Advertisement
Electrical
if your house has aluminum vvMng, see
"Ebctdcal requirements',' Page 2.
Ebctrbal 8hock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.
Faiture to follow these instructions can result
in death, fire, or electrical shock.
This range is manufactured
with white
(neutral)
power suppJy wire and a cabinet-connected
bare
ground wire twisted
together.
Make electrical connection following the
steps needed for your installation.
1. Disconnect the power suppJy.
2. Remove the junction box cover.
3. Connect range cable to junction box through
the U.L.qisted conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
cable
from
junction
pow
box _
red _
white and ba_
ground
range
cable wires --
factory
crimped
cable from
Figure 1
range
conduit
connector
if local codes PERMIT
connecting
cabinet-ground
conductor
to neutral white
wire in junction box:
7. Connect the factory-crimped
bare and white range cable
wires to the neutral (white) wire
in junction box. See Figure 1.
8. Replace junction box cover.
cable from
junction
power
supply
Figure 2
cable
from
connector
range
if local codes DO NOT PERMIT
connecting
cabinet-ground
conductor
to neutral white
wire in junction
box:
7. Separate the factory-crimped
bare and white range cable
wires.
8. Connect white range cable wire
to neutral (white) wire in
junction box. See Figure 2.
9. Connect the bare ground range
cable wire to a grounded wire in
the junction box. See Figure 2.
10. Replace junction box cover.
ff connecting
to a
four-wire electrical system:
7,Separate factory-crimped bare
and white range cable wires.
8. Connect white range cable wire
to neutral (white) wire in
junction box. See Figure 2.
9. Connect the bare ground range
cable wire to the green ground
wire in junction box. Do Not
connect bare ground wire to
neutra_ (white) wire in junction
box. See Figure 2.
10. Replace junction box cover.
Attachment
Carefully push against sea_area of range front
frame when pushing range into cabinet.
Do Not push against outside edges.
5m
Lift'__using
the
oven opening
as an area to grip. Be careful not to
damage countertop.
J
shipping
foot
To avoid damaging the countertop, lift range
slightly while pushing against seal area of front
frame. Push range into cabinet cutout until
shipping feet almost contact cabinet. Use a
Phillips screwdriver to remove screws attaching
shipping feet. Remove and discard shipping
feet.
Push range completely
into cabinet and center
range in cabinet cutout. Be careful not to
damage countertop.
Tip Over Hazard
A child or adult can tip the range and be killed.
Securely attach mounting screws to cabinet.
Reattach mounting screws if the range is
moved.
Failure to follow these instructions can result
in death or serious burns to children and
adults.
%@
2 screws
6m
Important: Securely fasten range to cabinet
using the two screws provided. Insert the screws
through hobs in mounting rails. Do Not
overtighten screws.
Push trim
into
place,
Replace
trim screw.
7m
Siidetop
end of each trim upward
onto
range side rails. Push each trim into place at
bottom
of trim.
Use screws to attach each trim to
range. Take care not to scratch other surfaces with
ends of trim,
8m
Replace oven racks.
Reinstall the oven door by inserting ends
of hinges into hinge slots in the oven frame. Push
hinges in as far as they wiii go. Open the door (you
will feel the door drop into place) and rotate both
hinge btches back to the locked position.
Close and open the door to checkthat the door
closes and opens completely, if door does not close
or open completely, repeat the door removal step
and reinstall door as described above.
Check operation
Turn on power supply.The display
panel wili light up briefly. "PF" should appear in
the temperature display.
8
_
7
OFF_
o5
oo
0 @
L0
l_
"
Check the operation of the cooktop
ebments. Push in and turn each surface unit
control knob to "Hi" position. Check the operation
of the cooktop elements and indicator lights.
2m
Check the operation of the oven
eJement. Press the "BROI[' pad. "BROH/: will
appear in the display. Press the "START" pad.
Make sure the oven door is closed and the "ON"
light is shown in the display area. After 2 minutes,
partially open oven door. You should feel heat
from the oven. Press the "CANCEr' pad.
If your oven does not heat or an "F'_followed by a
number, appears in the display, contact your
dealer or check the "if you need service..:' section
of this Installation instructions.
Page 3
Advertisement
