Table of Contents
Advertisement
Yoursafety and the safety of others is
very important.
We have provided many important safety
messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol. This
symbol alerts you to hazardsthat can kill
or hurt you and others. All safety messageswill be
preceded by the safety ale!t symbol and the word
"DANGER or"WARNING . These words mean:
All safety messageswill identify the hazard, tell you
how to reducethe chance of injury, and tell you
what can happen if the instructions are not
followed.
Grounded electrical
outlet is required. See
"Electrical requirements,"
Page 3.
Proper gas supply
connection must be
available. See "Gas
supply requirements,"
Page 3.
27-1/8" depth
with
®©
40-7/8"
overall
height
WARNING:
If the information
in
this manual
is not followed
exactly,
a fire or explosion
may
result
causing
property
damage,
personal
injury
or death.
m Do not store
or use gasoline
or
other
flammable
vapors
and
liquids
in the vicinity
of this or
any other
appliance.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any
appliance.
• Do not touch
any electrical
switch.
• Do not use any phone
in your
building.
• Immediately
call your
gas
supplier
from a neighbor's
phone.
Follow
the gas
supplier's
instructions.
• If you cannot
reach your
gas supplier,
call the fire
department.
= Installation
and service
must
be performed
by a qualified
installer, service
agency
or
the gas supplier.
important: Observe all governing
codes
and ordinances.
Do not obstruct flow of combustion and
ventilation
air.
This installation must conform with all local
codes and ordinances, in the absence of
local codes, installation must conform
with
American
National Standard,
National Fuel
Gas Code ANSI Z223.1 -- latest edition*
or
CAN/CGA--
B149-
latest edition***
installation codes.
It is the customer's
responsibility:
• To contact a qualified
electrical
installer.
• To assure that the electrical
installation
is adequate and in conformance
with
National Electrical Code, ANSl/NFPA
70
-- latest edition**,
or CSA Standard
C22.1, Canadian Electrical
Code, Part 1
-- latest edition
***, and all codes and
ordinances.
Cabinet opening dimensions shown must be
used. Given dimensions are minimum
clearances.
When installing a cooktop under existing
cabinets and the installation does not meet the
minimum cabinet clearances, install a range
hood above the cooktop to avoid burn hazards.
Proper installation is your responsibility. A
qualified technician must install this range. Make
sure you have everything necessary for correct
installation. It is the installer's responsibility to
comply with installation clearances specified on
the gas information label. The gas information
label and model/serial rating plate are located on
the frame behind the storage drawer.
Page 2
_-
29-7/8" width
Check location
where
range will be installed.
The range
IMPORTANT:
Some cabinet and building
materials
are not
should be located
for convenient
use in the kitchen,
designed
to withstand
the heat produced
by the oven for
Recessed
installations
must
provide complete
enclosure
of
baking
and self-cleaning.
Check with
your
builder
or cabinet
the sides and rear of range,
supplier to make sure that the materials
used will net
ALL OPENINGS
IN THE WALL OR FLOOR WHERE
RANGE IS
discolor, delaminate
or sustain other
damage.
TO BE iNSTALLED
MUST BE SEALED.
_p
of
I
_
cooktop,
see Note.***
30-1/8"
opening
18" rain.
_
width
clearance
upper
cabinet
to
countertop
Contact
a qualified
floor
covering
installer
to check
that the floor
covering
can
withstand
at least
200°F.
Use an insulated
pad
or 1/4" plywood
under range
if
installing
range
over
carpeting.
I
I
2" rain'.
countertop
space to side
wall
or other
combustible
material
I
17"
Do Not pinch the power
supply cord between the
range and the wall.
Do Not seal the range to
the side cabinets.
If cabinet depth
is greater
than
24", oven frame
must
extend
beyond
cabinet
fronts
by 1/2"
rain.
X,Y
This shaded area recommended
for installation
of rigid
gas pipe.
Flexible gas pipe and electrical
t are recommended
in either
Anti-tip
bracket
The floor-mounted anti-tip bracket MUST be installed. To
install the anti-tip bracket supplied, see Pages 4-5 and the
anti-tip bracket template/instruction
sheet.
***
Note:
24" rain. when
bottom
of wood
or metal cabinet is protected by not
less than
1/4" flame
retardant
mill-
board
covered with
not less than
No. 28 MeG sheet
steel,
0.015"
stainless
steel, 0.024" aluminum
or
0.020" copper.
_i_
30" rain. clearance
between
the top of
the cooking
platform
and the bottom
of an unprotected
wood
or metal
cabinet.
Mobile home installation
The installationof this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR, Part 3280 (formerly the Federal Standard for
Mobile Home construction and Safety, Title 24, HUD, Part
280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations (Manufactured Home
Sites, Communities and Setups), ANSI A225.1/NFPA 501A *_,
or with local codes.
In Canada, the installation of this range must conform with
the current standards CAN/CSA-Z240-- latest edition
, or
with local codes.
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
Copies of the standards
listed may be obtained
from:
* American Gas Association
1515 Wilson Boulevard
Arlington, Virginia
22209
** National Fire Protection Association
Ratterymarch Park
Quincy, Massachusetts 02269
***Canadian
Standard Association
178 Rexdale Boulevard
Etobicoke (Toronto), Ontario MgW 1R3
O
floor-mounted
anti-tip
bracket
2 plastic
anchors
Not shown:
• literature pack
• orifice spuds
(#10 x 1-1/2"}
Bracket must be securely mounted to
sub-floor. Thickness of flooring may
require longer screws to anchor
bracket to sub-floor. Longer screws
are available from your local hardware
store.
Advertisement
Table of Contents
