply
main power to the fixture. Use only the supplied AC adapter. Be sure
the main power matches the required power of your fixture.
10. Microphone - This microphone receives external low frequencies
to trigger the unit in Sound-Active mode. This microphone is designed
to receive low frequency sounds only, tapping on the microphone and
high pitch sounds may not trigger the unit.
Krypto Sync™
CAUTION IMPORTANT! : When installing this projector, make
sure that it is mounted in a manner that prevents the audience
from looking directly into the beam, and that the beam will not
strike the audience.
Power Supply:
This unit is available in 120v, before plugging your
fixture in be sure the source voltage in your area matches the required
voltage for your American DJ
General Operation:
Plug and Play operation. The Krypto Sync
has been tested at the factory there is no assembly necessary. The
Krypto Sync™ is ready to be plugged in, out of the box. This Krypto
Sync™ is a sound active unit that can function as a stand-alone unit,
or in a Master/Slave configuration. The unit comes with several built-
in patterns that automatically cycle through when the unit is operat-
ing, the patterns may not be selected manually. If the unit does not
turn on, be sure the AC apapter is not bad, and then be sure the unit
is properly plugged in to a matching wall outlet. If problem continue
to persist, please contact customer support for further instructions.
Stand-Alone Mode: After the unit has been plugged in, flip the
American DJ
- www.americandj.com - Krypto Sync™ Instruction Manual Page 9
©
®
Control & Functions
Krypto Sync.™
®
Krypto Sync™
mode switch to the right position. The unit should then start project-
ing the laser at whatever it is facing.
Master/Slave Mode: When set-up in a Master/Slave configuration,
one unit is chosen as the master, the other units that are linked will
follow whatever pattern the master projects. To set-up Master/Slave
mode:
1. Select which unit will act as master, by putting dipswitch #1 into
the "on" postion, and connect the 3.5mm cable into the output con-
nection on the back of the unit. The green LED on the back of the
Master unit should glow.
2. Then simply connect the other end of the cable to the back of the
slave unit, where the input connection is.
To connect more than one slave unit. Connect another 3.5mm cable
to the output connection on the back of the slave unit, to the input
connection on the back of the second slave unit and so on.
Operation
Krypto Sync™
Fixture Cleaning:
the internal and external lenses should be carried out periodically to
optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out
side casing.
2. Clean the external optics with glass cleaner and a soft cloth every
20 days.
3. Always be sure to dry all parts completely before plugging the
unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-
mend cleaning on a monthly basis. Periodic cleaning will ensure lon-
gevity, and crisp beam output.
American DJ
©
Due to fog residue, smoke, and dust cleaning
- www.americandj.com - Krypto Sync™ Instruction Manual Page 10
®
Operation cont.
Cleaning
Advertisement
