Advertisement
14.
5
• Turn power supply on to range.
Product Damage
Carefully place burner cap over
1
_
electrode.
Fallure to do so may damage
electrode.
_
_
I \\ 20 23
electrode
-
__ _,_
_locating
Numbers
\_\\
____l_
1 _,
sots
Align locating
tabs on
correspond
____
_1 burner caps with locating
slots in burner
to steps.
_
__-
base, Burner cap should be level when
properly
positioned,
Place burner grates
over burners and caps.
Fire Hazard
Do Not make connection
too fight. The
regulator Is dle cast.
Overtlghtenlng
may crack the regulator,
resulting In a gas leak and possible fire or
explosion.
All connections must be wrench-tightened.
flexible
pressure regulator ___. _--=='_
I( o )
ex:_.<l_
fl_lrael _; 'ren ---T
_u_tnoff
shutoff
P
valve -electric
valve
_
Ignition models
only
__
o_n it
Besure lever is
in "on" position
when installation
gas supply
is complete.
n
Pull range
forward
to make gas
connections,
Assemble
the flexible
connector
from the gas supply pipe to the
pressure regulator,
located
on the lower
right hand side on the back of the range,
in
this order: shutoff valve,
1/2'" flare union
adapter,
flexible connector,
1/2" flare union
adapter.
Seal all openings
in floor or wall
wherever
range
is installed.
0
•
Use pipe-joint
compound
made
for use with Natural and L.P. gas to seal all
gas connections.
If flexible connectors
are
used, be certain
connector
is not kinked.
I
II
•
Open the shutoff valve in the gas
"1
supply line. Wait a few minutes for gas to
move
through
the gas line.
Flre Hazard
Do Not use an open flame to test for leaks
from gas connections.
Checklng for leaks wlth a flame may
resultIn a fire or exploslon.
2
• Use a brush
and liquid detergent
to test all gas connections
for leaks.
Bubbles
around
connections
will indicate
a leak.
If a
leak appears,
shut off gas valve controls
and
adjust connections.
Then check
connections
again.
NEVER TESTFOR GAS
LEAKSWITH A MATCH OR OTHER FLAME.
Clean all detergent
solution
from range.
3
• Plug power supply cord into
grounded
outlet.
4•
Move
range into final
position.
Grasp rear of range and
carefully
try to tip range
forward
to check
that both rear leveling
legs are engaged
in anti-tip
brackets.
If you have electronic controls: Push the
"BAKE" pad and "350 °" will appear
in the
display.
Press the "START/ENTER" pad and
"Lo °', "HEAT" and "BAKE" will appear
in the
display.
The oven burner should light In 50 to
60 seconds. Thls delay Is normal. The oven
safety valve requires a certain
time before
it
will open and allow gas to flow.
Product Damage
• Do Not Insert any object Into the
openings of the protective
shleld that
surrounds the Ignitor.
• Do Not clean the area.
Fallure to follow these Instructlons could
result In product damage.
Electronic
Ignition
System
initial lighting and gas flame
adjustments.
Cooktop
and oven burners use electronic
ignitors in place
of standing
pilots. When the
cooktop
control
knob is turned to "LITE"
position, the system creates
a spark to light
the burner.
This sparking
continues
until the
control
knob is turned to the desired
setting.
When the oven control
is turned to the
desired setting, a glow bar heats up bright
orange
and ignites the gas. No sparking
occurs and the glow bar remains on while
the burners operate.
17•
Checktheoperafion
_
of the cooktop
burners.
Push in
/ _
_
_
and turn each
control
knob to
_-_ I _
_ -_
"LifE" position.
The flame should
\ o _-
,/_,4/
light within 4 seconds.
Do Not
\
_
- /
leave the knob In the "LITE" position _
/
after burner lights.
Note: All ignitors will spark when any burner
knob is in the "LITE" position.
1
•
Check the oven
burner for proper
flame. Thisflame
should have a 1" long
inner cone
of
bluish-green,
with an outer mantle
of dark blue, and should be clean
and soft in character.
No yellow
tips, blowing
or lifting of flame
should occur.
broiler
hood
hoe°
lock screw
22
air shufe,
•
orifice he
If oven flame needs
to be adjusted,
locate
the air
shutter near the center
rear of the range.
Loosen the lock screw and adjust the air
shuffer until the proper
flame
appears.
Tighten screw.
•
23
18
.or T0uuuu0,uuuu "
burner lights, turn
control
knob to "HI"
i
i
position.
Check each
cooktop
burner for proper
flame.
At the "HI"
selling, the small inner cone should have a
very distinct blue flame
approximately
5/8"
long.
The outer cone
is not as distinct as the
inner cone.
If any burner needs to be
adjusted
or does not light properly,
contact
your dealer
or authorized
service company
for assistance.
/gas supply line
19,
To
i.,J
valve
stem
check and adjust the lowest _
setting of surface burner
-q.-"
valves: Push in and turn surface
burner
_'_
control
knob to "LITE" position.
Quickly turn
_,,
the control
knob to the "LOW" position
after
burner lights.
Check
surface burner for proper flame. The low
flame
should be a minimum,
steady,
blue flame.
If surface
burner flame goes out, turn control
knob to "OFF" position. Remove
the control
knob. Insert a flat-blade
screwdriver
into valve
stem. Turn the slotted
screw to increase
or
decrease
the flame size. Adjust the screw until
the smallest flame
possible stays lighted
when
the control
knob is turned quickly
form "LITE" to
the "LOW" position. Adjust each
surface
burner
as needed.
Note: No air mixture adjustment
to surface
burners is required.
0
•
Remove the oven bottom.
Check the operation
of the oven burner.
If you have oven selector and temperature
selector control knobs: Push in and turn the
oven selector
knob to "Bake."
Push in
and turn temperature
control
_
,,_-"_
knob to 300°F. The oven burner
/_
should light In 50 to 60 seconds.
/_._/_
Thls delay Is normal. The oven
_I
'
safety valve requires a certain
_\
time before it will open and allow _';_
gas to flow.
_"
Replace
the oven bottom
and
storage
drawer.
)4
Check the operation
of the
•
oven broil burner.
If you have oven selector and temperature
selector
control knobs: Turn the oven
selector
knob to "BROIL". Push in and turn
the oven temperature
selector
knob to
"BROIL", The oven broil burner should light In
50 to 60 seconds. This delay Is normal. The
oven safety valve requires a certain
time
before it will open and allow gas to flow.
If you have electronic
controls: Push the
"BROIL" pad and "HI" will appear
in the
display. Press the"START/ENTER" pad and
"HEAT", "BROIL _ and "HI °" will appear
in the
display. The oven broil burner should light In
50 to 60 seconds. This delay Is normal. The
oven safety valve requires a certain
time
before it will open and allow gas to flow.
alr shutter
I!
.1/
25
,,,.o
noo=
•
adjustment:
a Loosen lock screw on the air shutter
located
at the rear of the broil burner.
b. Adjust the air shutter as needed.
The
flame should
have a 1" long, inner cone
of bluish-green
with an outer mantle
of
dark blue. The flame
also should be clean
and soft in character
with no blowing
or
lifting of flame. Tighten the lock screw.
To get the most efficient use from
your new range, read your Use and
Care Guide. Keep Installation
Instructions and Guide close to
range for easy reference.
Panel C
Advertisement
