HP DL580 Quickspecs page 15

QuickSpecs
Standard Features
Rack Airflow Rack Airflow Rack Airflow Rack Airflow
Requirements Requirements Requirements Requirements
Rack Mounting Rack Mounting Rack Mounting Rack Mounting
Requirements Requirements Requirements Requirements
Factory Express Portfolio Factory Express Portfolio Factory Express Portfolio Factory Express Portfolio
for Servers and Storage for Servers and Storage for Servers and Storage for Servers and Storage
Rack 10000 series Cabinets The increasing power of new high-performance processor technology Rack 10000 series Cabinets Rack 10000 series Cabinets Rack 10000 series Cabinets
requires increased cooling efficiency for rack-mounted servers. The 10000 Series Racks provide
enhanced airflow for maximum cooling, allowing these racks to be fully loaded with servers using the
latest processors.
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure CAUTION: CAUTION: CAUTION:
adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and rear doors, you
must allow 5,350 sq cm (830 square inches) of hole evenly distributed from top to bottom
to permit adequate airflow (equivalent to the required 64 percent open area for ventilation).
Side: The clearance between the installed rack component and the side panels of the rack
must be a minimum of 7 cm (2.75 inches)
CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This CAUTION: CAUTION: CAUTION:
arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling
that can lead to thermal damage.
NOTE: For additional information, refer to the Setup and Installation Guide or the Documentation CD NOTE: NOTE: NOTE:
provided with the server, or to the server documentation located in the Support section at the following
URL: www.hp.com/servers/dl580-g4.
HP ProLiant DL580 G4 rack models provide tool-free support for racks with square or round mounting
holes (including Compaq/HP 7000, 9000, 10000, HP/E series and H9 series) with an adjustment range
from 24" - 36" in depth. The ambidextrous cable management arm can be mounted on either the left or
right side for improved cable management.
NOTE: Cable management arm must be removed to access Hot Plug Power Supplies when the cable NOTE: NOTE: NOTE:
management arm is mounted on the right.
HP ProLiant DL580 G4 in Telco Racks HP ProLiant DL580 G4 in Telco Racks HP ProLiant DL580 G4 in Telco Racks HP ProLiant DL580 G4 in Telco Racks
Support for all 2-post Telco racks requires the use of the standard rack kit and an additional option kit
from Rack Solutions (http://www.racksolutions.com/hp/)
HP Factory Express offers configuration, customization, integration and deployment services for HP
servers and storage products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading, asset
tagging, and custom packaging. HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000
servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network
switches.
For more information on Factory Express services for your specific server model please contact your sales
representative or go to: http://www.hp.com/go/factory-express.
DA - 12473 North America — Version 37 — June 11, 2008
HP ProLiant DL580 Generation 4 (G4) HP ProLiant DL580 Generation 4 (G4) HP ProLiant DL580 Generation 4 (G4) HP ProLiant DL580 Generation 4 (G4)
Page 15