Advertisement
\!/
17.
REQUIREMENTS. BE SUREYOU HAVE
CORRECT ELECTRICAL SUPPLYAND
RECOMMENDED GROUNDING
METHOD.
14.
if washer is not level, adjust
the front legs up or down.
Make final
check
with level,
When washer is level, use wrench
to turn nuts on front legs up tightly
against washer base. If nuts are not
tight against washer
base, the washer
may vibrate.
15. On
coin-operated
washers,
remove
the service door of the meter
case. Lift the service door up at the
back and remove.
Carefully
insert coin
slide with the coin slide extension
attached
into front opening
and
secure with the 3/16" mounting
bolt
from inside the meter case. The coin
slide may need to be partially
pushed
in to insert mechanism
in the front
opening.
Replace
meter case top and
service door, Insert coin vault with lock
and key,
Check that all parts are now installed,
See parts list, Page 3, If there is an
extra part, go back through
steps to
see which step was skipped,
9
mTurn on water
faucets
and
check
for leaks. Tighten couplings
if
there is leaking.
Do Not overtighten;
this could cause
damage
to faucets.
0
0
conversion
bar
\-
6 =put
the coin vault with lock
and key in the meter case opening.
A
larger-capacity
coin vault can be
installed.
Use a knife to carefully
remove
the paint along
the seam at
the bottom
of the conversion
bar, Use
a blade
screwdriver
and a hammer
to lightly tap along the seam area.
Raise the conversion
bar up to the
notches
in the sides of the vault
opening.
Remove the conversion
bar
and drawer
guide, Install new guide
(found
in parts bag) and the larger
coin vault,
PAGE 5
0mCheck
that you have all of
your tools. Check that the shipping
strap with 2 cotterpins
and plug was
removed
from the back of the washer
and used to secure the drain hose,
If entire strap is not removed,
washer
may vibrate and be noisy.
1.
Untape
power supply cord
and plug into grounded
outlet.
2.
Check the wash cycle time,
Both coin-operated
and non-coin-
operated
washers have timers with a
9-minute
wash in the Normal cycle.
Remove the meter case top of coin-
operated
washers to manually
start
the timer, Remove
the rear of the
console
to manually
operate
the
timer.
Remove the rear of the
console
to manually
operate
the
timer of non-coin-operated
washers.
Start the washer and allow it to
complete
the Normal cycle,
Rotate
counter-
clockwise
only. --
timer
"off"
--
position
timer-front
view
• Coin-operated
timers can be
started
by turning
the clutch
assembly
counterclockwise
until the
washer starts to fill with water,
cycle
,_%o
"_
information _
%._/÷_I
/_ _
- e-_\
Pull to start
_
I
Push to stop
top
0
__
Timer-rearview
• Non-coin-operated
timer cycle
information
is link stamped
on the
rear of the timer, Push in on the
lever attached
to the timer shaft.
Reset lever to the Normal cycle
position, then pull out on lever to
start washer,
timer clutch adjustment
screw
3.
If the washer fails to start or
does not give the proper
washer
cycle time, the clutch
assembly
of the
coin-operated
timer can be adjusted,
Remove the timer from the meter
case.
Adjust the clutch
assembly
screw clockwise
if the washer does
not start after the coin slide
mechanism
has been fully actuated
in or out. Adjust the clutch
assembly
screw counterclockwise
if the washer
segment
of the Normal cycle
was less
than 9 minutes.
Advertisement
